Time FIAT 500 2018 Owner handbook (in English)

KNOWING YOUR CAR
26
DEACTIVATING FRONT
PASSENGER AIRBAG
AND SIDE BAG
(for versions/markets, where provided)
This function allows the passenger side
airbag to be activated/deactivated.
Proceed as follows:
❒ briefly press MENU
Nbutton and,
after displaying the message
(Passenger bag: Off)
(to deactivate) or the message
(Passenger Bag: On) (to activate) by
pressing the + and – buttons, press
the MENU
Nbutton again;
❒ the confirmation request message is
displayed;
❒ press buttons + or – to select (Yes)
(to confirm activation/deactivation)
or (No) (to abort);
❒ briefly press MENU
Nto confirm
setting and go back to the menu
screen or hold the button down to
go back to the standard screen
without saving.With Passenger’s protection not
active, the LED “on the instrument
panel lights up fixed.
SERVICE
(SCHEDULED
SERVICING)
This function allows you to display the
information about km/mileage intervals
or, for versions/markets, where
provided, time intervals for car
servicing.
To consult the information, proceed as
follows:
– briefly press the MENU
Nbutton:
the display shows when servicing is
due in kilometres/miles or days (where
provided) according to the previous
setting (see paragraph “Units of
measurement”);
– briefly press the MENU
Nbutton to
go back to the menu screen or press
the button for long to go back to the
standard screen.
IMPORTANT The “Scheduled Servicing
Plan” includes car maintenance at fixed
intervals (refer to the “Maintenance and
care” chapter).This is displayed automatically, with
ignition key at MAR-ON, 2000 km (or
equivalent value in miles) before
servicing or, where provided, 30 days
before servicing. It is also displayed
each time the key is turned to MAR-
ON or, for versions/markets, where
provided, every 200 km (or equivalent
value in miles). Below this threshold
servicing indications are more frequent.
The display will be in km or miles
according to the unit of measurement
set. When the following scheduled
servicing is approaching, the word
“Service” will appear on the display,
followed by the number of
kilometres/miles or days (where
provided) left, when the key is turned to
MAR. Go to a Fiat Dealership, where the
“Scheduled Servicing Plan” operations
will be performed and the message will
be reset.
When the service interval is reached
and for about 1000 km/600 mi or 30
days, a service due message is
displayed.

27
HEADLIGHT
ALIGNMENT
With the ignition key at MAR and
dipped beam headlights on, press the
+ button to adjust the headlights
upwards and the – button to adjust the
headlights downwards.
TYRE RESET (ITPMS
RESET)
(for versions/markets, where provided)
With this function it is possible to reset
the iTPMS (see paragraph “iTPMS”). To
carry out the Reset procedure proceed
as follows:
❒ briefly press the MENU
N; the
display will show “Reset”;
❒ press button + or – to select (“Yes”
or “No”); a dedicated reset
confirmation message will appear;
❒ briefly press the MENU
N; the
display will show “Confirm”;
THE KEYS1)
1) 1)
CODE CARD
(for versions/markets, where provided)
The car is delivered with two copies of
the ignition key and with the CODE
card fig. 7 which bears the following:
A: the electronic code;
B: the mechanical key code to be given
to the Fiat Dealership when ordering
duplicate keys.
You should have the electronic code
with you at all times.
IMPORTANT All the keys and the
CODE card must be handed over to
the new owner when selling the car.
MECHANICAL KEY
The metal insert A-fig. 8 operates:
❒ the ignition switch;
❒ the door locks and the tailgate (for
versions/markets, where provided);
❒ the locking/unlocking of the fuel
cap.
KEY WITH REMOTE
CONTROL
(for versions/markets, where provided)
The metal insert A-fig. 9 operates:
❒ the ignition switch;
❒ the door locks;
❒ the locking/unlocking of the fuel
cap.
7DVDF0S0103c
8DVDF0S0104c

KNOWING YOUR CAR
28
FIAT CODE
SYSTEM
The Fiat Code system is an electrical
engine immobiliser system which
increases protection against attempted
car theft. It is automatically activated
when the ignition key is removed.
Each time the vehicle is started by
turning the ignition key to MAR, the Fiat
CODE system control unit sends a
recognition code to the engine control
module to deactivate the immobiliser.
If, during ignition, the code is not
correctly recognized, a warning light
is lit on the instrument panel .
In this case, turn the key to STOP and
then to MAR-ON; if it is still locked, try
again with the other keys that come
with the car.
Contact a Fiat Dealership if you still
cannot start the engine.
NOTE Each key has its own code
which must be stored by the control
unit of the system.
Contact a Fiat Dealership to have new
keys (up to 8) stored with a code.
IGNITION
DEVICE
The key can be turned to three
different positions fig. 10:
❒ STOP: engine stopped, key can be
removed, steering column locked.
Some electrical devices (e.g. audio
system, central door locking
system, etc.) can operate;
❒ MAR: driving position.
All electrical devices are enabled;
❒ AVV: engine starting.
The ignition device is fitted with a
safety system that requires the ignition
key to be turned back to STOP if the
engine does not start, before the
starting operation can be repeated.
10DVDF0S011c
Pressing button B opens/closes the
metal insert.
Briefly press button
Ë: for unlocking of
doors and tailgate, timed switching-on
of interior lights and double flashing of
direction indicators (for
versions/markets, where provided).
Briefly press button
Á: for remote
locking of doors and tailgate,
switching-off of the internal ceiling
lights and single flashing of direction
indicators (for versions/markets, where
provided).
Press the Rbutton: remote opening
of the luggage compartment and
double flashing of the direction
indicators.
9DVDF0S0105c

KNOWING YOUR CAR
32
INTERIOR
ELECTROCHROMIC
REAR-VIEW MIRROR
(for versions/markets, where provided)
Some versions have an electrochromic
mirror with automatic antiglare
function.
There is an ON/OFF button on the
lower part of the mirror for
activating/deactivating the
electrochromic function. When the
function is active, a LED on the mirror
is active. When reverse is engaged, the
mirror is automatically set for daytime
use.Folding the mirrors
When required (for example when the
mirror causes difficulty in narrow
spaces) it is possible to fold the mirror
by moving it from position 1 fig. 21
(open), to position 2 (closed).
DOOR MIRRORS
With manual adjustment
The door mirror can be adjusted from
outside by exerting a slight pressure
on the four sides of the glass.
With electrical adjustment
Proceed as follows:
❒ select the mirror using
selector B Fig. 20 ;
❒ adjust the mirror using the joystick A
in the four directions.
20DVDF0S0107c
21DVDF0S0108c

35
With the selector switch in the AUTO
position, the side lights and dipped beam
headlights are controlled by the dusk
sensor.
MAIN BEAM
HEADLIGHTS
❒ With the ring in the 2position,
push the stalk forwards towards the
dashboard. The
1warning light on
the instrument panel will light.
❒ For vehicles with the AUTO
function: with the ring in the AUTO
position and the dipped beam
headlights on, push the stalk
forwards toward the dashboard.
❒ They are deactivated by pulling the
stalk towards the steering wheel.
Flashing
❒ You can flash the beams pulling the
stalk toward the steering wheel
(unstable position).
PARKING LIGHTS
These lights can be turned on with the
starter switch in the STOP position or
with the key removed, by moving the
left stalk ring first to the position (or
the AUTO position if the vehicle does
not have a dusk sensor) and then to
position
2.The warning light
3lights on the
instrument panel. Repeat the same
operation to switch them off.
DIRECTION INDICATORS
Bring the stalk to the (stable) position:
❒ up a: activates the right direction
indicator;
❒ down b: activates the left direction
indicator.
LANE CHANGE
FUNCTION
❒ Move the lever upwards or
downwards (unstable position) for
less than half a second and the
direction indicator will flash 3 times
to signal a lane change, then
immediately switch off
automatically.
FOLLOW ME HOME
This function allows the space
surrounding the car to be lit up for the
set period of time.
Activation
The “Follow Me Home” device is
activated by pulling the stalk fig. 25
towards the steering wheel, in addition
to the stroke end click.
EXTERNAL LIGHTS
DAYTIME RUNNING
LIGHTS
7)
❒ For vehicles with the AUTO
function: with the key in the MAR
position and the ring turned to the
O position, the daytime running
lights switch on automatically.
❒
For vehicles with the AUTO function:
the daytime running lights are turned
on automatically by the dusk sensor
when the ring is in the AUTO position.
DIPPED HEADLIGHTS/
SIDE LIGHTS
❒ With key at MAR, turn the ring nut to
2. The warning light
3on the
instrument panel will come on. When
the dipped beam headlights are on,
the daytime running lights switch off.
24
1
2
DVDF0S008c

KNOWING YOUR CAR
36
It is possible to enable this function
within 2 minutes after turning off the
engine. This function allows turning on
lights and low beams. It is possible to
set the headlights turning on time by
pulling the left lever towards the
steering wheel (unstable position) one
or more times. In this case it is
possible to choose between 0, 30, 60,
90 up to a maximum of 210 seconds.
Each time the stalk is operated, the
warning light
3on the instrument
panel switches on. The display shows
a message and the time set for the
function.
The
3warning light comes on when
the stalk is first moved and stays on
until the function is automatically
deactivated.
Deactivation
This function is deactivated turning on
again the headlights, sidelights or
pulling the left lever towards the
steering wheel (unstable position) for
more than 2 seconds, or switching the
starter to MAR.
AUTO FUNCTION
(Dusk sensor)
(for versions/markets, where provided)
This is an infrared LED sensor that works
in conjunction with the rain sensor. It is
located on the windscreen (fig. 25) and is
able to detect variations in outside
lighting based on the light sensitivity set
in the display Menu or the Uconnect™
5" or 7" HD system (where provided).
The higher the sensitivity, the lower the
amount of external light needed to
automatically switch the external lights
on.
25DVDF0S0215c
Function activation
Turn the left stalk ring A fig. 26 to the
AUTOposition.
IMPORTANT The function can only be
activated with the ignition device in the
MAR position.
Function deactivation
To deactivate the function, turn the left
stalk ring A to position 2.
26DVDF0S0216c

KNOWING YOUR CAR
40
Emergency manoeuvre
If the control buttons fail to operate, the
sunroof can be moved manually,
proceeding as described below:
❒ remove the protective cap A-fig. 33
located on the internal covering,
behind the blinds;
❒ take the Allen key (provided as
standard) from the toolbox in the
boot;
❒ fit the Allen key in position B and
turn it:
– clockwise, to open the roof;
– anticlockwise, to close the roof.
33DVDF0S019c
SOFT TOP 10), 11) 6)
❒ The soft top can be opened/closed
through buttons A or B-fig. 34,
located near the ceiling light.
it is advisable to close the soft top
when the car is parked.
The closed top effectively protects the
car from rain and from theft.
IMPORTANT: the motor may overheat
if the soft top is repeatedly operated
within a short space of time, thus
causing the overheating protection to
inhibit system operation. Wait for a
minute and repeat.
Opening from initial position: all
closed soft top
❒ Pressing the one-touch button
A-fig. 34 once the soft top opens
automatically to the horizontal
opening position (spoiler position -
see fig. 35).
❒ If one of the two buttons is pressed
before reaching the stop position,
the top may stop in an intermediate
horizontal opening position.
35DVDF0S174c
34DVDF0S020c

43
❒ The activation of the heated rear
windscreen, upon request by the
user, is carried out only if the soft
top is completely closed. If the soft
top is closed incorrectly, the heated
rear window does not operate and
the relevant warning light does not
come on.
❒ When the soft top is opened using
the relevant control, if the heated
rear windscreen had been engaged
it is automatically deactivated and
the warning light switches off.
❒ Do not remove ice from the soft top
with sharp items.
❒ Do not use scrapers or sprays to
remove ice from the heated rear
window to prevent damage.
❒ Do not put objects on the top: they
could fall if the top is operated
causing damage and injury.
❒ It is advisable to cover the top with
a protective sheet if the car is left
parked in the open for a long time.❒ Do not keep the soft top folded for
a long time: this could cause folds
and creases in the fabric.
❒ Before moving the soft top, check
that there is enough room to carry
out the operation and that there are
no obstacles or people close to the
moving parts of the soft top.
❒ The cooled air flow into the
passenger compartment may
decrease if the automatic climate
control system is on and the top is
not all closed.
❒ With the top open and the car
travelling, the speech recognition
system may be recognised voice
controls because of the background
noise: then the top is closed the dial
number command may not be
recognised.DOORS
12) 9)
To open manually from outside
(driver side door)
From outside, insert the key, turn it in
direction 1 fig. 38 and pull the handle. If
the car has central locking, turning the
key opens all the locks.
38DVD F0S0109c

KNOWING YOUR CAR
48
Emergency braking
In the event of emergency braking the
hazard warning lights switch on
automatically as well as warning lights
andin the instrument panel.
The lights switch off automatically
when emergency braking ceases.
FRONT/REAR FOG
LIGHTS
(for versions/markets, where provided)
With the dipped beam headlights on,
to turn on the front/rear fog lights, use
the button A fig. 49 as follows:
❒ press once: fog lights on, warning
light
5appears on the instrument
panel;
48DVDF0S0180c
❒ press twice: rear fog lights on,
warning light
4appears on the
instrument panel;
❒ press three times: front/rear fog
lights off.
REAR FOG LIGHTS
(for versions/markets, where provided)
With the dipped beam headlights on,
turn on the rear fog lights pressing the
button B fig. 49. The
4warning light
on the instrument panel will come on.
Press the button again to switch the
lights off.
49DVDF0S0181c
ABS SYSTEM 15)
This system, which is an integral part
of the braking system, prevents one or
more wheels from locking and slipping
in any road surface condition,
irrespective of the intensity of the
braking action, ensuring that the car
can be controlled even during
emergency braking thus optimising
stopping distances.
SYSTEM INTERVENTION
The driver can feel that the ABS
system has come into action because
the brake pedal pulsates slightly and
the system gets noisier: this is entirely
normal with the system operating.

KNOWING YOUR CAR
50
iTPMS System
(indirect Tyre
Pressure
Monitoring System)
(for versions/markets, where provided)
48)
RESET PROCEDURE
The iTPMS needs an initial “self-
learning” phase (with length depending
on the driving style and road
conditions: optimal conditions being
driving on a straight road at 80 km/h
for at least 20 minutes) which starts
when the Reset procedure is carried
out.
The Reset procedure must be carried
out:
❒ each time tyre pressure is
modified;
❒ when even only one tyre is
changed;
❒ when tyres are rotated/inverted;
❒ when the space-saver wheel is
fitted.
In a few situations such as sporty
driving, particular conditions of the
road surface (e.g. icy, snowy,
unsurfaced roads...) the signalling may
be delayed or partial in detecting the
contemporary deflation of more than
one tyre.
Under special conditions (e.g. vehicle
loaded asymmetrically on one side,
towing a trailer, damaged or worn tyre,
fitting the space-saver wheel, use of
the “Fix&Go” quick tyre repair kit,
fitting snow chains, fitting different
tyres on the axles) the system may
give false indications or be temporarily
deactivated.
If the system is temporarily
deactivated, the warning light
nflashes for about 75 seconds and then
is continuously on; at the same time,
the display shows a dedicated
message.
This indication is displayed also after
the engine has been switched off and
then on again if the correct operating
conditions are not restored. Before carrying out the “Reset”
procedure, inflate the tyres to the
rated pressure values specified in the
inflation pressure table (see “Wheels”
paragraph in the “Technical
specifications” chapter).
If the Reset procedure is not carried
out, in all above cases, the
nwarning light may give false indications
on one or more tyres.
To carry out the Reset procedure, with
the vehicle stopped and the ignition
key at MAR, use the setup menu (see
the description of the “Display”
paragraph). At the end of the Reset
procedure the display will show the
“Reset saved” message, indicating
that the self-learning has been started.
If the iTPMS self-learning is not
correctly executed, the message is not
displayed.
OPERATING
CONDITIONS
The system is active for speeds above
15 km/h.