DACIA SOLENZA 2004 Repair Manual

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 21
ET309
ET310RIGHT TURNING INFORMATION
LEFT TURNING INFORMATION
Diagnostic – States interpretation
No failure must be present or memorized.
RECOMMENDATIONS Set on the contact Act upon the left or right turning control
State must be ACTIVE
Check the supply fuse F13 (25A) for turning lights/Cockpit Central
Unit.
Replace it if necessary.
Check connection and condition of the turning switch connector.
Fix is necessary.
Ensure continuity of the connection:
Turning switch pi n 6 mass
Fix if necessary
Di sconnect connector EH1 40 pins of UCH
Ensure continuity and insulation of the connections:
Right turning switch pin 5
pin B28 connector
EH1 40 pins UCH
Left turning switch pin 7
pin B26 connector
EH1 40 pins UCH
Fix is necessary.
Perform again a system diagnostic
Repair the other possible failures
Erase the memorized failures.
AFTER REPARATION
ET309
ar
ET310
INACTIVE
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 22
Diagnostic – States interpretation
ET213WINDSCREEN WIPER TIMER
RECOMMENDATIONS No failure must be present or memorized. Set on the contact
Act upon the left or right turning control
State must be ACTIVE
Check the windscreen wiper fuse F07 (20A).
Replace it if necessary.
Check the connection and condition of windscreen wiper switch connector
Fix the connector if necessary.
Ensure continuity and insulation of the connections:
connector EH1 of UCH
pin B24 wiper switch pin A1
+ after contact wiper switch pin A7
Fix if necessary.
ET213
INACTIVE
Perform again a system diagnostic
Repair the other possible failures
Erase the memorized failures.
AFTER REPARATION
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 23
Diagnostic – States interpretation
ET192FRONT DOORS
RECOMMENDATIONS Check that no failure is be present or memorized.Open the drivers’ door
Check that for open door the corresponding state is active or for closed door, the
corresponding state is inactive
Check continuity and insulation of the wiring between:
Dr iver’s doors contact and pin 40B of UCH connector EH1
Fix if necessary (see electric diagram of that vehicle)
O pen the door.
Check continuity between mass and pin 40B of UCH
Close the door and check that no continuity is between mass and pin 40B of UCH
In case of a failure, replace the driver’s door contact.
Perform again a system diagnostic
Repair the other possible failures
Erase the memorized failures.
AFTER REPARATION
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 24
Diagnostic – States interpretation
ET193RECEIVED INFORMATION
RECOMMENDATIONSOnly for “N4” Cockpit Central Unit.
Check that no failure is present
State is declared YES when pushing the remote control
If state i s declared NO, set on then set off the contact.
Try again with another key of the vehicle.
ET193 remains at NO : when pushing the remote c ontrol
Push the remote control button of some other vehicle of same type or with a new key:
Check that state is becoming YES, when pushing the remote control.
If state is YES , replace t he remote control of the breakdown vehicle.
If state is NO, replace the Cockpit Central Unit
Perform again a system diagnostic
Repair the other possible failures
Erase the memorized failures.
AFTER REPARATION
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 25
Diagnostic – States interpretation
ET257PARKING LIGHTS INFORMATION
RECOMMENDATIONS Check that no failure is present or memorized. Act upon the parking lights control.
State must be ACTIVE, and the parking lights on
Check the bulbs.
Check parking lights fuse F14 (7.5 A)
Replace it if necessary
Check connection and c ondition of UCH connector EH1 40 pins .
Replace the connector if necessary
Ensure continuity and insulation of the connection:
pin A15 connector EH1 40 pin sfuse box, parking
lights fuse (7.5A)
Fix if necessary.
ET257
INACTIV
Perform again a system diagnostic
Repair the other possible failures
Erase the memorized failures.
AFTER REPARATION
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 26
Diagnostic – Damage location algorithm
RECOMMENDATIONSDo not consult these information but after a complete
checking by means of CLIP te ster
THERE IS NO COMMUNI CATION WITH THE COMPUT ER AL P1
LIGHTING
TURNING LIGHTS ARE NOT WORKING AL P2
PARKING LIGHTS ARE NOT WORKING AL P3
WINDSCREEN WIPING WINDSCREEN WIPER L OW SPEED NOT WORKING AL P4
WINDSCREEN WI PER HIGH SPEED NOT WORKING AL P5
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 27
Diagnostic – Damage location algorithm
RECOMMENDATIONSNothing to notice
Check the tester operation on another vehicle
Check: - Connection between CLIP tester and the diagnostic socket (cable i n good condition).
- Cockpit and engine compartment fuses.
Check presence +12 volts before c ontact at pin 16 , + 12 volts after contact at pin 1
and mass at pins 4 and 5 of the di agnostic socket
Fix if necessary
Check the computer connection.
Connect the m ulti-socket and c heck the insulation, continuity and absence of parasite
resistance at connections: UCH connector P1 pin A1 mass
UCH connector P1 pin A3 fuse box + 12 volts before contact
UCH connector EH1 pin B34 pin 7 diagnostic socket (line K)
Fix if necessary.
.
ALP 1There is no communication with the computer
Check the system operation
AFTER REPAIRING
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 28
Diagnostic – Damage location algorithm
ALP 2Turning lights not working
RECOMMENDATIONS Do not consult these information but before a complete
checking by means of the CLIP tester.
Check the bulbs
Check the condition of fuse F13 (25A) and replace it i f necessary.
Pu sh the hazard switch and check that state <> is
ACTIVE ; if not, refer to chapter dealing with this state.
Act upon the right or left turning lights and check that state right turning information ET309 and
state left turning information ET310 are ACTIVE, if not, refer to the corresponding chapter of
these states.
Check the condition of connector P1 with 15 pins of Cockpit Central Unit
Replace it if necessary.
Ensure continuity of connections :
UC H connector P1 pin A9 left turning lamp
UC H connector P1 pin A8 right turning lamp
Fix if necessary.
Check the system operation
AFTER REPAIRING
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 29
Diagnostic – Damage location algorithm
RECOMMENDATIONSDo not consult these information but before a complete
checking by means of the CL IP tester.
Check the bulbs
Check the condition of parking lights fuse F14 (7.5A)
Replace it if necessary.
Act upon the parking lights control and check that state parking lights information ET257 is
ACTIVE , if not, refer to the corresponding chapter of these state.
Check the continuity of the connection:
Parking lights fuse F14 (7.5A) rear and front parking lights
Fix if necessary.
ALP 3Parki ng lights not working
Check the system operation
AFTER REPAIRING
vnx.su

87
ELECTRICAL ASSISANCE EQUIPEMENT
87 - 30
Diagnostic – Damage location algorithm
ALP 4Windscreen wiper low speed n ot working
RECOMMENDATIONS No failure must present or memorized
Check the condition of windscreen wiper fuse F07 (20A)
Replace the fuse if necessary.
Check supply +12 volts after contact at pin A7 windscreen wiper switch
Fix if necessary
Ensure the continuity and insulation of the connections:
Wiper switch pin A3 pin 4 windscreen wiper motor
Mass pin 1 windscreen wiper motor
Fix if necessary.
Check the motor operation
Check that windscreen wiper motor or mechanism is free of gripping from mechanical point of view.
Fix if necessary.
Perform again a system diagnostic
Repair the other possible failures
Erase the memorized failures.
AFTER REPAIRING
vnx.su