Citroen C5 2008.5 (RD/TD) / 2.G Owner's Manual
Manufacturer: CITROEN, Model Year: 2008.5, Model line: C5, Model: Citroen C5 2008.5 (RD/TD) / 2.GPages: 306, PDF Size: 18.9 MB
Page 161 of 306
161
11
P R A C T I C A L I N F O R M A T I O N
PUNCTURE REPAIR KIT Using the kit
The puncture repair kit is located in
t h e b o o t u n d e r t h e fl o o r .
Switch off the ignition.
A f fi x t h e s p e e d l i m i t a t i o n s t i c k e r
to the vehicle’s steering wheel
to remind you that a wheel is in
temporary use.
Check that the switch A is in po-
sition "0" .
Connect the pipe of the bottle 1
to the valve of the tyre to be re-
paired.
Connect the compressor’s elec-
tric plug to the vehicle’s 12 V
socket.
Start the vehicle and leave the
engine running.
Complete system consisting of a
compressor and a bottle of sealant
product which permits
temporary
repair of the tyre so that you can
drive to the nearest garage.
This repair kit is available from
CITROËN dealers.
It is designed to repair holes of a
m a x i m u m d i a m e t e r o f 6 m m , l o c a t -
e d e x c l u s i v e l y o n t h e t y r e t r e a d o r
shoulder. Avoid removing any for-
eign bodies which have penetrated
the tyre.
Page 162 of 306
162
11
P R A C T I C A L I N F O R M A T I O N
Remove the compressor and
unclip and store the bottle in a
sealed bag to avoid staining your
v e h i c l e w i t h t r a c e s o f fl u i d .
D r i v e i m m e d i a t e l y f o r a p p r o x i -
mately two miles (three kilome-
tres), at reduced speed (between
15 and 35 mph [20 and 60 km/h]),
to plug the puncture.
Stop to check the repair and the
pressure.
Connect the compressor pipe di-
rectly to the valve of the repaired
wheel.
Switch on the compressor by
moving the switch A to posi-
tion "1" until the tyre pressure
reaches 2.0 bars. If this pressure has not
b e e n r e a c h e d a f t e r a p p r o x i -
m a t e l y fi v e t o t e n m i n u t e s ,
the tyre cannot be repaired; contact
a CITROËN dealer to have your ve-
hicle repaired.
Page 163 of 306
163
P R A C T I C A L I N F O R M A T I O N
Connect the compressor’s elec-
tric plug to the vehicle’s 12 V
socket again.
Start the vehicle again and leave
the engine running.
Adjust the pressure using the
c o m p r e s s o r ( t o i n fl a t e : s w i t c h A
in position "1" ; t o d e fl a t e :
switch A in position "0" and
press button B ), in accordance
with the vehicle’s tyre pressure
label (located on the door aper-
ture on the left-hand side), then
remember to check that the leak
has been plugged correctly (no
further loss of pressure after
several miles [kilometres]).
Remove the compressor, then
store the whole kit.
Drive at reduced speed (50 mph
[ 8 0 k m / h ] m a x ) l i m i t i n g t h e d i s -
t a n c e t r a v e l l e d t o a p p r o x i m a t e l y
120 miles (200 km).
Visit a CITROËN dealer as soon
as possible to have the tyre re-
paired or replaced by a techni-
cian. Take care, the bottle of
p u n c t u r e r e p a i r fl u i d c o n -
tains ethylene-glycol. This
product is harmful if swallowed and
causes irritation to the eyes. Keep
it out of reach of children.
T h e e x p i r y d a t e o f t h e fl u i d i s i n d i -
cated on the base of the bottle.
The bottle is designed for a sin-
gle use; even if only partly used, it
must be replaced.
After use, do not discard the bottle
into the environment, take it to an
authorised waste disposal site.
Do not forget to obtain a new
bottle of sealant, available from
CITROËN dealers.
I f t h e v e h i c l e i s fi t t e d w i t h t y r e u n d e r -
i n fl a t i o n d e t e c t i o n , t h e t y r e u n d e r -
i n fl a t i o n w a r n i n g l a m p w i l l r e m a i n o n
after the wheel has been repaired
until the system is reinitialised by a
CITROËN dealer.
Page 164 of 306
164
11
P R A C T I C A L I N F O R M A T I O N
CHANGING A WHEEL
Access to the tools
The tools are to be found in a protec-
tive holder inside the spare wheel.
Pull back the retaining strap for
access. List of tools
1. Wheelbrace
2. Jack
3. T o o l f o r t h e r e m o v a l / r e fi t t i n g o f
bolt protectors
4. Centring guide
5. Towing eye
6. Moveable chock (depending on
equipment)
Page 165 of 306
165
11
P R A C T I C A L I N F O R M A T I O N
Access to the spare wheel
To remove the spare wheel
L i f t u p t h e b o o t fl o o r u s i n g t h e
strap (Saloon) or the retractable
handle (Tourer).
Fold back the boot carpet
(Saloon).
Attach the hook to the top of the
boot.
Detach the strap then push the
wheel forwards so as to be able
to lift it. To reposition the spare wheel
P o s i t i o n t h e s p a r e w h e e l fl a t i n
the boot, then pull it towards
you.
N e x t p l a c e t h e t o o l b o x i n s i d e t h e
wheel, then secure the assembly
with the belt.
Release the strap to return the
b o o t fl o o r t o i t s i n i t i a l p o s i t i o n . The tyre pressure is indi-
cated on the label located
on the left-hand door centre
pillar. On this label, the pressures
a r e s p e c i fi e d , a c c o r d i n g t o t h e v e -
hicle load.
Page 166 of 306
166
P R A C T I C A L I N F O R M A T I O N
Removing a wheel
P a r k t h e v e h i c l e o n s t a b l e , fi r m
ground that is not slippery. apply
the parking brake.
If your vehicle is equipped with
"Hydractive III+" suspension,
with the engine running at idle,
adjust the ground clearance to
i t s m a x i m u m h e i g h t .
Switch off the ignition and en-
g a g e fi r s t g e a r o r r e v e r s e g e a r
depending on any slope (for a
v e h i c l e w i t h a u t o m a t i c g e a r b o x ,
select position P).
I f y o u r v e h i c l e i s fi t t e d w i t h
"Hydractive III+" suspension,
position the chock, whichever di-
rection the gradient may be in, in
front of the front wheel diametri-
cally opposite to the one to be
replaced.
Position the jack at one of the
four jacking-points provided
on the underbody close to the
wheels, then use the wheelbrace
to unwind the jack until it reaches
the ground.
Remove the protector from each
bolt using tool 3 .
Slacken the wheel bolts.
Before positioning the
jack:
Always adjust the vehicle’s
g r o u n d c l e a r a n c e t o t h e " m a x i -
mum height" position and re-
tain this adjustment for as long
as the jack is under the vehi-
cle (do not use the hydraulic
adjustments),
Immobilise your vehicle on hori-
zontal, stable and non-slippery
ground,
Ensure that any passengers
have left the vehicle and are in
a safe place .
Never get underneath the vehicle if
it is supported only by the jack.
The jack and all of the tools are
s p e c i fi c t o y o u r v e h i c l e . D o n o t u s e
them for any other applications.
Have the original wheel repaired
a n d r e fi t t e d a s s o o n a s p o s s i b l e .
C o n t i n u e t o e x t e n d t h e j a c k u n t i l
the wheel is a few centimetres
off the ground.
Undo the bolts, remove the
wheel.
Page 167 of 306
167
11
P R A C T I C A L I N F O R M A T I O N
Wheel for temporary use
Y o u r v e h i c l e m a y b e fi t t e d w i t h a
spare wheel which is different to
t h o s e o n t h e v e h i c l e . W h e n fi t t i n g
the spare wheel, it is normal to no-
tice that the wheel bolt washers do
not come into contact with the wheel
rim. The spare wheel is secured by
the conical tapering of the wheel
bolt’s shaft.
W h e n r e fi t t i n g t h e o r i g i n a l w h e e l ,
ensure that the wheel bolt contact
surfaces are clean and in good con-
dition. Fitting a wheel
Fit the wheel on the hub, using
the centring guide. Make sure
that the contact surface between
the hub and the wheel is clean.
Screw in the bolts but do not fully
tighten them.
Lower the jack and remove it.
Tighten the wheel bolts, using
the wheelbrace.
R e fi t t h e p r o t e c t o r s o n t h e b o l t s .
Return the ground clearance to
the normal position.
Ensure the tyre pressure is cor-
rect and have the balancing
checked.
Deflation detection
These wheels have tyre pressure
sensors. It is essential to have re-
pairs carried out by a CITROËN
dealer.
Anti-theft bolts
Each wheel is equipped with one
anti-theft bolt.
To remove it:
Remove the protector using tool 3 .
Use the anti-theft socket with the
wheelbrace. I f y o u r v e h i c l e i s fi t t e d w i t h
a spare wheel of a different
size to those on the vehi-
c l e , y o u m u s t n o t e x c e e d 5 0 m p h
(80 km/h) whilst using the spare
wheel.
T h e w h e e l b o l t s a r e s p e c i fi c t o t h e
type of wheel.
If the type of wheel is changed,
check with your CITROËN dealer
that the wheel bolts are compatible
with the new wheels.
Take care to note down the code
number engraved on the head of
the anti-theft bolt socket. This will
enable you to obtain a replace-
ment anti-theft bolt socket from a
CITROËN dealer .
Page 168 of 306
167
11
P R A C T I C A L I N F O R M A T I O N
Wheel for temporary use
Y o u r v e h i c l e m a y b e fi t t e d w i t h a
spare wheel which is different to
t h o s e o n t h e v e h i c l e . W h e n fi t t i n g
the spare wheel, it is normal to no-
tice that the wheel bolt washers do
not come into contact with the wheel
rim. The spare wheel is secured by
the conical tapering of the wheel
bolt’s shaft.
W h e n r e fi t t i n g t h e o r i g i n a l w h e e l ,
ensure that the wheel bolt contact
surfaces are clean and in good con-
dition. Fitting a wheel
Fit the wheel on the hub, using
the centring guide. Make sure
that the contact surface between
the hub and the wheel is clean.
Screw in the bolts but do not fully
tighten them.
Lower the jack and remove it.
Tighten the wheel bolts, using
the wheelbrace.
R e fi t t h e p r o t e c t o r s o n t h e b o l t s .
Return the ground clearance to
the normal position.
Ensure the tyre pressure is cor-
rect and have the balancing
checked.
Deflation detection
These wheels have tyre pressure
sensors. It is essential to have re-
pairs carried out by a CITROËN
dealer.
Anti-theft bolts
Each wheel is equipped with one
anti-theft bolt.
To remove it:
Remove the protector using tool 3 .
Use the anti-theft socket with the
wheelbrace. I f y o u r v e h i c l e i s fi t t e d w i t h
a spare wheel of a different
size to those on the vehi-
c l e , y o u m u s t n o t e x c e e d 5 0 m p h
(80 km/h) whilst using the spare
wheel.
T h e w h e e l b o l t s a r e s p e c i fi c t o t h e
type of wheel.
If the type of wheel is changed,
check with your CITROËN dealer
that the wheel bolts are compatible
with the new wheels.
Take care to note down the code
number engraved on the head of
the anti-theft bolt socket. This will
enable you to obtain a replace-
ment anti-theft bolt socket from a
CITROËN dealer .
Page 169 of 306
168
P R A C T I C A L I N F O R M A T I O N
CHANGING A BULB
Procedure for replacing a faulty bulb
with a new bulb without the use of
any tools.
Headlamps
Model with Xenon headlamps
(D1S)
1. Sidelamps: W 5 W
2. Dual-function Xenon
headlamps (dipped/main): D1S
3. Angular lighting: HP19
4. Daytime-running lamps: HP24 Sidelamps
Lift up the pegs A to remove the
cover on the headlamp.
Remove the protective cap B .
Pull the bulb holder to remove it.
R e p l a c e t h e b u l b a n d r e fi t t h e
bulb holder.
For the maintenance of the front
headlamp unit and the changing of
HP19, D1S and HP24 bulbs, contact
a CITROËN dealer.
Risk of electrocution
Xenon bulbs must be re-
placed by a CITROËN
dealer.
You are advised to change both
D1S bulbs at the same time, if one
of them has failed.
R e fi t t h e p r o t e c t i v e c a p B .
R e fi t t h e c o v e r a n d fi x i t i n p l a c e
using the pegs A .
Page 170 of 306
169
11
P R A C T I C A L I N F O R M A T I O N Main beams Sidelamps
Lift up the pegs A to remove the
cover on the headlamp.
Remove the protective cap B .
Disengage the retaining spring.
Remove the bulb and replace it,
paying attention to the direction
o f fi t t i n g .
R e fi t t h e r e t a i n i n g s p r i n g .
R e fi t t h e p r o t e c t i v e c a p B .
R e fi t t h e c o v e r a n d fi x i t i n p l a c e
using the pegs A .
Lift up the pegs A to remove the
cover on the headlamp.
Remove the protective cap B .
Pull the bulb holder to remove it.
R e p l a c e t h e b u l b a n d r e fi t t h e
bulb holder.
R e fi t t h e p r o t e c t i v e c a p B .
R e fi t t h e c o v e r a n d fi x i t i n p l a c e
using the pegs A .
Model with halogen headlamps
1. Main beams: H1
2. Sidelamps: W 5 W
3. Dipped beams: H7
4. Directional lighting: H7
5. Daytime-running lamps: HP24
For the maintenance of the front
headlamp unit and changing HP24
bulbs, contact a CITROËN dealer.
Halogen bulbs must not be changed
until they have been off for a few
minutes (risk of serious burns).
Do not touch the bulb directly with
y o u r fi n g e r s , u s e a l i n t - f r e e c l o t h .
It is essential that only anti-U.V.
type bulbs are used in order not to
damage the headlamp.