DACIA SOLENZA 2004 Repair Manual

84
STEERING - CONN ECTOR
84 - 6
Connector
Pin Denomination
1 Rear window defrosting indicator
2 Defrosting control
3 Supply + after contact
4 Mass
5 Supply + parking
Rear windows defrosting switch
15
vnx.su

84
STEERING - CONN ECTOR
84 - 7
Connector
Pin Denomination
1 Doors blocking control
2 Supply + parking
3 Mass
4 Mass
5 Doors unlocking control
Central locking switch
vnx.su

84
STEERING - CONN ECTOR
84 - 8
Connector
Pin Denomination
1 Passenger window lowering
2 Mass
3 Supply + after contact
4 Supply + parking
5 Passenger window lifting
Passenge r ele ctric w indow switch
vnx.su

84
STEERING - CONN ECTOR
84 - 9
Connector
Pin Denomination
1Dr iver window lowering
2 Mass
3 Supply + after contact
4 Supply + parking
5 Driv er window liftin g
Driver electric window switch
vnx.su

84
STEERING - CONN ECTOR
84 - 10
Connector
Pin Denomination
1 Supply + parking
2 Control + signaling relay
3 Left turning lights control
4 Right turning lights control
5 Mass
6+ Battery
7+ A ccessories
8 Control + signalin g
Hazard switch
vnx.su

84
STEERING - CONN ECTOR
84 - 11
DISMOUNTIN G
Disconnect the battery (-) terminal.
Dismount the upper part dashboard.
Disconnect connectors ( 1), (2) and (3). Mark identification of their mounting position.
Holding with one hand the fix part ( 4) dismount the lighter attachment clamp ( 5) on the lower
part dashboard. Extract the lighter fix body (part).
REMOU NT I NG
Position the lighter fix body in the dashboard lower part. Holding with one hand the fix body,
mount the lighter attachmen t clamp. The required tightening moment is 1.5 Nm applied to the fix
body (4). Connect the lighter connectors, observing their mounting position existent prior to dismount-
ing. Mount the upper part dashboard.
Reconnect the battery (-) terminal.
Check the operation of the electric lighter.
REMARK:
In order to replace the bulb, dismount the lighter, dismount the bulb holder (6) from
the clamp (5) and replace the bulb.
Connectors
Connector Denomination 1 Mass
2 Supply + after contact
3 Supply + parking
Electric lighter
vnx.su

85
WINDSCR EEN WIPER
85 - 1
The drive mechanism is mounted in the cli-
mate control box.
DISMOUNTIN G
Ensure that assembly is stopped in the
position “ stopped at fix point”. Disconnect the battery (-) terminal.
Dismount the climate control gasket.
Dismount the climate control protector
Dismoun t the wiring connector ( 1) from the
windscreen wiper electric motor (push on the
connector A point and detach from clips).
Remove the protectors ( 2) from shafts.
Di smount the attachment nuts ( 3) of the
windscreen wiper blade-arm assemblies .
Dismount the windscreen wiper blade-arm
assemblies (4 ). Mark the identification of their
mounting position and of the two windscreen
wiper blade-arm assemblies (left-right).
Remove the covers ( 5). Di
smount the shafts attachment nuts ( 6) on
the windscreen lower frame; recover the washers
and gaskets.
Detach from clips the washing hose.
Dismount the mechanism attachment screw
(7) on the windscreen lower crossbeam.
Extract t he m echanism from the climate
control box, by rotating it.
REMOU NT I NG
Perform the dismounting operations in t he
reverse order.
REMARK:
When mounting the drive m echanism, t he
wiper e lectric motor must be in the position
”stopped at fix point”.
The re quir ed tight ening moment of the
mechanism attachment screw ( 7) on t he
w indscreen lower crossbeam : 6-8 Nm.
The required tightening moment of the shafts
attachment nuts ( 6) on the windscreen lower
crossbeam: 8 ± 15 % Nm.
The re quir ed tight ening moment of the
attachment nuts ( 3) of the windscreen wiper
blades a nd arm s : 12 ± 15% Nm.
The re quir ed tight ening moment of the
attachment screw (7) of the windscreen washing
assembly : 2 Nm.
Drive mechanism
vnx.su

WINDSCR EEN WIPER
85
85 - 2
Connector
1
5
Drive mechanism
Pin Denomination
1 Mass
2 Stopping at fix point
3+ Battery
4 Low speed control
5 High speed control
vnx.su

85
WINDSCR EEN WIPER
85 - 3
Replace
fuse F 07 Check fuse F07 from cockpit.
Is it good?
Replace the under steering wheel control assembly .
Replace the windscreen wiper timer. Check the windscreen wiper
switch. Is it good?
Check the windscreen wiper timer. Is i t good?
Replace the windscreen
wiper electric motor.. Is there any 12 V between pins 5
and 1 of the electric
motor connector
of the windscreen wiper ? S
et the contact on. Switch the
windscreen wiper on highs peed. Is the windscreen
wiper working?
Set the contact off.
Check the continuity and the resistance against the vehicle mass
betw een:
- exit fu se F07 pin A7 windscreen wiper switch
- pin A2 windscreen wi per switch pin 5 electric motor
connector of the windscreen wiper;
- pin 1 electric motor connector of the windscreen wiper
ve hicle mass.
Are they good?
Defective wiring. Fix it.
Replace the windscreen
electric motor. Is there any 12 V between pins 4 and
1 of the electric motor connector of
the windscreen wiper?
S et the contact off.
Check the continuity and the resistance against the vehicle
mass between:
- exit fuse F07 pin A7 windscreen wiper switch
- pin A3 windscreen wiper switch pin 4 electri c motor
connector of the windscreen wiper;
- pin 1 electric motor connector of the windscreen wiper
vehicle mass. Are they good? Switch
the windscreen wiper
on low speed. Is the
windscreen wiper working ?
Defective wiring. Fix it.
No
NoNo
No
No
No
No No
No Ye s
Ye s
Ye s
Ye s
Da
1
Ye s Ye s
Diag nostic
vnx.su

WINDSCR EEN WIPER
85
85 - 4
S
et the contact off.
Check the continuity and the resistance against vehicle mass
between:
- exit fuse F02 pin 3 electric m otor c onnector of the
windscreen wiper
- pin 2 electric m otor connector of t he windscreen wiper pin 4
timer connector of the windscreen wiper;
- pin 3 timer connector of the windscreen wiper pin 6 switch
connector of the windscreen wiper.
Ar e they good?
Defective wiring. Fix it.
Replace the windscreen wiper timer. Is there any 12 V between
pins 9 and 1 of the timer connector of the
windscreen wiper
?
S et the contact off.
Check the continuity and the resistance against vehicle mass between:
- exit fuse F07 pin A7 switch connector of the windscreen wiper;
- pin A1 switch connector of the windscreen wiper pin 9 timer
connector of the windscreen wiper;
- pin 1 timer c onnector of the windscreen wiper vehicle m ass;
- pin 5 timer connector of the windscreen wiper exit fuse F 07.
Ar e they good ?
Defective wiring. Fix it.
Replace the windscreen washing reservoir. Is there any 12 V between pins 1 and
2 of the electri c pump connector of
the windscreen washing?
S et the contact off.
Check the continuity and resistance against vehicle mass between:
- exit fuse F07 pin B4 of the switch connector of the windscreen
wiper.
- pin A4 switch connector of the windscre en wiper pi n 2 e lectric
pump connector of the windscreen washing;
- pin A4 switch connector of the windscre en wiper pin 2 timer
connector of the windscreen wiper;
- pin 1 electric pump connector of the windscreen washing vehicle
mass;
- pin 5 timer connector of the windscreen wiper exit fuse F07.
Ar e they good? Electromotorul
º tergãtor parbriz
“se opreºte l a punct
fix”?
Switch the windscreen wiper
on timer position.
Is the windscreen wiper electric motor working delayed?
Switch the windscreen
wiper on windscreen
washing position. Is the
windscreen washing
electric pump working?
Cablajul
este defect.
Rem edi a πi.
1
No
No
No No
No
No
No
No
Ye s
Ye s Ye sYe s
Diag nostic
vnx.su