DACIA SOLENZA 2004 Repair Manual

86
86 - 1
AUTO RA DIO
The au to radio may be fitted in the versions: radio-tapes player and radio with CD player.
RADIO-TAPES P LAYER PRESENTATION
1. On/off key
2. Key for tape fast-forwards up to next song
3. Tape eject key
4. Tape inserting door
5. Keys for tape forwards/backwards
6. Multi-purpose key (audio source selection, sound adjustment, radio frequency selection, and
traffic information
7. Display
8. Keys for radio programs memorizing (key 1 is used also for DOLBY function in tape listenin g)
9. Multi-purpose key (after selecting one function, the adjustments in the areas +, - or > , < are
performed)
CD PLAYER PRESENTATION
1. On/off key
2. CD eject key
3. CD insert door
4. Multi-purpose key (audio source selection, sound adjustment, radio frequency selection, and
traffic information
5. Display
6. Key for radio programs memorizing (key 1 is also used for CD listening)
7. Multi-purpose key (after selecting one function, the adjustments in the areas +, - or > , < are
performed)
General
vnx.su

86
86 - 2
AUTO RA DIO
MAIN FUNCTIONS
Function “ON / OFF Logic”
The radio may operate also when engine is stopped, when contact key is on “S” position. In
this situation, after 20 minutes of operation, an acoustic signal will be heard and the radio will
automatically stop. If you wish that radio is not stopping, after you heard the acoustic signal, push
the red starting key (1) that is enabling the radio operation for another 20 minutes.
If the contact key is brought on position “M” or “A” and the radio is started by pushing the
key (1), after the contact is set off, the radio will automatically stop. At next setting of the contact
on the position “M” or “A”, the radio will automatically start on the program set before starting.
Adjustment of the acoustic volume
By pushing the keys + or -, the acoustic volume may be adjusted, reaching its increasing or
decreasing. The acoustic volume level will be displayed in the moment of its adjustment and may
be from 0 (minim) to 30 9maxim).
Sound correction
This function is enabling the boosting or decreasing of the high /low frequencies, as well as the
balancing of the right/left and rear/front acoustic level.
RAD I O
The radio device is of multiple frequencies range, c omplex and is allowing the programs
selection in frequency range long waves (UL), medium waves (UM or ultra-short (FM).
RDS system ( Radio data System)
This system is enabling mute data transmitting , in the same time with a FM radio station signal.
The radio may use this system that is bringing the following advantages:
- emitter name displaying;
- information regarding others radio emitters;
- emergency messages;
- automatic reactivation.
Radio frequency selecti on
In order to perform this, push the key “SRC” many times so that the desired radio frequency
is selected.
General
vnx.su

86
86 - 3
AUTO RA DIO
Radio tuning on a transmitter
The ra dio receiver is using three selection m odes that may be seen on the scre en and a p-
proached on the radio front side: -manually ( TUNER MANU )
- by pre-selection (TUNER PRESEL)
- in alphabetical order (LIST)
Program memorizing
Af ter the desired waves range has been selected (UL, UM or FM) and the transmitter
reception is established, its memorizing may be performed, by pushing on of the yes from 1 to 6,
for at least two seconds, when an acoustic signal confirming the memorizing is to be heard.
Thermal protection
If the radio tempera ture is too hi gh for an optimal opera tion, the volume i s automatically
reduced ( without modification of the volume on the display ).
Code protection
The radio i s protected by m eans of a four-digit c ode. This code i s introduced by the ra dio
keys at each battery disconnection.
Code introduction by means of the radio keys : in order to valid one digit introduction,
push the next key (see the Operation technical book). In case of a wrong code, t he ra dio i s getting bl ocked (one minute for the first e rror, two
minutes for the second error, four minutes for the third…)
Af ter first code introduction, some confi gurations must be programmed (see chapter”
configuration”). These are remaining programmed till battery disconnection.
REMARK: the return to the “wave jammer” mode is possible by simultaneously push-
ing of the keys 2 and 5 putting the radio under tension. Wait then for two minutes. Programming
OBSERVAT ION:
In order to select the operation area of the radio receiver, simultaneously push keys
2 and 5, putting so the radio under tension. Wait then for about two minutes. Introduce
the four digits code, then :
General
vnx.su

86
86 - 4
AUTO RA DIO
25
-select the adequate area
- America
- Japan
- Asia
-Ar abia
-O thers ( Europe, Africa, others)
- Select the sound tonality curves:
-0 : inactive adjustment
-1 : Twingo
-2 : Clio
-3 : Megane
-4 : Laguna
-5 : Top range
- speakers number configuration – with
or without rear speakers (RE AR OFF ).
REMARK : it is not necessary to perform the configuration after radio code intro-
duction further to a supply fai lure.
“ Expert “ operation mode.
In order t o pass in c onfiguration (Expert mode), perform a long pushing (4 seconds) on
“source” key until a beep is heard. This is allowing the following functions adjustment:
- AF mode activation ( automatic resetting)
-V olume modifi cation subject to the vehicle speed ( 5 for maximal modification, 0 for
modification canceling) -Loudness mode activation
- Assisted radio receiver mode activation
-N umber of speakers activation (2 or 4)
- Manual or dynamic list selection
REMARK: during c onfiguration one impulse on “source” ke y i s canceling t he
modifications.
Volume
The volume may be settled subject to vehicle speed. For the activation of this function, select
the desired volume modification curve, by means of the “ Expert “ mode (push longer on the
“ source” key, until a beep is heard): 5 for maximal modification, 0 for modification canceling.
REMARK : In order this function becomes operational check that radio is correctly
connected.
General
vnx.su

86
86 - 5
AUTO RA DIO
OBSERVATION : the auto radio is provided with a sound tonality modification subject to
vehicle type. To modify that, see chapter “ configuration”.
Self-diagnostic
This mode is allowing some main functions controlling:
-speakers testing
by simultaneously pushing of 2 and 4 keys, the speakers are supplied one by one. The display
is enabling their location. - reception level testing ( afte r fr equency displaying)
by simultaneously pushing of 1 and 6 keys, the display is showing the radio reception criteria:
- 9 or letter = good reception
- 3 = defective signal
- 2 = stereo sound loosing
Keys testing
The introduction of this mode is performed by simultaneously pushing of 3 and on/off keys.
Each key pushing may be seen on display. The exit from this checking mode is automatic, after
all keys have been pushed.
General
vnx.su

86
86 - 6
AUTO RA DIO
TAPES PLAYER
This function is completely automatic, immediately after the tape is being inserted in the device
through the door provided for this purpose, the tape being oriented with the opening towards right.
Ta p e f a s t forwards
For this purpose, the “sau” key must be pressed. During tape rewinding, the radio may be heard
and on the display the name of the radio station or its frequency will be displayed. The stopping of
the fast forwards is to be performed by pushing on the key next to the one initially pushed. If during
a tape listening, you wish the listening of the other side, push simultaneou sly the key “si”. This tapes
player is an auto-reverse type, so when finishing listening one side of a tape, automatically the sense
will change and the listening of the other side will continue.
The MSS system is to be activated by pushing key “MSS”, enabling the fast forwards of the tape
till the ne xt song, does not matter t he playing sense in use. Deactivation of this function is to be
performed by pushing again key <>.
Noise reduction – Dolby B function
If you a re using recorded tapes with noise re duction t ype Dolby B, push key <<1>> for a n
optimal sound playing, on the display, Dolby symbol will appear.
Ta pes player
vnx.su

86
86 - 7
AUTO RA DIO
CD P LAYER
CD (compact disc) playing.
Insert the CD, with the recorded face downward, in the door located on the device front part.
The CD lecture is beginning with track number 1.
If the CD has been previously inserted, then you switch on listening to a radio station, in case
you wish to listen again to the CD, push key SRC and select CD. The CD playing will continue
from its last stop.
After listening the last CD track, the playing is continuing beginning with track no.1.
Observations:
- The CD playing may be interrupted by the receipted information if radio has been previously
programmed to operate” Emergency messages reception”.
- If you after inserting the CD, you hear an acoustic signal (bip), check if the CD is not dirty
or damaged.
Track selection
In order t o select the de sired t rack, push consequently > or < till you reach the searched
track. The CD lecture will continue from the selected track.
Fast forwards/back wards
Push key > or < and maintain it pushed, performing in this way, the forwards and consequently
backwards of the track listen in that moment.
CD tracks random playing
In order to activate this function, push ke y ( 1). After finishing random playing of all CD
tracks, the lecture will c ontinue until its stop controlling. If key > is pushed, passing to the next
track, random selected, will be performed. If key < is pushed, playing again of the existent track
will be performed. In order to return to the normal track playing ( successive playing), key (1) i s
to be pushed and to be maintained for few seconds.
CD eject.
After CD playing, if CD ejection is desired, push key (2) EJECT, placed on the left side of
the device front panel.
OBSERVATIONS:
This CD player is reading only CD audio parts. If on CD there are also non-audio parts, they
can not be red and on the display the track number followed by the message NO AUDIO will be
displayed.
If a CD without a ny audio t rack, i s inserted in CD player, this one will be refused and the
message NO AUDIO will be displayed on the screen.
This CD player is operating only with 12-cm diameter CD.
CD Player
vnx.su

86
86 - 8
AUTO RA DIO
Black connector (A)
Pin DenominationWhite connector (C)
Pin Denomination
1+ Right rear speaker
2- Right re ar speaker
3+ Right front speaker
4– Right front speaker
5+ Left front speaker
6– Left front speaker
7+ Left re ar speaker
8– Left rear speaker
1Free
2Free
3Free
4Battery supply
5Free
6 Supply + parking
7 Supply + after contact
8 Mass
Conn ectors
OBSERVATION:
The speakers are c onnected in parallel on each e xit.
Conne ctor s
vnx.su

86
86 - 9
AUTO RA DIO
ROOF ANTENNA HOLDER
DISMOUNTING
Disconnect the battery (-) terminal.
Detach from clips the ceiling lamp using a straight head screwdriver (see chapter 80).
Disconnect the ceiling lamp connector
Dismount the attachment screw of the antenna holder on the roof.
Remove the antenna holder.
R EMOU NT I NG
Correctly position the antenna holder on the roof.
Mount the attachment nut of the antenna holder on the roof.
Connect the ceiling lamp connector
Attach in clips the ceiling lamp in its support.
Connect the battery (-) terminal.
Check the ceiling lamp and radio operation.
ROOF ANTENNA CABLE
DISMOUNTIN G
Dismount the upper part dashboard (see chapter 57).
Cut the attachment clip (1) of the roof antenna cable on the driving post cross member (mark
the clip mounting position).
Dismount the covering of the right front upper pillar and detach from clips the roof antenna
cable from covering.
Dismount the sun visors (see chapter 71).
Unstuck the two Aplix pills (2) from the roof.
Carefully remove the antenna cable (pull the end that was connected to the antenna holder).
Mark the mounting position of the antenna cable.
Roof antenna
vnx.su

86
86 - 10
AUTO RA DIO
REMOU NT I NG
Mount the antenna cable (insert the a ntenna c onnector ( 3) through the space be tween the
roof and the ceiling attachment support, observing the mounting position existent prior to the
dismounting. Mount the antenna holder on the roof.
Unstuck the Aplix pills protection and these are to stacked on the roof, attaching the antenna
cable. Mount the sun visors (see chapter 71).
Attach in clips the roof antenna cable on the covering of the right front upper pillar.
Mount the covering of the right front upper pillar.
Replace a nd mount the attachment clip of the roof antenna cable on the driving post cross
member, observing its mounting position existent prior to the dismounting.
M ount the upper dashboard (see chapter 57).
Roof antenna
vnx.su