Citroen C4 PICASSO 2016 2.G Service Manual

39
C4-Picasso-II_en_Chap01_instruments-bord_ed01-2016
Resetting the service indicator
If you have to disconnect the battery
following  this   operation,   lock   the   vehicle  
a

nd wait at least 5 minutes for the reset
to
  be   registered.
After each service, the service indicator must
be
 
reset
 
to
 
zero.
If you have carried out the service on your
vehicle
 y

ourself:
F
 
s

witch
 
off
 
the
 
ignition,
F

p

ress and hold the trip distance recorder
reset button,
F
 
s

witch
 
o

n
 
t

he
 
i

gnition;
 
t

he
 
d

istance
 
r

ecorder
 
d

isplay
 
begins
 
a
 
countdown,
F

w

hen the display indicates "=0" , release
the
 
button;
 
the
 
spanner
 
disappears.
Retrieving the service
information
You can access the service information at any
time.
F
P
ress the trip distance recorder reset
button.
T

he service information is displayed for a
few
  seconds,   then   disappears.
1
Instruments

40
C4-Picasso-II_en_Chap01_instruments-bord_ed01-2016
* Only with the type 2 instrument panel.
Coolant temperature gauge*
After driving for a few minutes, the temperature and   pressure   in   the   cooling   system   increase.
To
  top-up   the   level:
F
 
w
ait   for   the   engine   to   cool,
F
 
u
nscrew   the   cap   slightly   to   allow   the  
p

ressure to drop,
F

w
hen the pressure has dropped, remove
the cap,
F
 
t
op-up   the   level   to   the   "MA X"   mark.
With
 
the
 
engine
 
running,
 
when
 
the
 
needle
 
is:
-

i

n zone A , the temperature is correct,
-

i

n zone B,
 
the
 
temperature
 
is
 
too
 
high;
 
t

he
 
maximum
 
temperature
 
and
 
the
 
c

entral STOP
 

warning
 
lamps
 
come
 
on,
 
a

ccompanied
 
by
 
an
 
audible
 
signal
 
and
 
a
 
w

arning
 m

essage. Be
  aware   of   the   risk   of   burns   when  
t

opping-up   the   cooling   system.   Do   not  
f

ill   above   the   maximum   level   (indicated  
o

n   the   header   tank).
You MUST stop as soon as it is safe
to do so.
Wait
 
a
 
few
 
minutes
 
before
 
switching
 
off
 
the
 
e

ngine.
Contact a CITROËN dealer or a qualified
workshop.
Instruments

41
C4-Picasso-II_en_Chap01_instruments-bord_ed01-2016
Engine oil level indicator*
On versions fitted with an electric oil level
indicator,  the   state   of   the   engine   oil   level   is  
d

isplayed in the instrument panel for a few
seconds,
  after   the   servicing   information.
The level read will only be correct if
the
  vehicle   is   on   level   ground   and   the  
e

ngine   has   been   off   for   more   than  
3

0 minutes.
Oil level correct
Oil level incorrect
This is indicated by the display of the message "Oil level incorrect" in the instrument panel
screen,
  accompanied   by   the   service   warning  
l

amp   and   an   audible   signal.
If
  the   low   oil   level   is   confirmed   by   a   check   using  
t

he   dipstick,   the   level   must   be   topped   up   to  
a

void   damage   to   the   engine.
For more information on Checking levels,
refer
  to   the   corresponding   section.
Oil level indicator fault
This is signalled by the display of the message "Oil level measurement invalid" in the
instrument
 pan

el.
Contact a CITROËN dealer or a qualified
workshop.
In the event of a fault with the electric indicator,
the
  oil   level   is   no   longer   monitored.
If
  the   system   is   faulty,   you   must   check   the  
e

ngine   oil   level   using   the   manual   dipstick  
l

ocated   under   the   bonnet.
For more information on Checking levels,
refer
  to   the   corresponding   section.
* Depending on version.
1
Instruments

42
C4-Picasso-II_en_Chap01_instruments-bord_ed01-2016
AdBlue® fluid range indicators
Once the AdBlue® tank is on reserve or after d
etection of a fault with the SCR emissions
control
 
system,
 
when   the   ignition   is   switched  
o

n, an indicator displays an estimate of the
distance
 
that
 
can
 
be   covered,   the   range,   before  
e

ngine
 
starting
 
is
 
prevented.
In the event of simultaneous system fault and
low AdBlue
® level, the shortest range figure is t
he
 
one
 
displayed. Range greater than 1 500 miles (2 400 km)
When
  the   ignition   is   switched   on,   no  
i

nformation   on   range   is   displayed   automatically  
i

n   the   instrument   panel.
With   the   type   2   instrument   panel,   pressing   this  
b

utton   temporarily   displays   the   driving   range.
In the event of the risk of non-starting related to a lack of AdBlue®
The engine start prevention system required   by   regulations   is   activated  
a

utomatically once the AdBlue
® tank is e
m pt y.
Instruments

43
C4-Picasso-II_en_Chap01_instruments-bord_ed01-2016
Remaining range between 350 and 1500 miles
(600 and 2 400 km)
When switching on the ignition, the AdBlue w arning   lamp   comes   on   for   a   few   seconds,  
a

ccompanied   by   an   audible   signal   and   the  
d

isplay   of   a   message   (e.g.:   "Top-up   AdBlue:  
S

tarting   impossible   in   900   miles")   indicating  
t

he   remaining   range   expressed   in   miles   or  
k

ilometres.
When
  driving,   the   message   is   displayed   every  
2

00   miles   (300   km)   until   the   fluid   level   has   been  
t

opped-up.
Go to a CITROËN dealer or a qualified
workshop
  to   have   the   AdBlue
® fluid topped-up.
Y
ou
 
can
 
also
 
top-up
 
the
 
fluid
 
yourself.
For more information on AdBlue
® and the SCR
system,
 
and
 
in
 
particular
 
on
 
topping-up,   refer  
t

o
 
the
 
corresponding
 
section. Remaining range between 0 and 350 miles
(0 and 600 km)
When
  switching   on   the   ignition,   the   SERVICE  
w

arning   lamp   comes   on   and   the   AdBlue  
w

arning   lamp   flashes,   accompanied   by   an  
a

udible   signal   and   the   display   of   a   message  
(

e.g.   "Top-up   AdBlue:   Starting   impossible   in  
3

50   miles")   indicating   the   remaining   range  
e

xpressed   in   miles   or   kilometres.
When   driving,   the   message   is   displayed   every  
3

0   seconds   until   the   fluid   level   has   been  
t

opped-up.
Go to a CITROËN dealer or a qualified
workshop   to   have   the   AdBlue
® fluid topped-up.
Y
ou
 
can
 
also
 
top-up
 
the
 
fluid
 
yourself.
Other wise you will not be able to restart your
engine. Breakdown related to a lack of AdBlue
®
When switching on the ignition, the SERVICE w
arning   lamp   comes   on   and   the   AdBlue  
w

arning   lamp   flashes,   accompanied   by   an  
a

udible   signal   and   the   display   of   a   message  
(

e.g.   "Top-up   AdBlue:   Starting   impossible").
The AdBlue
® tank  is  empty:  t he  s ystem  r equired  b
y
 
regulations   prevents   engine   starting.
To
 
be
 
able   to   start   the   engine,  
w

e recommend that you call on
a CITROËN dealer or a qualified
workshop
  for   the   top-up   required.
If you carry out the top-up yourself, it
is
 
essential   to   add   at   least   3.8   litres   of  
Ad

Blue
® to the tank.
F
or more information on AdBlue® and the SCR
system,
 
and
 
in
 
particular
 
on
 
topping-up,   refer  
t

o
 
the
 
corresponding
 
section.
1
Instruments

44
C4-Picasso-II_en_Chap01_instruments-bord_ed01-2016
In the event of a fault with the SCR emissions control system
In the event of the detection of a fault
The  AdBlue,   SERVICE   and   diagnostic  
w

arning   lamps   come   on,   accompanied   by   an  
a

udible   signal   and   the   display   of   the   message  
"

Emissions
 f
ault".
The
  alert   is   triggered   when   driving   when   the  
f

ault is detected for the first time, then when
switching
  on   the   ignition   for   subsequent  
j

ourneys,   while   the   fault   persists. During an authorised driving phase (between
650 miles and 0 miles) (1 100 km and 0 km)
If a fault with the SCR system is confirmed
(after
  30   miles   (50   km)   covered   with   the  
p

ermanent   display   of   the   message   signalling  
a

  fault),   the   SERVICE   and   engine   diagnostic  
w

arning   lamps   come   on   and   the   AdBlue  
w

arning   lamp   flashes,   accompanied   by   an  
a

udible   signal   and   the   display   of   a   message  
(

e.g.   "Emissions   fault:   Starting   prevented   in  
1

50   miles")   indicating   the   remaining   range  
e

xpressed   in   miles   or   kilometres.
While
  driving,   the   message   is   displayed   every
 3

0   seconds   while   the   fault   with   the   SCR   system
 p

ersists.
The alert is repeated when switching on the ignition.You should go to a CITROËN dealer or a qualified   workshop   as   soon   as   possible.
Other wise, you will not be able to restart your
engine.
A
 
system
 
that
 
prevents
 
engine
 
starting
 
is
 
activated   automatically   from   650   miles   (1   100   km)   after   confirmation   of   a   fault   with   the   SCR   emissions  
c

ontrol
 
system.
 
Have
 
the
 
system
 
checked
 
by
 
a   CITROËN   dealer   or   a   qualified   workshop   as   soon   as   possible.
If it is a temporary fault, the alert
disappears
 
during
 
the
 
next
 
journey,
 a
fter
 
self-diagnosis
 
of
 
the
 
SCR
 
system. Starting prevented
Every
  time   the   ignition   is   switched   on,   the  
S

ERVICE   and   engine   diagnostic   warning  
l

amps   come   on   and   the   AdBlue   warning   lamp  
f

lashes,   accompanied   by   an   audible   signal   and  
t

he   display   of   the   message   "Emissions   fault:  
St

arting
 p
revented".
You   have   exceeded   the   authorised  
d

riving   limit:   the   starting   prevention  
s

ystem   inhibits   engine   starting.
To   be   able   to   start   the   engine,   you   must  
c

all on a CITROËN dealer or a qualified
workshop.
Instruments

45
C4-Picasso-II_en_Chap01_instruments-bord_ed01-2016
Distance recorders
The total and trip distances are displayed for
thirty  seconds   when   the   ignition   is   switched   off,  
w

hen   the   driver's   door   is   opened   and   when   the  
v

ehicle   is   locked   or   unlocked.
When
  travelling   abroad,   you   may  
h

ave   to   change   the   units   of   distance:  
t

he display of road speed must be in
the
  official   units   (miles   or   km)   for   the  
c

ountry.   The   change   of   units   is   done   via  
t

he   screen   configuration   menu,   with   the  
v

ehicle   stationary.
Trip distance recorder
It measures the distance travelled since it was
reset  to   zero   by   the   driver.
F
 
W
ith   the   ignition   on,   press   the   button   until  
z

eros   appear.
Total distance recorder
It measures the total distance travelled by the
vehicle  since   its   first   registration.
1
Instruments

46
C4-Picasso-II_en_Chap01_instruments-bord_ed01-2016
Lighting dimmer control
Allows the manual adjustment of the brightness of the instrument panel and touch screen tablet to suit   the   ambient   light   level.
Operates
  only   when   the   vehicle   lighting   is   on,   with   the   exception   of   the   daytime   running   lamps.
Tw o b u t t o n s
With the exterior lighting on, press button A
t o   increase   the   brightness   of   the   instruments  
a

nd   controls   and   the   interior   mood   lighting   or  
b

utton B   to   reduce   it.
As
  soon   as   the   lighting   reaches   the   required  
l

evel   of   brightness,   release   the   button.
Touch screen tablet
F In the Configuration menu, select
" Brightness ".
F
 
A
djust   the   brightness   using   the   arrows   or  
b

y   moving   the   cursor.
Instruments

47
C4-Picasso-II_en_Chap01_instruments-bord_ed01-2016
When driving at night, this function allows certain displays in the instrument panel to be
switched
  off   to   avoid   visual   fatigue   for   the   driver.
The essential information, such as the speed of
the vehicle or the cruise control or speed limiter
indications remains displayed in the instrument
panel.
Using the steering mounted
control
F With   the   vehicle   lighting   on,   press   this  b
utton   again   to   activate   the   black   panel.
F
 
P
ress   this   button   again   to   deactivate   it.
Black screen (touch screen
tablet)
Black panel (comfortable
night driving display)
F In the Configuration
menu, select "Dark". T
he   screen   of   the   touch   screen   tablet   goes  
o

f f.
 F

 
P
ress   the   screen   again   (anywhere   on   its  
s

ur face)   to   switch   it   on   again.
1
Instruments

48
C4-Picasso-II_en_Chap01_instruments-bord_ed01-2016
Tr i p c o m p u t e r
Type 1 instrument panel
System that gives you information on the journey in progress (range, fuel consumption…).
Information display in the touch screen tablet
Permanent display:
F Sel ect the " Trip computer " in the
Applications
 

menu.
The trip computer information is displayed in
tabs.
F

P
ress one of the buttons to display the
desired
 t

ab. The
  current   fuel   consumption   tab   with:
-  
t
he   range,
-
t
he current fuel consumption,
-  
t
he   Stop   &   Start   time   counter.
The trip "1"
 
tab   with:
-
t
he distance travelled,
-  
t
he   average   fuel   consumption,
-  
t
he   average   speed,  
 
f
or   the   first   trip.
The trip "2"  tab   with:
-

t
he distance travelled,
-
 
t
he   average   fuel   consumption,
-
 
t
he   average   speed,  
 
f

or   the   second   trip.
Trip reset
F When the desired trip is displayed, press the reset button or on the end of the wiper
control
  stalk.
Tr i p s "1" and "2" are independent but their use
is
  identical.
For
  example,   trip   "1" can be used for daily
figures,
  and   trip   "2"
 
for   monthly   figures.
The information is accessible in the Driving
 

menu.
Temporary
 
display
 
in
 
a
 
new
 
window:
F
 
P

ress
 
the
 
end
 
of
 
the
 
wiper
 
control
 
stalk
 
for
 
a

ccess to the information and display the
different
 
tabs.
Instruments