brake CITROEN C-ELYSÉE 2017 Handbook (in English)

104
Switching off the engine
F Stop the vehicle.Energy savings mode
For more information on the Energy
economy mode refer to the
corresponding section.
F

W

ith the engine running in idle, turn the key
to position 1 .
F

R

emove the key from the ignition switch.
F

T

o lock the steering column, turn the
steering until it locks.
To facilitate unlocking of the steering column,
it is recommended that the wheels be
returned to the straight ahead position
before switching off the engine.
F

C

heck that the parking brake is
correctly applied, particularly on
sloping ground. After switching off the engine (position
1- Stop
), for a maximum of 30 minutes you
can still use functions such as the audio and
communications system, the wipers, dipped
beam headlights, courtesy lights, ...
Never turn the ignition off before the
vehicle is at a complete stop. With the
engine off, the braking and steering
assistance systems are also cut off: risk
of loss of control of the vehicle.
When you leave the vehicle, keep the key
with you and lock the vehicle.
When opening the driver's door, an alert
message is displayed, accompanied by
an audible signal, to remind you that the
key is still in the ignition switch at position
1 (Stop) .
If the key has been left in the ignition
switch at position 2 (Ignition on) , the
ignition will be switched off automatically
after one hour.
To switch the ignition back on, turn the key
to position 1 (Stop) , then back to position
2 (Ignition on) .
Key left in the "Ignition on" position
Driving

105
Parking brake
LockingUnlocking
F Pull the parking brake lever up slightly,
press the release button, then lower the
lever fully.
When parking on a slope, direct your
wheels against the kerb, apply the parking
brake, engage a gear and switch off the
ignition. When the vehicle is being driven,
if this warning light and the STOP

warning light come on, accompanied
by an audible signal and a message
in the screen, this indicates that the
parking brake is still on or has not
been fully released.
Manual gearbox
Engaging reverse gear
F Press the clutch pedal fully down.
F

P
ush the gear lever fully to the right then
backwards.
F

P

ull the parking brake lever up to
immobilise your vehicle.
As a safety precaution and to facilitate
starting of the engine:
-

a
lways select neutral,
-

p
ress the clutch pedal.
Only engage reverse gear when the
vehicle is stationary with the engine at idle.
6
Driving

106
Electronic gearbox
Five-speed electronically controlled gearbox
which offers a choice between the comfort of
automated operation or the pleasure of manual
gear changing.
There are two driving modes:
-
a
utomated mode for automatic control
of the gears by the gearbox, without any
action by the driver,
-

man
ual mode for sequential changing
of the gears by the driver, using the gear
selector.
Gear selector
Displays in the instrument panel
Gear selector positions
N. Neutral.
R. Reverse.
1 2 3 4 5. Gears in manual mode.
AUTO. It comes on when the automatic
mode is selected. It switches off on
changing to manual mode.
F

P
lace your foot on the brake
when this warning light flashes
(e.g.: starting the engine).
R.
Reverse.
F

W

ith your foot on the brake, move
the selector for wards to select this
position. N.
Neutral.
F

W

ith your foot on the brake, select
this position to start the engine.
A. Automatic mode.
F

M

ove the selector backwards to
select this mode.
M + / -. Manual mode with sequential gear
changing.
F

M

ove the selector backwards,
then to the left to select this mode,
then:
-

p

ush for wards to change up a
g e a r,
-
o
r pull backwards to change down
a g e a r.
Driving

107
Moving off
F Select position N.
F P ress the brake pedal firmly.
F

S
tart the engine.
You must keep your foot on the brake
pedal while starting the engine.
If the engine does not start:
-
If N is flashing in the instrument panel,
move the selector to position A then to
position N .
-

I
f the “Foot on brake” message
appears, press the brake pedal
harder.
N appears in the instrument cluster.
F

Sel
ect automated mode (position A ),
manual mode (position M ) or reverse
(position R ) AUTO
and 1, 1 or R appear on the
instrument cluster.
F

R
elease the parking brake.
F

G
radually release the brake pedal.
The vehicle then moves off straight away
(refer to the section on the "Autonomous
traction function").
F
Accelerate.
Do not press the brake and clutch pedals
simultaneously. This can cause very rapid
wear on the clutch.Autonomous traction function
This function provides great flexibility in
manoeuvring the vehicle at low speed (when
parking, in traffic jams, …).
With the gear selector in position A , M or R,
the vehicle moves as soon as you take your
foot off the brake pedal , at low speed and
with the engine at idle.
When the engine is running, never leave
children in the vehicle without supervision.
The autonomous traction function may
be temporarily unavailable if the clutch
temperature is too high or the slope too
steep.
6
Driving

108
Automated mode
F Select position A.
You can change mode at any time by
moving the gear selector from A to M or
the other way round.
Moving vehicle, never select the neutral N .
The instrument cluster displays
AUTO
along with the gear engaged.
The gearbox is then operating in auto-active
mode, without any action on the part of the
driver. It continuously selects the most suitable
gear for adapted to the following parameters:
-
o

ptimisation fuel consumption,
-

t
he style of driving,
-

r
oad conditions,
-

v
ehicle load.
For optimum acceleration, when overtaking
another vehicle for example, press the
accelerator pedal fully down, beyond the point
of resistance.
Manual mode
F Select position M .
Moving vehicle, never select the neutral N .
You can change mode at any time by
moving the gear selector from M to A or
the other way round. The gears engaged appear in turn in
the instrument cluster.
The shift requests are taken into account only if
the engine speed allows.
It is not necessary to release the accelerator
when changing gear.
When braking or slowing down, the gearbox
changes down automatically to allow the
vehicle to accelerate in the correct gear.
Under full acceleration, unless the engine is
close to its maximum speed, gear upshift will
only take place when the driver operates the
gear selector.
Reverse gear
To engage reverse gear, the vehicle must be
immobilised with your foot on the brake pedal.
F
Sel
ect position R .
There is an audible signal upon
engagement of reverse.
At low speed, if reverse gear is requested, the
N indicator flashes and the gearbox goes into
neutral automatically.
To engage reverse, put the gear selector into
position N , then to position R .
Driving

109
Stopping the vehicle
Before switching off the engine, you can:
- m ove to position N to engage neutral,
or
-

l
eave the gear engaged; in this case, it will
not be possible to move the vehicle.
For all parking situations, you must apply
the parking brake to immobilise the
vehicle.
In case of immobilization of the vehicle,
engine running, absolutely put the gearbox
in neutral N .
Before working in the engine
compartment, ensure that the gear
selector is in neutral N and the parking
brake is applied.
Reinitialisation
Following disconnection of the battery, you
have to reinitialise the gearbox.
F
S
witch on the ignition.AUTO and - appear in the
instrument cluster.
F

Sel
ect position N .
F

P
ress the brake pedal.
F

W
ait for approximately 30 seconds until N
or a gear appears in the instrument cluster.
F

M
ove the gear selector to position A , then
to position N .
F

W
ith your foot still on the brake pedal, start
the engine.
The gearbox is operational again. Exceptionally, it may be necessary to
reinitialise the gearbox automatically: in
such a case the vehicle won't start and no
gear change will happen.
Malfunction
or
With the ignition on, if this warning
light comes on and AUTO
flashes,
accompanied by an audible signal
and a message in the multifunction
screen, this indicates a gearbox
fault.
Have them checked by a
CITROËN dealer or a
qualified workshop. AUTO
and - appear in the
instrument cluster.
Follow the procedure described above.
6
Driving

110
Automatic gearbox (EAT6)
Six-speed automatic gearbox which offers a
choice between the comfort of fully automatic
operation, enhanced by sport and snow
programmes, or manual gear changing.
Two driving modes are available:
-
a
utomatic operation for electronic
management of the gears by the gearbox,
with a spor t programme for a more
dynamic style of driving and a snow
programme to improve driving when
traction is poor,
-

man
ual operation for sequential changing
of the gears by the driver.
Gear box deck
1 Gear selector.
2 "S " (spor t) button.
3 "T " (snow) T button. (neige)
Gear selector positions
P.Parking.
-
I mmobilisation of the vehicle,
parking brake on or off.
-
S

tarting the engine.
R. Reverse.
-

R
eversing manoeuvres, vehicle
stationary, engine at idle.
N. Neutral.
-

I
mmobilisation of the vehicle,
parking brake on.
-
S

tarting the engine.
D. Automatic operation.
M + / -. Manual operation with sequential
changing of the six gears. F

P
ush for wards to change up through the
gears.
F
P
ull backwards to change down through
the gears.
or
Driving

111
Starting the vehicle
F Apply the parking brake.
F Sel ect position P or N .
F

S
tart the engine.
If these conditions are not met, there is an
audible signal, accompanied by the display of a
warning message.
F

W
ith the engine running, press the brake
pedal.
F

R
elease the parking brake.
F

Sel
ect position R , D or M.
F

G
radually release the brake pedal.
The vehicle moves off immediately. If position N is selected inadvertently while
driving, allow the engine to return to idle
then select position D before accelerating.
If the temperature is below -23°C, the
engine should be left at idle for four
minutes, to ensure the correct operation
and life of the engine and gearbox.
Displays in the instrument panel
When you move the selector to select a
position, the corresponding indicator is
displayed in the instrument panel.
P.
Parking.
R. Reverse.
N. Neutral.
D. Drive.
S. Sport programme.
T . Snow
programme.
1 2 3 4 5 6. Gears engaged during manual
operation.
-. Invalid value during manual
operation.
Foot on brake
F Press the brake pedal when this
indicator light is displayed in the
instrument panel (e.g.: starting
the engine).
When the engine is running at idle, with
the brakes released, if position R, D or
M is selected, the vehicle moves even
without the accelerator being pressed.
When the engine is running, never leave
children in the vehicle without supervision.
When carrying out maintenance with the
engine running, apply the parking brake
and select position P .
6
Driving

112
Automatic operation
F Select position D for automatic changing
of the six gears.
The gearbox then operates in auto-adaptive
mode, without any action needed from the
driver. It continuously selects the most suitable
gear according to the style of driving, the profile
of the road and the load in the vehicle.
To obtain maximum acceleration without
touching the selector, press the accelerator
pedal all the way down (kick down). The
gearbox changes down automatically or
maintains the gear selected until the maximum
engine speed is reached.
When braking, the gearbox changes down
automatically to provide effective engine
braking.
If you release the accelerator sharply, the
gearbox will not change to a higher gear for
safety reasons.
Never select position N while the vehicle
is moving.
Never select positions P or R unless the
vehicle is completely stationary.Reverse gear
When selecting reverse R with the ignition
on, the rear parking sensors are activated
automatically.
For more information on Rear parking
sensors , refer to the corresponding section.
Autonomous traction function
(moving without using the
accelerator)
This function facilitates manoeuvring of the
vehicle at low speed (when parking, in traffic
jams, …).
With the engine at idle, parking brake released
and position D , M or R selected, the vehicle
moves as soon as you take your foot off
the brake pedal (even without pressing the
accelerator).
Sport and snow
programmes
These two special programmes supplement the
automatic operation in very specific conditions
of use.
Sport programme "S"
F Press button S, after starting the engine.
The gearbox automatically favours a dynamic
style of driving.
S appears in the instrument panel.
Driving

114
Stopping the vehicle
Before switching off the engine, you can
engage position P or N to place the gearbox in
neutral.
In both cases, apply the parking brake to
immobilise the vehicle.If the selector is not in position P , when the
driver's door is opened or approximately
45 seconds after the ignition is switched
off, a warning message appears in the
screen.
F

R
eturn the selector to position P ; the
message disappears.
When driving on flooded roads or when
crossing a ford, proceed at walking pace.
Malfunction
or When the ignition is on, the lighting
of this warning light, accompanied
by an audible signal and a message
in the screen, indicates a gearbox
fault.
In this case, the gearbox goes into back-up
mode by staying in 3rd gear. You may feel a
substantial knock when changing from P to
R and from N to R . This will not cause any
damage to the gearbox.
Do not exceed 60 mph (100 km/h), local speed
restrictions permitting.
Contact a
CITROËN dealer or a qualified
workshop as soon as possible. There is a risk of damage to the gearbox:
-

i
f you press the accelerator and brake
pedals at the same time,
-
i
f you force the movement of the
selector from the P position to another
position when the battery is dead.
To reduce fuel consumption when at
a prolonged standstill with the engine
running (traffic jam, etc.), put the
selector in the N position and apply the
parking brake.
Driving