ECU DODGE RAM SRT-10 2006 Service Repair Manual

3. Remove the cap (1) and the bolt (2) that secures
the seat belt (3) to the top of the B-pillar (4) and
position the seat belt out of the way.
4. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs that secure the upper B-pillar trim
panel (5) to the B-pillar and remove the trim panel.
INSTALLATION
REGULAR CAB
1. Position the upper B-pillar trim panel (5) to the
B-pillar (4).
2. Engage the retaining tabs that secure the upper
B-pillar trim panel to the B-pillar.
3. Install the bolt (2) that secures the seat belt (3) to
the top of the B-pillar. Tighten the bolt to 40 Nꞏm
(30 ft. lbs.).
4. Install the cap (1) onto the seat belt.

QUAD CAB
1. Position the upper B-pillar trim panel (5) to the
B-pillar (4).
2. Engage the retaining tabs that secure the upper
B-pillar trim panel to the B-pillar.
3. Install the bolt (2) that secures the seat belt (3) to
the top of the B-pillar. Tighten the bolt to 40 Nꞏm
(30 ft. lbs.).
4. Install the cap (1) onto the seat belt.
5. Install the grab handle (1) onto the B-pillar and
install the two bolts (3). Tighten the bolts to 6 Nꞏm
(55 in. lbs.).
6. Close the two fastener covers (2) located on the
grab handle.

C-PILLAR LOWER TRIM
REMOVAL
1. Remove the upper C-pillar trim panel (Refer to 23 -
BODY/INTERIOR/C-PILLAR TRIM - REMOVAL).
2. Remove the bolt (3) that secures the seat belt (2)
to the bottom of the C-pillar (4) and position the
seat belt out of the way.
3. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs that secure the lower C-pillar trim
panel (1) to the C-pillar.
4. Remove the seat belt from the lower C-pillar trim
panel through the slot provided and remove the
trim panel.
INSTALLATION
1. Route the seat belt (2) through the slot in the lower
C-pillar trim panel (1) and position the trim panel to
the C-pillar (4).
2. Engage the retaining tabs that secure the lower
C-pillar trim panel to the C-pillar.
3. Install the bolt (3) that secures the seat belt to the
bottom of the C-pillar. Tighten the bolt to 40 Nꞏm
(30 ft. lbs.).
4. Install the upper C-pillar trim panel (Refer to 23 -
BODY/INTERIOR/C-PILLAR UPPER TRIM -
INSTALLATION).

C-PILLAR UPPER TRIM
REMOVAL
1. Remove the cap (1) and then the bolt (2) that
secures the seat belt (3) to the top of the C-pillar
(4) and position the seat belt out of the way.
2. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs that secure the upper C-pillar
trim panel (5) to the C-pillar and remove the trim
panel.
INSTALLATION
1. Position the upper C-pillar trim panel (5) to the
C-pillar (4).
2. Engage the retaining tabs that secure the upper
C-pillar trim panel to the C-pillar.
3. Install the bolt (2) that secures the seat belt (3) to
the top of the C-pillar. Tighten the bolt to 40 Nꞏm
(30 ft. lbs.).
4. Install the cap (1) onto the seat belt.

CARPETS AND FLOOR MATS
REMOVAL
NOTE: Carpet for Quad Cab model shown. Regular cab similar.
1. Remove the front seats (Refer to 23 - BODY/
SEATS/SEAT - FRONT - REMOVAL).
2. If equipped, remove the floor console (Refer to 23 -
BODY/INTERIOR/FLOOR CONSOLE -
REMOVAL).
3. If equipped, remove the three bolts (1) that secure
the rear storage compartment (2) to the floor panel
(3) and remove the storage compartment from the
rear trim panel (4).
4. On Quad Cab models, remove the rear seats (1)
(Refer to 23 - BODY/SEATS/SEAT - REAR -
REMOVAL).
5. On Quad Cab models, remove the rear cup holder
(2) using a trim stick C-4755 or equivalent.

6. Remove the lower B-pillar trim panels (Refer to 23
- BODY/INTERIOR/B-PILLAR LOWER TRIM -
REMOVAL).
7. On Quad Cab models, remove the bolt that
secures the lower seat belt anchor to the floor
panel near the B-pillars (Refer to 8 - ELECTRICAL/
RESTRAINTS/SEAT BELT & RETRACTOR -
REMOVAL).
8. Remove the retaining screw (1) that secures the
jack assembly (2) to the floor panel (3) and remove
the jack assembly.
9. Remove the two bolts (4) that secure the jack
assembly to the floor panel.
10. For trucks equipped with a scissor type jack,
remove the bolts (1) and remove the jack (2).
11. Remove the screws and remove the load floor
storage strap snaps (1).

12. On Quad Cab models, remove the eleven push-
pin fasteners (1) that secure the rear of the carpet
(2) to the floor panel (3).
13. Remove the carpet from the vehicle.
INSTALLATION
NOTE: Carpet for Quad Cab model shown. Regular cab similar.
1. Position the carpet (2) into the vehicle.
2. On Quad Cab models, install the eleven push-pin
fasteners (1) that secure the carpet to the floor
panel (3).
3. Install the load floor storage snaps and screws (1).

4. On trucks equipped with a scissor jack, install the
jack and install the bolts (1).
5. Install the two bolts (4) that secure the jack assem-
bly (2) to the floor panel (3).
6. Position the jack assembly onto the two bolts and
install the retaining screw (1). Tighten the screw
securely.
7. On Quad Cab models, install the bolt that secures
the lower seat belt anchors the floor panel near the
B-pillars (Refer to 8 - ELECTRICAL/RESTRAINTS/
SEAT BELT & RETRACTOR - INSTALLATION).
Tightentheboltto40Nꞏm(30ft.lbs.).
8. Install the lower B-pillar trim panels (Refer to 23 -
BODY/INTERIOR/B-PILLAR LOWER TRIM -
INSTALLATION).
9. On Quad Cab models, install the rear seat (1)
(Refer to 23 - BODY/SEATS/SEAT - INSTALLA-
TION).
10. On Quad Cab models, install the rear cup holder
(2).

COWL TRIM
REMOVAL
1. Using a trim stick C-4755 or equivalent, disengage
the retaining tabs of the cowl trim panel (1) from
the retainer clips (2) in the door sill (3).
2. Pull the cowl trim panel rearward and remove it
from the vehicle.
INSTALLATION
1. Position the cowl trim panel (1) onto the door sill
(3).
2. Push the cowl trim panel forward and then engage
the retaining tabs that secure the sill trim panel to
the rear door sill.

FLOOR CONSOLE
REMOVAL
Mini Floor Console
1. If equipped, remove the 4WD gear shift boot (Refer
to 23 - BODY/INTERIOR/4WD FLOOR SHIFT
BOOT - REMOVAL).
2. If equipped with a manual transmission, remove
the transmission gear shift lever extension.
3. Remove the console inserts, if equipped.
4. Remove the bolts (2) that secure the rear console
(1) to the floor panel.
5. Lift up the rear of the floor console to clear the
gear shift lever, if equipped.