head FORD FIESTA 2007 Manual PDF

Engine - 1.25L Dura
303-01 A-I 28 Duratec-16V
(Sigma)/l .r
:eel 6V (Sigma)ll.4L
L
Duratec-1 6V (Sigma) 303-01A-128
INSTALLATION
37. Connect the gearshift actuator electrical All vehicles
connector (colored black). 41. Lower the vehicle.
42. Tighten the engine front mount retaining
nuts and bolts.
38. Install the gearshift actuator cover.
39. Connect the clutch slave cylinder supply
line.
Install the spring clip.
40. Bleed the hydraulic clutch system.
For additional information, refer to: Clutch
System Bleeding
- Vehicles With:
Automated Gearshift
(308-00 Manual
~ransmission/Transaxle and Clutch -
General Information, General Procedures).
43. N0TE:lnstall a new engine rear mount
center retaining nut.
Tighten the engine rear mount center
retaining nut.
44. Attach the power steering line support
bracket to the cylinder head.
2006.0 Fiesta 1212006 GII 31 64en
procarmanuals.com

303-01 A-I 29 Engine
- 1.25L Duratec-I
6V (Sigma)ll.4L
Duratec-I 6V (Sigma)/l .6L Duratec-1 6V (Sigma) 303-01A-129
INSTALLATION
45. Attach the power steering line to the power 48.
Connect the engine coolant temperature
i steering pump mounting bracket. (ECT) sensor electrical connector.
46, Install the engine wiring harness support 49.
Connect the generator electrical
brackets. connectors.
Connect the engine ground cable.
50. Connect the air conditioning (AIC)
47. Connect the electronic ignition (El) coil lower-pressure
cut-off switch electrical
electrical connector. connector.
51. Install the right-hand
headlamp assembly.
For additional information, refer to:
Headlamp Assembly (41 7-01 Exterior
Lighting, Removal and Installation).
2006.0 Fiesta 1212006 GI 131 64en
procarmanuals.com

Engine - I .25L Duratec-1 6V (Sigma)ll.4L
303-01 A-1 32 Duratec-1 6V (Sigma)ll .6L
Duratec-1 6V (Sigma) 303-01 A-1 32
INSTALLATION
64. Attach the coolant expansion tank to the
67. Attach the power steering fluid reservoir to
bracket. the bracket.
1'
65. Using the special tool, connect the degas
68. Tighten the strut and spring assembly top
hose to the cylinder head.
mount nuts on both sides.
66. Attach the fuel line and the degas line to
69. Connect the powertrain control module
the intake manifold.
(PCM) electrical connector.
Install the cable tie. For additional information, refer to:
Powertrain Control Module (PCM)
- 1.25L
Duratec-1 6V (Sigma)ll.4L Duratec-1 6V
(Sigma)ll .6L Duratec-1 6V (Sigma) (303-14
Electronic Engine Controls, Removal and
Installation).
70. Install the air cleaner.
For additional information, refer to: Air
Cleaner
- 1.25L Duratec-1 6V (Sigma)ll.4L
Duratec-1 6V (Sigma)ll .6L Duratec-1 6V
(Sigma) (303-12 Intake Air Distribution
and Filtering, Removal and Installation).
71. Install the front wheels and tires.
For additional information, refer to: Wheel
and Tire (204-04 Wheels and Tires,
c,
Removal and Installation). (\,
2006.0 Fiesta 121zo06 GII 31 64en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01A-I42 Duratec-1 6V (Sigma)/l .6L Duratec-I 6V (Sigma)
INSTALLATION
48. Attach the engine ground cable to the
transaxle. 52.
Connect the generator electrical
connectors.
49. Connect the electronic ignition (El) coil
53. Connect the knock sensor
(KS) electrical
electrical connector. connector.
50. Connect the engine coolant temperature
54. Connect the EVAP electrical connector.
(ECT) electrical connector.
51. Install the right-hand
headlamp assembly.
For additional information, refer to:
Headlamp Assembly (41 7-01 Exterior
Lighting, Removal and Installation).
2006.0 Fiesta 1212006 G380459en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-1 43 Duratec-1 6V (Sigma)/l.GL Duratec-1 6V (Sigma) 303-01 A-I
43
INSTALLATION
55. Connect the engine wiring harness 58. Connect the catalyst monitor sensor
electrical connector. electrical connector.
i
56. Attach the power steering line to the power 59. Connect the heated oxygen (H02S) sensor
steering pump mounting bracket. electrical
connector.
57. Attach the power steering line support 60. Using the special tool, connect the coolant
bracket to the cylinder head. hose
to the coolant distribution housing.
2006.0 Fiesta 1212006 G380459en
procarmanuals.com

Engine - 1.25L Duratec-1 6V (Sigma)ll.4L
303-01 A-I 44 Duratec-I 6V (Sigma)ll .6L Duratec-1 6V (Sigma) 303-01 A-1 44
INSTALLATION
61. Using the special tool, connect the coolant
hose to the coolant distribution housing. 64. Attach the coolant expansion tank to the
bracket.
/
62. Attach the brake booster vacuum line to 65. Using the special tool, connect the degas
the intake manifold.
hose to the cylinder head.
63. Connect the low pressure evaporate 66. Attach the power steering fluid reservoir to
emission (EVAP) hose to the EVAP valve.
the bracket.
2006.0 Fiesta 12/2006 G380459en
procarmanuals.com

303-01 B-I Engine -- 2.OL Duratec-HE (M14) 303-01 B-1
SECTION 303-01 B Engine . 2.OL Duratec-HE (M14)
VEHICLE APPLICATION:2006.0 Fiesta
CONTENTS
SPECIFICATIONS
........................................................................\
.............................................. Specifications
Engine Data
........................................................................\
............................................
Engine Oil ........................................................................\
...............................................
........................................................................\
............................................... Oil system
Engine Oil Capacity
........................................................................\
................................
Valve Dimensions ........................................................................\
...................................
Camshaft Dimensions ........................................................................\
.............................
Crankshaft Dimensions ........................................................................\
...........................
Piston Dimensions ........................................................................\
..................................
Cylinder Head ........................................................................\
.........................................
Cylinder Block ........................................................................\
.........................................
PAGE
DESCRIPTION AND OPERATION
Engine ........................................................................\
......................................................... 303-01 8-8
DIAGNOSIS AND TESTING
Engine ........................................................................\
.........................................................
GENERAL PROCEDURES
........................................................................\
....................... Valve Clearance Adjustment
IN-VEHICLE REPAIR
Intake Manifold ........................................................................\
................. (21 183 0)
Crankshaft Front Seal ........................................................................\
............. (21 467 0)
Crankshaft Pulley ........................................................................\
................... (21 5720)
Valve Seals ........................................................................\
....................... (21 238 0)
Valves ........................................................................\
................................. (21 2154)
Camshafts ........................................................................\
.......................... (21 284 0)
Oil Pan ........................................................................\
................................. (21 154 0)
Oil Pump ........................................................................\
.............................. (21 714 0)
Crankshaft Rear Seal ........................................................................\
.......... (21 468 4)
Engine Front Cover ........................................................................\
............. (21 148 0)
Exhaust Manifold ........................................................................\
........................................
Timing Chain ........................................................................\
........................ (21 314 0)
Cylinder Head ........................................................................\
....................... (21 163 0)
REMOVAL
Engine ........................................................................\
.........................................................
DISASSEMBLY
Engine ........................................................................\
................................ (21 134 8)
procarmanuals.com

Engine - 2.OL Duratec-HE (M14)
SPECIFICATIONS
I Service fill including filter I 4.3 I
Engine Oil Capacity
I Service fill excluding filter I 3.9 I
Description
Initial fill, including oil filter
Valve Dimensions Liters
4.6
Camshaft Dimensions Description
Valve
clearance (engine cold), intake
Valve clearance (engine cold), exhaust
Valve stem diameter, intake
Valve stem diameter, exhaust
mm
0.22 - 0.28
0.27
- 0.33
5.470
- 5.485
5.465
- 5.480
I Camshaft journal clearance I 0.035 - 0.080 I
Description
Camshaft journal diameter
I Camshaft endplay I 0.09 - 0.24 I
mm
24.97 + 0.01
Camshaft lobe lift, intake
Camshaft lobe lift, exhaust
Piston Dimensions
8.8
7.7
Description
Crankshaft endplay
Crankshaft Dimensions
mm
0.335 + 0.1 15
Cvlinder Head Description
Piston diameter - Class 1
Piston diameter - Class 2
Piston diameter - Class 3
1 a CAUTI0N:The mating face
of the cylinder head must not be reworked. mm
87.465 - 87.475
87.475
- 87.485
87.485
- 87.495
I Description I mm I
I Maximum distortion (mating face) I 0.1 I
2006.0 Fiesta 1u2006
Cylinder Block
'(, ',
Description
Cylinder bore diameter
Cylinder block distortion (maximum)
mm
87.500 + 0.030
0.
I
procarmanuals.com

303-01 B-5 Engine - 2.OL Duratec-HE (M14) 303-01 B-5
SPECIFICATIONS
Torque Specifications - --- -- - -- -
Description Nm l b-ft Ib-in
Air cleaner retaining bracket
Air cleaner resonator support bracket retaining bolts Battery cable to generator electrical connector
I Cylinder head retaining bolts I a) I - I - I
Battery tray support bracket retaining bolts
I
--
I Camshaft bearing caps retaining bolts a) IT
15
15
I Camshaft sprocket retaining bolts I 72 I 53 I - I
25
I Camshaft position (CMP) sensor retaining bolt I 6 1 - I 53 I
11
I1
-
-
18
I Engine front cover lower blanking plug I 12 I 9 I - I
-
Engine front cover retaining bolts
Engine front cover upper blanking plug
I Engine support insulator retaining bolts I 48 I 35 I - I
Engine wiring harness bracket to valve cover
retaining nut
a)
10
I Generator upper retaining bolt I 25 I 18 I - I
-
-
I Coolant plugs (4) to cylinder head I 75 I 55 I - I
-
89
Hood latch lever retaining bolts
Crankshaft pulley retaining bolts
Coolant expansion tank retaining nut
Coolant plug to cylinder block
I Power steering pump retaining bolt I 23 I 17 I - I
15
a)
8
43
I
--
I Power steering bracket retaining nut 15 IT
Power steering reservoir retaining bolts
Power steering pipe to the power steering
Power steering supply line to intake manifold
retaining bolt
11
-
-
32
Power steering high-pressure line retaining bracket
retaining bolt
-
-
71
-
9
65
I Power steering return line support bracket retaining I 15 I 11 I - I
1 nut
-
48 80 -
Exhaust
manifold bracket retaining bolts
2006.0 Fiesta 1212006 G451278en
Exhaust manifold upper heat shield retaining bolts
Exhaust manifold lower heat shield retaining bolts
Exhaust manifold to the cylinder head retaining nuts
Exhaust manifold studs to cylinder head
25
10
10
55
17 18
-
-
-
41
13 89
89 -
-
procarmanuals.com

303101 B-9 Engine - 2.OL Duratec-HE (M14) 303-01 B-9
DESCRIPTION AND OPERATION
The complete engine is made of cast aluminum
which, when combined with the plastic intake
manifold, gives a very light unit.
2.OL Duratec-HE (M14) engine
Emission standard
N0TE:Due to the fine tolerance in the bearing
clearances and bearing shells, no service
operations whatsoever are permitted on the crank
assembly. In the event of damage, the complete
cylinder block and crank assembly must be
changed. European
Emissions Standard Stage
IV (Stage II I, depending
on country)
Further design features include a ladder frame
incorporating the main bearing caps which support
the crankshaft in the cylinder block, and the
deep-drawn side walls of the cylinder block which
reduce engine vibration.
The camshafts are driven by a pinned link chain
which runs very quietly and is also
maintenance-free.
Cvlinder head
Item Description
1
2
The engine management for the 2.OL Duratec-HE
(M14) is provided by a Visteon system.
Item Description
Exhaust camshaft
Camshaft bearing cap
', This engine management systems controls the ' , sequential multipoint fuel injection (SFI) and the
I 1 (Enngine code I
3
4
wl~n~ine serial number I
Cam to identify cylinder No. 1
Intake camshaft
ele~tronically controlled coolant-cooled exhaust The design and the valve arrangement in the gas recirculation (EGR) valve.
cylinder head is similar to the head of the Zetec-SE
engines.
Enaine codes
5
The engine code and the engine serial number are
stamped on the right-hand side of the cylinder block
on the flywheel side of the engine. Camshaft sprockets
Cvlinder
head gasket
Item Description
I 1 I Cylinder head gasket I
1 2 1 Locating dowels 1
A four-layer laminated steel cylinder head gasket
is used.
The cylinder head gasket and cylinder head are
located with two locating dowels.
2006.0 Fiesta 1212006 G461395en
procarmanuals.com