Fuel line FORD FIESTA 2007 Owner's Guide

Fuel Charging and Controls - 2.OL
303-04B-5 Duratec-HE (M14) 303-04B-5
DIAGNOSIS AND TESTING
Fuel Charging and Controls
General Equipment
Wgnostic System (WDS) I
Principles of Operation
Ethanol equipped vehicles
Ethanol, is derived from cellulose waste. A large
proportion of Ethanol is distilled from corn, wheat
and sugar cane crops. The product that is to be
used in this vehicle is called Ethanol E85. E85 is
a mixture of 15% gasoline and 85% Ethanol.
Ethanol is a clear liquid and when fully burnt the
combustion gasses remaining are Carbon Dioxide
and water. This makes the use of Ethanol a good
environmental proposition. One drawback with pure
Ethanol is that it is corrosive to certain rubber and
plastic materials. The
introduction of Ethanol E85 has required some
major internal changes to the fuel supply and
delivery system. Some earlier vehicles used an
Ethanol mixture called Ethanol
El 5. This fuel was
made up of 15% Ethanol and 85% gasoline. At this
mixture ratio, no changes to the fuel charging or
delivery system where required, as no degradation
would occur with the cylinder head valves or
material content of the components, although some
performance loss would be noticeable.
The components used by vehicles running Ethanol
appear to be the same in construction as those
that use unleaded fuel only. The changes are
mainly to do with the materials used and increases
in fuel flow rates.
Ethanol has a much higher octane rating than
standard fuel which means that the ignition and
fuel injection calibrations for a vehicle that is
capable of using Ethanol E85 must be adapted
suitably.
I Item Description
I 1 I Fuel injectors
1ue1 rail I
2006.0 Fiesta 1212006 GI 65371 en
Item Description
3
4
Block heater
Fuel pump module
procarmanuals.com

Fuel Charging and Controls - 2.OL
303-04B-8 Duratec-HE (M14) 303-04B-8
DIAGNOSIS AND TESTING
lntake manifold
item Description
I 1 I Intake manifold tuning (IMT) swirl plates I Inspection and Verification
121
lntake manifold runner control (IMRC)
throttle plates
The intake manifold for both Ethanol
E85 and
standard unleaded fueled vehicles is the same
construction.
Built into the intake manifold, are the
IMRC throttle
plates and IMT swirl plates.
Under low demand throttle conditions, the air
charge is delivered to the cylinder head intake ports
through the primary air intake chambers. The clean
flow of the air charge is disturbed by the IMT swirl
plates to assist in the mixing of the air fuel mixture
at the fuel injectors.
1. Verify the customer concern.
2. Visually inspect for obvious signs of mechanical
or electrical damage.
Visual lnspection Chart
I Mechanical I Electrical I
- Fuel leak(s)
- Vacuum line(s)
- Gasket(s)
- Seal(s)
- Fuel injector(s)
- Throttle body
- Fuel rail
- Powertrain control
module (PCM)
- Wiring harness
- Electrical
connector(s)
- Throttle body
- Fuel injector(s)
2006.0 Fiesta 1212006 GI 65371en
During high demand throttle conditions, the IMRC
throttle plates are opened and the air charge is - Fuel supply line
allowed to use both primary and secondary intake
chambers. This means a higher volume of air 3. If an obvious cause for an observed or reported
charge can be accommodated by the intake concern
is found, correct the cause (if
possible) (
before proceeding to the next step. \. . manifold. During this high demand throttle
condition, the IMT swirl plates are fully open so as
4. If the cause is not visually evident, verify the
not to restrict the air charge flow.
symptom and refer to the Symptom Chart.
procarmanuals.com

Fuel Charging and Controls - 2.OL
303-04B-9 Duratec-HE (M14) 303-04B-9
DIAGNOSIS AND TESTING
Symptom Chart
Symptom Chart
Symptom
Possible Sources Action
Engine does not crank
Engine cranks but does not
start PATS. CHECK
the PATS LED extin-
guishes within 3 seconds when
the ignition is turned on.
REFER to: Anti-Theft
- Passive
(41 9-01
8, Diagnosis and
Testing).
Starting system.
REFER to: Starting System
(303-06, Diagnosis and
Testing).
Ignition switch. REFER to the Wiring
Diagrams.
Powertrain control module
(PCM).
Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
Low fuel system pressure.
Inertia fuel shutoff (IFS) switch.
Check the fuel system pres-
sure.
REFER to: Fuel System Pres-
sure Check (31
0-OOA,
General Procedures).
RESET the IFS switch.
Fuel lines damaged or blocked.
INSPECT the fuel lines.
INSTALL new components as
necessary. TEST the system
for normal operation.
I Fuel filter blocked. I INSTALL a new fuel filter. I
Fuel pump module. REFER to: Fuel System - 1.3L
Duratec-8V (Rocam)/l.25L
Duratec-1 6V (Sigma)/2.OL
Duratec-HE (M14)/1.4L
Duratec-1 6V (Sigma)/l .6L
Duratec-1
6V (Sigma) (31 0-00
Fuel System
- General
Information, Diagnosis and
Testing).
Crankshaft position (CKP)
sensor. Carry out a
full engine
diagnosis using the guided
diagnostic menu in WDS.
Camshaft position (CMP)
sensor. Carry out a
full engine
diagnosis using the guided
diagnostic menu in WDS.
PCM. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
2006.0 Fiesta 1212006 GI 65371 en
procarmanuals.com

Fuel Charging and Controls - 2.OL
303-048-1 2 Duratec-HE (M14) 303-04B-12
DIAGNOSIS AND TESTING
Symptom Possible Sources Action
Incorrect or contaminated fuel. CHECK for signs of
tion such as strange odors from
the fuel tank.
If contaminated fuel is found,
DRAIN the complete fuel
system. FLUSH the fuel system
through with clean gasoline.
REFER to: Fuel Tank Draining
(31
0-OOA, General Proced-
u res)
.
INSTALL a new fuel filter.
INSPECT the fuel injectors.
CLEAN the fuel injectors or
INSTALL a new set of injectors
as required only after the
checks have been carried out.
INSTALL a new fuel rail.
REFER to: Fuel Injection
Supply Manifold
(303-04C,
Removal and Installation).
Low fuel system pressure. Check the fuel system pres-
sure.
RE.FER to: Fuel System Pres-
sure Check (31
0-OOA,
General Procedures).
I Fuel filter blocked. I INSTALL a new fuel filter. I
EGR valve sticking open. REFER to: Engine Emission
Control (303-08 Engine
Emission Control
- 2.OL
Duratec-HE (M14), Diagnosis
and Testing).
INSPECT the fuel injectors.
CLEAN the fuel injectors or
INSTALL a new set of injectors
as required only after the
checks have been carried out.
CKP sensor. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
Knock sensor (KS). Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
Fuel injection supply manifold
fuel pressure sensor. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
2006.0 Fiesta 1212006 GI 65371 en
procarmanuals.com

Fuel Charging and Controls - 2.OL
303-04B-13 Duratec-HE (M14) 303-04B-13
DIAGNOSIS AND TESTING
Possible Sources Action
,
Engine ignition.
Symptom
Engine stumbling
Engine lacks power
REFER to: Engine lgnition
(303-07B, Diagnosis and
Testing).
Fuel injectors.
INSPECT the fuel injectors.
CLEAN the fuel injectors or
INSTALL a new set of injectors
as required only after the
checks have been carried out.
Low fuel system pressure.
EGR valve sticking open.
Check the fuel system pres-
sure.
REFER to: Fuel System Pres-
sure Check (31
0-OOA,
General Procedures).
Fuel rail fuel pressure sensor.
REFER to: Engine Emission
Control (303-08 Engine
Emission Control
- 2.OL
Duratec-HE (M14), Diagnosis
and Testing).
Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
Engine ignition. REFER to: Engine lgnition
(303-07B, Diagnosis and
Testing).
Brakes binding.
I CHECK the braking system.
REFER to: Brake System (206-
1 00, Diagnosis and Testing).
Vehicle overloaded, or
excessive wind resistance (roof
racks, towing etc). ADVISE
the customer about
the effects of overloading the
vehicle and wind resistance on
the fuel consumption.
Air cleaner element blocked.
REFER to: Fuel System Pres-
sure Check (31
0-OOA,
General Procedures).
INSTALL a new air cleaner
element as necessary.
Low fuel system pressure.
r
Check the fuel system pres-
sure.
2006.0 Fiesta 1212006 GI 65371 en
Kinked or restricted fuel lines. INSPECT the fuel lines.
INSTALL new components as
necessary. TEST the system
for normal operation.
procarmanuals.com

Fuel Charging and Controls - 2.OL
303-048-1 4 Duratec-HE (M14) 303-04B-14
DIAGNOSIS AND TESTING
Symptom Possible Sources Action
lncorrect or contaminated fuel. CHECK for signs of
tion such as strange
the fuel tank.
If contaminated fuel is found,
DRAIN the complete fuel
system. FLUSH the
through with clean gasoline.
REFER to: Fuel Tank Draining
(31
0-OOA, General Proced-
ures).
INSTALL a new fuel filter.
INSPECT the fuel injectors.
CLEAN the fuel injectors or
INSTALL a new set of injectors
as required only after the
checks have been carried out.
INSTALL a new rail.
REFER to: Fuel Injection
Supply Manifold
(303-04C,
Removal and Installation).
I Fuel filter blocked. I INSTALL a new fuel filter. I
REFER to: Engine Emission
Control (303-08 Engine
Emission Control
- 2.OL
Duratec-HE (M14), Diagnosis
and Testing).
I
Vehicle speed sensor (VSS). Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
ECT sensor. Carry out a full engine
diagnosis using the guided diagnostic menu in WDS.
Fuel injectors. INSPECT the fuel injectors.
CLEAN the fuel injectors or
INSTALL a new set of injectors
as required only after the
checks have been carried out.
Fuel rail fuel pressure sensor. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
I Incorrect valve timing. I CHECK the valve timing. I
Low cylinder compression.
--
CHECK the cylinder compres-
sion.
2006.0 Fiesta 1212006 GI 65371 en
procarmanuals.com

Fuel Charging and Controls - 2.OL
303-04B-16 Duratec-HE (M14) 303-04B-16
DIAGNOSIS AND TESTING
Symptom Possible Sources Action
Incorrect or contaminated fuel. CHECK for signs of contamina-).-
tion such as strange odors from, .,,
,
the fuel tank.
If contaminated fuel is found,
DRAIN the complete fuel
system. FLUSH the fuel system
through with clean gasoline.
REFER to: Fuel Tank Draining
(31
0-OOA, General Proced-
ures).
INSTALL a new fuel filter.
INSPECT the fuel injectors.
CLEAN the fuel injectors or
INSTALL a new set of injectors
as required only after the
checks have been carried out.
INSTALL a new fuel rail.
REFER to: Fuel
Injection
Supply Manifold (303-04C,
Removal and Installation).
REFER to: Engine Emission
Control (303-08 Engine Emission Control
- 2.OL
Duratec-HE (M14), Diagnosis .
and Testing). I
CKP sensor. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
KS. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
INSPECT the fuel injectors.
CLEAN the fuel injectors or
l NSTALL a new set of injectors
as required only after the
checks have been carried out.
Catalytic converter blocked.
Fuel
rail fuel pressure sensor.
REMOVE and visually
INSPECT the catalytic
converter for damage.
INSTALL a new catalytic
converter as necessary.
Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
REFER to: Catalytic Converter
I
- 1.8L Duratec-HE (M14)/2.OL
Duratec-H E (M14) (309-00,
Removal and Installation).
2006.0 Fiesta 1212006 GI 65371 en
procarmanuals.com

Fuel Charging and Controls - 2.OL
303-048-1 8 Duratec-HE (M14) 303-048-1 8
DIAGNOSIS AND TESTING
Symptom Possible Sources
Action -
lncorrector contaminated fuel. CHECK
for signs of
tion such as strange odors from
the fuel tank.
If contaminated fuel is found,
DRAIN the complete fuel
system. FLUSH the
through with clean gasoline.
REFER to: Fuel Tank Draining
(31
0-OOA, General Proced-
u res).
INSTALL a new fuel filter.
INSPECT the fuel injectors.
CLEAN the fuel injectors or
INSTALL a new set of injectors
as required only after the
checks have been carried out.
INSTALL a new fuel rail.
REFER to: Fuel Injection
Supply Manifold
(303-04C,
Removal and Installation). -- -
Positive crankcase ventilation
(PCV) system.
Worn or damaged valve
guide(s), piston ring(s), cylinder
bore(s), cylinder head or
gasket. INSPECT
for visible signs of
damage or blockage. CLEAN,
REPAIR or INSTALL new parts
as necessary.
REMOVE the cylinder head.
INSPECT the cylinder head,
pistons and cylinder bores for
signs of wear or damage.
REFER to: Cylinder Head (303-
01 C, In-vehicle Repair).
2006.0 Fiesta 1212006 GI 65371 en
procarmanuals.com

Fuel Charging and Controls - 2.OL
303-04B-19 Duratec-HE (M14) 303-04B-19
DIAGNOSIS AND TESTING
White smoke
Possible Sources Action
Incorrect or contaminated fuel. CHECK for signs of contamina-
tion such as strange odors from
the fuel tank.
If contaminated fuel is found,
DRAIN the complete fuel
system. FLUSH the fuel system
through with clean gasoline.
REFER to: Fuel Tank Draining
(31
0-OOA, General Proced-
u res).
INSTALL a new fuel filter.
INSPECT the fuel injectors.
CLEAN the fuel injectors or
INSTALL a new set of injectors
as required only after the
checks have been carried out.
INSTALL a new fuel injection
supply manifold.
REFER to: Fuel Injection
Supply Manifold
(303-04C,
Removal and Installation).
Coolant in the combustion
chamber. CARRY OUT a cooling system
pressure test.
REFER to: Engine Cooling
(303-03C, Diagnosis and
Testing).
REMOVE the cylinder head.
INSPECT the cylinder head,
cylinder head gasket and
cylinder bores for wear or
damage. REFER to: Cylinder Head (303-
01
C, In-vehicle Repair).
2006.0 Fiesta 1212006 GI 65371 en
procarmanuals.com

Fuel Charging and Con
Duratec-HE
(N
trols - 2.OL
14)
DIAGNOSIS AND TESTING
Symptom
Engine misfire
Possible Sources Action
Engine ignition. REFER to: Engine Ignition
(303-078, Diagnosis and
Testing).
Incorrect or contaminated fuel. CHECK for signs of contamina-
tion such as strange odors from
the fuel tank.
If contaminated fuel is found,
DRAIN the complete fuel
system. FLUSH the fuel system
through with clean gasoline.
REFER to: Fuel Tank Draining
(31
0-OOA, General Proced-
u res).
INSTALL a new fuel filter.
INSPECT the fuel injectors.
CLEAN the fuel injectors or
INSTALL a new set of injectors
as required only after the
checks have been carried out.
INSTALL a new fuel rail.
REFER to: Fuel Injection
Supply Manifold
(303-046,
Removal and Installation).
Low fuel system pressure. Check the fuel system pres- ( sure.
REFER to: Fuel System Pres-
sure Check (31
0-OOA,
General Procedures).
EGR valve sticking open. REFER to: Engine Emission
Control (303-08 Engine
Emission Control
- 2.OL
Duratec-HE (M14), Diagnosis
and Testing).
Engine operating temperature
too high. REFER to:
Engine Cooling
(303-03C, Diagnosis and
Testing).
ECT sensor. Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS.
CKP sensor.
Carry out a full engine
diagnosis using the guided diagnostic menu in WDS.
CMP sensor. Carry out a full
engine
diagnosis using the guided
diagnostic menu in WDS.
KS.
2006.0 Fiesta 1212006 GI 65371 en
Carry out a full engine
diagnosis using the guided
diagnostic menu in WDS. )I
procarmanuals.com