battery DACIA SOLENZA 2004 Manual PDF

BATTERY - FRONT HEADLIGHTS
80
80 - 6
Bulbs
FOG PROJEC TOR B ULB RE PLACEMENT
DISMOUNTING
Suspend the vehicle on an elevator.
Disconnect the fog projector connector
Rotate the bulb holder ( F) an d extract it from its place.
REMOU NT I NG
Perform the dismounting operations in the reverse order, correctly positioning the bulb holder in
its place. Perform fog projector adjustment
NOTE :
Because the fog projector is equipped with a halogen bulb, do not touch the bulb glass
ba lloon directly by hand.
HEADLAMP BULB REPLACEMENT
DISMOUNTIN G
Disconnect the connector (2 ).
Remove the rubber protector ( 7). Mark its mounting position.
Release the atta chment clamp (8) and remove th e h e adlamp bulb
REMOU NT I NG
Perform the dismounting operations in the reverse order. Position correctly the rubber protector
( 7) observing the mounting position before dismounting. Perform headlamp adjustment.
NOTE :
Because the headlamp is equipped with a halogen bulb, do not touch the bulb glass balloon
d irectly by hand.
72 3 4
8
5
10
10
vnx.su

80
BATTERY - FRONT HEADLIGHTS
80 - 7
FRONT TURNING BULB REPLACEMENT
DISMOUNTIN
G
Disconnect the connector ( 3).
Rotate the holder ( 4) and remove it.
Remove the worn bulb from the holder
R EMOU NT I NG
Perform the dismounting operations in the reverse order, with t he checking of the correct
holder (4 ) positioning to avoid dust and humidity penetration in the headlamp assembly .
The turning lamps are using orange color bulb; when replacing the bulb, use the same bulb
type.
FRONT PARKING BULB REPLACEMENT
DISMOUNTIN G
Rotate the holder ( 5) and remove it.
Extract the worn bulb from the holder.
R EMOU NT I NG
Perform the dismounting operations in the reverse order, with t he checking of the correct
holder (5 ) positioning to avoid dust and humidity penetration in the headlamp assembly .
Bulbs
vnx.su

BATTERY - FRONT HEADLIGHTS
80
80 - 8
HEADLAMP-FRONT LAMP ASSEMBLY SEALING
(getting fogged, it has condensation water or water penetration)
The condensation water is not affecting the lighting quality.
No No
No
No
No Ye s
Ye s
Ye s Ye s
Bulbs
Check the front part of the assembly: direct
a water jet towards the headlamp glass.
Is the water penetrating inside the headlamp?
Is wa ter penetrating inside the parking-turning
lamp?
Visually check the headlamp rear part; rubber
protecto r of the headlamp bulb is correctly
mounted?
The he adlamp adju stment corrector is well
mounted?
The headla mp bulb is correctly mounted?
The aera tion holes are clogged?
The hea dl amp is steamed out or it has
condensa tion water inside?
Visually check the rear part of the parking-
turning lamp; t he parking bulb holder is
correc tly mounted?
Th e turning bulb holder is correctly mounted?
Replace the headlamp.
Replace the parking-turning lamp.
Mount corr ectly the rubber protector of the
h eadlamp bu lb. If this is not good, replace it.
Mount corr ectly the headlamp adjustment
co rrector and its rubber protector. If protector
is not good, replace it.
Mount correc tly the headlamp bulb.
If possible, eliminate the clogging cause. If
no t possible, replace the headlamp.
Explain th e client that this fact is a natural
one, no t a damage and there is no headlamp
corro sion risk. The condensation water will
disappear when the headlamp will be lighted;
the disappearing time of the condensation
wat er is subject to the environmental
humidity .
Mount co rrectly the parking bulb holder. If
its gasket is not good, replace it.
Mount co rrectly the turning bulb holder. If
its gasket is not good, replace it.
REMARK : If the client is i nsisting, proceed to headlamp drying:
- blow with dry air, if possible;
- naturally dry the headlamp by turning on the headlamps for couple of minutes
till condensation water elimination or headlamp defoggi ng. No
No
No
No Ye s
Ye s
Ye s
Ye s
vnx.su

80
BATTERY - FRONT HEADLIGHTS
80 - 9
MEETING LIGHTS ADJUSTMENT (LOW BEAM)This is performed by acting upon the V screw
(vertically plane adjustment) or H (horizontally
p lane adjustment). By screwing, the lighting beam
is ”lowering” and by unscrewing is “ascending”. Check if the l ighted area is centered on the
vertical axis and if the optical separation at 15°
coincide with the headlamp lighting. An error of
1 cm is admissible. A lighting beam displaced towards left has
the aspect shown in (p icture a) and a lighting
beam displaced towards right has the aspect
shown in (picture b )
ROAD LIGHTS ADJUSTMENT (LONG BEAM)
Check the position to c oincide with the
adjustment pe rformed for low beam and with
the lighting beam distributed between the two
vertical lines on the panel
When checking the long beam, the lighting
center of t he ellipse, must be l ocated on t he
cross marking the screen center. If a m ajor de viation c ompared with t he low be am i s noticed, i t is re commended t he bul b
replacement, this one being in most of the cases, responsible for such defect.
Headlamps adjustment
H
V
figura a figura b
vnx.su

BATTERY - FRONT HEADLIGHTS
80
80 - 10
FOG P ROJECTORS ADJUSTMENT
The fog projectors adjustment is to be performed in the following conditions:
- the vehicle to be placed on a horizontal surface;
- the vehicle has not passengers inside the cockpit or weights in the trunk;
- the tires a re pressurized a t the manufacturer prescribed pressure.
Further on, proceed as follows:
Bring the vehicle at the working place.
Position the adjustment device (headlamp adjustment device –E) in front of an optical center
of a fog lamp. Switch on the fog projectors. Rotate the adjustment screw of the fog lamp (D), by means of
a scre wdriver ( A), so that a n adjustment of 2 % i s obtained and t he separation between t he
lighted area and the dark one from the adjustment device is l ocated under the marked line (G)
This adjustment is to be performed in the same way as for the meeting lights adjustment.
Bring the adjustment device in front of the optical center of the second fog lamp;
Perform the fog projector adjustment;
Switch off the fog projectors.
H eadlamps adjustment
G
E
A
vnx.su

80
BATTERY - FRONT HEADLIGHTS
80 - 11
Disconnect the (-) plug of the battery;
Dismount
the headlamp adjusting control from the turning lamp-headlamp assembly:
- pull backward the gasket of the headlamp adjustment corrector ( 1);
- detach from clips the protector (2) of the headlamp adjustment mechanism;
- loosen the locking nut ( 3);
- detach from clips the he adlamp adjustment control cable ( 4) from the headlamp
adjustment corrector and then from the fork (5);
Dismount the headlamp adjusting control from the other turning lamp-headlamp assembly .
Detach from clips the headlamp adjustment control cables and cut the attachment collars.
Dismount the headlamps adjustment control button.
Dismount the attachment nut of the headlamp adjustment control on the dashboard.
Dismount the bonnet opening control cable from the opening handle (see chapter 52).
Detach from clips, by means of a straight screwdriver, the cables passing bushing from the
cowl panel.
Remove the headlamps adjusting control cables from the cowl-passin g hole. Mark the mounting
position of the headlamps adjustment control cables.
REMOU NT I NG
Insert the headlamps adjusting control cables through the cowl-passing hole, observing the
existent position prior to dismounting.
Insert the bonnet opening control cable through the cables passing bushing.
DISMOUNTIN G1
2
V
56 34
Replacement of the headlamps mechanic adjustment control
vnx.su

BATTERY - FRONT HEADLIGHTS
80
80 - 12
Replacement of the headlamps mechanic adjustment control
Attach on the cowl panel, by means of clips, the cables passing bushing, ensuring the cockpit
co mpartment sealing against possible water drain along the cables passing bushing.
Mount the bonnet opening control cable in the opening handle (see chapter 52). Position the
headlamp s adjustment control on the dashboard.
Mount the attachment nut of the headlamps adjustment control on the dashboard.
Mo unt the headlamps adjustment control button and turn it in the position “3”.
Mount the headlamp adjustment control to a turning lamp-headlamp assembly :
-a ttach in clips by means of a straight screwdriver, the headlamp adjustment control cable
in fork (5) a n d t h en in the headlamp adjustment corrector;
- tighten initially the cable by hand till the fork ( 5) is in contact with support ( 6) so that fork
is remaining at max. 0.5 mm again st the support;
-block the headlamp adjustment cable by means of the nut ( 3);
-a ttach in clips the protector ( 2) o f t h e headlamp adjustment mechanism;
- position correctly the gasket of the headlamp adjustment corrector – the vertical adjustment
screw ( V) mu st come out through the gasket.
Mount the headlamp adjustment control of the other turning lamp-headlamp assembly.
Attach in the attachment points, by means of clips, the headlamps adjusting control cables,
replace and mount the attachment collars, observing the mounting position prior to the dismounting.
Keep a distance of approximate 40 mm
± 10 mm between the right cable and the cylinder
no .1 spark plug cable, in order to avoid the loses due to electric-magnetic induction.
Reconnect the battery ( -) term inal.
Switch on the headlamps and check the operation of the headlamps mechanic adjusting control.
The adju stment of the luminous spot dip of the headlamps in the downward sense of the vehicle
loading condition is to be performed by bringing the headlamps adjusting button in the “ 0” position
an d then in the desired condition.
REMA RK : The r equired tighteni ng moment of the attachment nut of th e headlamps
adju stment control on the dashboard: 2 Nm.
vnx.su

81
INSIDE AND REAR LIGHTING
81 - 1
REAR LAMPS
RE AR LAMP REPLACEMENT
DISMOUNTIN G
Disconnect the battery (-) plug.
Disconnect the rear lamp connector .
Inside trunk, dismount the screw with triangle head ( A).
Extract the rear lamp towards outside.
R EMOU NT I NG
Perform the dismounting operations in the reverse order, positioning correctly the rear lamp in
its seat. Check the bulbs connections and operation.
Rear right lamp Rear left lamp
Rear right lamp connector Rear left lamp connector
Pin Denomination Pin Denomination
1+ Right stop lamp 1 Fog parking lamp supply
2+ Right parking lamp 2 Left turning lamp supply
3Free 3 Free
4 Mass 4 Mass
5 Right turning lamp supply 5 + Left stop lamp
6 Revere driving lamp supply 6 + Left parking lamp
Inside and rear lighting
A
6
1 B
B
B
B 6
1
vnx.su

INSIDE AND REAR LIGHTING
81
81 - 2
R
EPLACEMENT OF REAR TURNING,
P ARK ING, FOG, REVERSE DRIVING,
STOP BULB
DISMOUNTIN G
Disconnect the battery (-) terminal.
Disconnect the rear lamp connector
Dismount the screw with triangle head
Extract the rear lamp towards outside
Di smount the two attachment screws (B) of
the bulbs support on the lamp glass.
Dismount the worn bulb.
REMOU NT I NG
Perform the dismounting opera tions i n the
reverse order, checking the condition of the
s ealing ga sket between the lamp glass and the
bulbs support: if this one is not good, replace it.
Check the bulbs operation and connections.
REPLACEMENT OF LICENSE PLATE LAMP BULB
DISMOUNTIN G
Disconnect the battery (-) terminal.
Disconnect the license plate lamp connector.
Extract the license plate lamp holder.
Remove the worn bulb and replace it.
R EMOU NT I NG
Perform the dismounting opera tions i n the
reverse order. Check the bulb operation.
REPLACEMENT OF ADDITIONAL
STOP LAMP BULB
DISMOUNTIN G
Disconnect the battery (-) terminal.
Dismount the TORX 20 attachment screw
of the additional stop lamp. Mark the mounting
position of the lamp mass wire connector.
Inside and rear lighting
Disconnec t t he addit ional st op l amp
connector. Detach t he two side clips and extra ct the
reflector-glass assembly from the lamp body.
Detach carefully from clips the lamp glass,
by means of a straight screwdriver. Replace the worn bulb.
REMOU NT I NG
Perform the dismounting operations in the
reverse order. Check the bulb connections and
operation.
REPLACEMENT OF LICENSE PLATE LAMP
DISMOUNTIN G
Disconnect the battery (-) terminal.
Disco nnect the license plate lamp
connector. Detach from clips the license plate lamp.
REMOUNTING
Pe rform t he di smounting opera tions i n t he
reverse order. Check the bulb operation.
R EPLACEMENT OF ADDITIONAL
STOP LAMP
DISMOUNTIN G
Disconnect the battery (-) terminal.
Dismount the attachment screw TORX 20
of the additional stop lamp. Mark the mounting
position of the lamp mass wire connector.
Disconnec t t he addit ional st op l amp
connector.
R EMOU NT I NG
Perform the dismounting operations in the
reverse order. Check the bulb connections and operation.
vnx.su

INSIDE AND REAR LIGHTING
81
81 - 4
The ceiling lamp is central located, between
the two sun visors.
The ceiling lamp has 3 operating positions
subject to ceiling lamp glass position (4):
- position 1 : ceiling lamp off
- position 2 delayed ceiling lighting; this
will light for 15 seconds after driver’s front door
closing or after the command of unlocking the
doors with the RF remote control . This delay
turns out in the moment of setting the contact.
- position 3 : c eiling lamp pe rmanently
lighting.
DISMOUNTIN G
Disconnect the battery ( -) terminal.
Detach from clips the assemb ly from the lamp
support by means of a little screwdriver acting in
front of the slot (A). Disconnect the connector
Remove the roof lining around ceiling lamp
support. Detach from clips the ceiling lamp support.
REMOU NT I NG
Perform the dismounting operations in t he
reverse order. Check the ceiling lamp operation. Ceiling lamp connector
Pin Denomination
1 Mass
2+
protected battery – exit fuse F02
3 Ceiling lamp control
REPLACEMENT OF CEILING LAMP BULB
DISMOUNTIN G
Disconnect the battery (-) terminal;
Detach care fully the lamp glass using a
small screwdriver acting in point ( B).
Remove the worn bulb and replace it.
R EMOU NT I NG
Perform the dismounting operations in the
reverse orde r, using for lamp glass clips
attachment, a small screwdriver positioned in
point (B).
Check the ceiling lamp operation.
Ceiling lamp
A
B
3 1
vnx.su