check oil FORD MUSTANG 1969 Volume One Chassis

07-01-04
General Transmission Service

07-01-04

taching bolts to the proper torque. If

necessary, replace the gasket.

Check the fluid filler tube connec-

tion at the transmission case or pan.

If leakage is found here, install a new

O-ring or tighten the fitting to the

specified torque.

Check the fluid lines and fittings

between the transmission and the

cooler in the radiator tank for loose-

ness,
wear, or damage. If leakage can-

not be stopped by tightening a fitting,

replace the damaged parts.

Check the engine coolant in the ra-

diator. If transmission fluid is present

in the coolant, the cooler in the radia-

tor is probably leaking.

The cooler can be further checked

for leaks by disconnecting the lines

from the cooler fittings and applying

50-75 psi air pressure to the fittings.

Remove the radiator cap to relieve the

pressure build at the exterior of the oil

cooler tank. If the cooler is leaking

and will not hold this pressure the

cooler must be replaced. Cooler re-

placement is described in the Cooling

System Section of Group 11.

If leakage is found at either the

downshift control lever shaft or the

manual lever shaft, replace either or

both seals.

Inspect the pipe plug on the left

side of the transmission case at the

front. If the plug shows leakage, tor-

que the plug to specifications. If tight-

ening does not stop the leaks, replace

the plug. On a C6 transmission, a TV

pressure plug is also provided on the

right rear side of the case.

When converter drain plugs leak,

remove drain plugs with a six-point

wrench. Coat the threads with FoMo-

Co Perfect Seal Sealing Compound or

its equivalent, and install the plugs.

Torque the drain plugs to specifica-

tion. Fluid leakage from the converter

housing may be caused by engine oil

leaking past the rear main bearing or

from oil gallery plugs, or power steer-

ing oil leakage from steering system.

Be sure to determine the exact cause

of the leak before repair procedures

are started.

Oil-soluble aniline or fluorescent dyes

premixed at the rate of 1/2 teaspoon

of dye powder to 1/2 pint of transmis-

sion fluid have proved helpful in locat-

ing the source of the fluid leakage.

Such dyes may be used to determine

whether an engine oil or transmission

fluid leak is present or if the fluid in

the oil cooler leaks into the engine

coolant system. A black light, how-

ever, must be used with the fluorescent

dye solution.
DISHED OR

FLAT WASHER

" O.D.,
a" STEEL PLATE

5/8"X \W,

DRILL TO SUIT
HEX. HEAD SCREW

3/8"-24 X Vl

HEX. NUT W—
24

WELD

TOGETHER

WING
NUT

>/2"_13
THREAD

CHAIN,
10"
LONG
RUBBER PLUG

1
Vi" DIA. X 2"

LONG Vl"

HOLE THRU

APPROXIMATELY

40 DUROMETER
FLAT WASHER

Vs" O.D.

PLUG

VALVE
STANDARD BOLT

W-13
X 4Vl"

LONG SQUARE

THREAD
END

REMOVE HEAD

AND WELD
TO

WASHER

STANDARD 1/8" FITTING-87971-S FOR

RETAPPED DRAIN PLUG THREADS-USE

1/4" OVERSIZE FITTING-87973-S

D 1067-B
WELD TOGETHER

SECURELY—MUST

NOT LEAK

FIG. 2—Converter Leak Checking Tool

CONVERTER LEAKAGE

CHECK

If there are indications that the

welds on the torque converter are

leaking, the converter will have to be

removed and the following check

made before the unit is replaced.

A leak checking tool (Fig. 2) can be

made from standard parts. The tool

can be used to check all converters.

1.
Install the plug in the converter

(Fig. 3) and expand it by tightening

the wing nut. Attach the safety chains.

2.
Install the air valve in one of the

drain plug holes.

3.
Introduce air pressure into the

converter. Check the pressure with a

tire gauge and adjust it to 20 psi.

4.
Place the converter in a tank of

water. Observe the weld areas for

bubbles. If no bubbles are observed, it

may be assumed that the welds are

not leaking.

ENGINE IDLE SPEED CHECK

Check and, if necessary, adjust the

engine idle speed, using the procedure

given in Group 10.

If the idle speed is too low, the en-

gine will run roughly. An idle speed

that is too high will cause the vehicle

to creep, have harsh engagements and

harsh closed-throttle downshifts.
ANTI-STALL DASHPOT

CLEARANCE CHECK

After the engine idle speed has been

properly adjusted, check the anti-stall

dashpot clearance. Follow the proce-

dure given in Group 10 for checking

and adjusting this clearance.

MANUAL LINKAGE CHECKS

Correct manual linkage adjustment

is necessary to position the manual

valve for proper fluid pressure direc-

tion to the different transmission com-

ponents. Improperly adjusted manual

Tire Pressure Gauge

D1921-A

FIG. 3—Converter Leak Checking

Tool Installationprocarmanuals.com

07-01-06
General Transmission Service

07-01-06

MAKE MARK HERE

BELLOWS INTACT
BELLOWS FAILED

FIG. 9—Checking Vacuum Unit Bellows

tester equipped with a vacuum pump

(Fig. 8). Set the regulator knob so

that the vacuum gauge reads 18 inches

with the end of the vacuum hose

blocked off.

Then connect the vacuum hose to

the transmission vacuum unit. If the

gauge still reads 18 inches, the vacuT

urn unit diaphragm is not leaking. As

the hose is removed from the trans-

mission vacuum unit, hold a finger

over the end of the control rod. When

the hose is removed, the internal

spring of the vacuum unit should push

the control rod outward.

ALTITUDE

COMPENSATING-TYPE

The vacuum diaphragm should be

checked for ruptured or damaged bel-

lows.
Check the diaphragm assembly

as follows:

1.
Remove the diaphragm and

throttle valve rod from the transmis-

sion.

2.
Insert a rod into the diaphragm,

making sure that the rod is buttonec

in the hole. Make a reference mark on

the rod where it enters the diaphragm

hole.

3.
Hold the assembly in such a way

that the end of the rod is resting on

the weighing surface of a scale (Fig.

9).

4.
Gradually press down on the dia-

phragm assembly until the rod is

pressed into the diaphragm body. If

the reference mark on the rod is still
visible with 12 pounds of force regis-

tered on the scale, the bellows are in-

tact. If the mark disappears before 4

pounds of force is exerted, the bellows

have failed and the diaphragm must

be replaced. If the bellows are intact,

then perform various pressure checks.

SHIFT POINT CHECKS

Check the minimum throttle up-

shifts in D. The transmission should

start in first gear, shift to second, and

then shift to third, within the shift

points specified in the specification

section.

While the transmission is in third

gear, depress the accelerator pedal

through the detent (to the floor). The

transmission should shift from third to

second or third to first, depending on

the vehicle speed.

Check the closed throttle downshift

from third to first by coasting down

from about 30 mph in third gear. The

shift should occur within the limits

specified in the specification section.

When the selector lever is at 2, the

transmission can operate only in sec-

ond gear.

With the transmission in third gear

and road speed over 30 mph, the

transmission should shift to second

gear when the selector lever is moved

from D to 2 to 1. The transmission

will downshift from second or third to

first gear when this same manual shift

is made below approximately 25 mph

with a C4 transmission, 30 mph with
D 1791.A

a C6 transmission or 35 mph with an

FMX transmission. This check will

determine if the governor pressure and

shift control valves are functioning

properly.

During the shift point check opera-

tion, if the transmission does not shift

within specifications or certain gear

ratios cannot be obtained, refer to the

Ford Car and Truck Diagnosis Manu-

al to resolve the problem.

AIR PRESSURE CHECKS

A NO DRIVE condition can exist,

even with correct transmission fluid

pressure, because of inoperative

clutches or bands. Erratic shifts could

be caused by a stuck governor valve.

The inoperative units can be located

through a series of checks by subst-

ituting air pressure for the fluid pres-

sure to determine the location of the

malfunction.

To make the air pressure checks,

drain the transmission fluid and re-

move the oil pan and the control valve

body assembly. The inoperative units

can be located by introducing air pres-

sure into the transmission case passa-

ges leading to the clutches, servos, and

governor (Figs. 10, 11 or 12).

HYDRAULIC SYSTEM BENCH

TESTS (FMX TRANSMISSION)

After the transmission has been as-

sembled and is ready for installationprocarmanuals.com

07-01-08
General Transmission Service

07-01-08

3.
Install the bench testing tool on

the transmission.

4.
Remove the
1/8-inch
pipe plug

at the transmission case. Turn the

front pump in a clockwise direction at

75-100 rpm until a regular flow of

transmission fluid leaves the hole in

the transmission case. This operation
bleeds the air from the pump.

5.
Install the pressure gauge (77820

or T57L-77820-A) as shown in Fig.

13.

PRESSURE TESTS

Turn the front pump at 75-100 rpm
and note the gauge readings. The

pressure readings on the bench test

must be within the limits as outlined

in Figure 13, for the engine idle check.

If pressure gauge readings are with-

in limits in all selector lever positions,

install the vacuum diaphragm control

rod unit.

COMMON ADJUSTMENTS AND REPAIRS

TRANSMISSION FLUID DRAIN

AND REFILL

Normal maintenance and lubrica-

tion requirements do not necessitate

periodic automatic transmission fluid

changes.

If a major repair, such as a clutch

band, bearing, etc., is required in the

transmission, it will have to be re-

moved for service. At this time the

converter, transmission cooler and

cooler lines must be thoroughly

flushed to remove any dirt.

When filling a dry transmission and

converter, install five quarts of fluid.

Start the engine, shift the selector

lever as outlined below, and check and

add fluid as necessary.

Following are the procedures for

partial drain and refill due to in-

vehicle repair operation.

C4 TRANSMISSION

1.
On PEA models, disconnect the

fluid filler tube from the transmission

oil pan to drain the fluid.

On PEB and PEE models, loosen

the pan attaching bolts to drain the

fluid from the transmission.

2.
When the fluid has stopped

draining from the transmission, re-

move and thoroughly clean the pan

and the screen. Discard the pan gas-

ket.

3.
Place a new gasket on the pan,

and install the pan on the transmis-

sion.

4.
On PEA models, connect the

filler tube to the pan and tighten the

fitting securely.

5.
Add three quarts of fluid to the

transmission through the filler tube.

6. Run the engine at idle speed for

about two minutes, and then run it at

fast idle speed (about 1200 rpm) until

it reaches it's normal operating temp-

erature. Do not race the engine.

7.
Shift the selector lever through

all the positions, place it at P, and

check the fluid level. The fluid level

should be above the ADD mark. If
necessary, add enough fluid io the

transmission to bring the level be-

tween the ADD and FULL marks on

che dipstick. Do not overfill the trans-

mission.

FMX OK C6

TRANSMISSION

1.
Raise the vehicle on a hoist or

jack stands.

2.
Place a drain pan under the

transmission.

3.
Loosen the pan attaching bolts

to drain the fluid from the transmis-

sion.

4.
After the fluid has drained to the

level of the pan flange, remove the

rest of the pan bolts working from the

rear and both sides of the pan to

allow it to drop and drain slowly.

5.
When the fluid has stopped

draining from the transmission, re-

move and thoroughly clean the pan

and the screen. Discard the pan gas-

ket.

6. Place a new gasket on the pan,

and install the pan on the transmis-

sion.

7.
Add three quarts of fluid to the

transmission through the filler tube.

8. Run the engine at idle speed for

about two minutes, and then run it at

fast idle speed (about 1200 rpm) until

it reaches normal operating tempera-

ture.
Do not race the engine.

9. Shift the selector lever through

all the positions, place it at P, and

check the fluid level. The fluid level

should be above the ADD mark. If

necessary, add enough fluid to the

transmission to bring the level be-

tween the ADD and FULL marks on

the dipstick. Do not overfill the trans-

mission.

OIL COOLER TUBE

REMOVAL AND INSTALLATION

When fluid leakage is found at the

oil cooler, the cooler must be re-

placed. Cooler replacement is de-

scribed in the Cooling System Section

of Group 11.
When one or more of the fluid

cooler steel tubes must be replaced,

each replacement tube must be fabri-

cated from the same size steel tubing

as the original line.

Using the old tube as a guide, bend

the new tube as required. Add the

necessary fittings, and install the tube.

After the fittings have been tight-

ened, add fluid as needed, and check

for fluid leaks.

VACUUM DIAPHRAGM

ADJUSTMENT NON-ALTITUDE

COMPENSATING TYPE

The C4 and C6 transmissions are

equipped with an adjustable vacuum

diaphragm assembly. A similar ad-

justable diaphragm has been released

for service with the FMX transmis-

sion. However, the FMX service dia-

phragm is not interchangeable with

that used on C4 and C6 models.

The vacuum diaphragm assembly

has an adjusting screw in the vacuum

hose connecting tube (Fig. 14).

SPRING

SEAT

THIS CLEARANCE CHANGED

BY ADJUSTING SCREW

D1830-A

FIG. 14—Adjustable Vacuum Unit

The inner end of the screw bears

against a plate which in turn bears

against the vacuum diaphragm spring.

All readings slightly high or all

readings slightly low may indicate the

vacuum unit needs adjustment to cor-

rect a particular shift condition.procarmanuals.com

07-01-12
General Transmission Service

07-01-12

the transmission,
any
metal particles

or clutch plate
or
band material that

may have been carried into
the
cooler

should
be
removed from
the
system
by

flushing
the
cooler
and
lines before

the transmission
is put
back into serv-

ice.
In no
case should
an
automatic

transmission having
a
clutch
or
band

failure
or
other internal trouble result-

ing
in
fluid contamination,
be put

back into service without first flushing

the transmission
oil
cooler.

To flush
the oil
cooler, follow
the

instruct!
on >
provided with
the
Rotun-

da Automatic Transmission Torque

Converter
and
Cooler Cleaner
LRE-

60081.

INSPECTION

TURBINE
AND
STATOR
END

PLAY CHECK

A special tool
(Fig. 19)
must
be

used
to
check
the
condition
of the

converter. This special tool
is
used
to

check
the
turbine
and
stator
end
play

and
the
operation
of the
one-way
sta-

tor clutch.

CRUISE-O-MATIC

Too/-T58L-7902-A

C-4 AND C-6 TRANSMISSION

Tool-T59P.7902.Bor 7937-B

ON C-4 AND C-6 TRANSMISSION

Tool-T64L-7902-A
D
1499-E

FIG. 19—Converter Checking Tool

1.
Insert
the
tool (Fig.
19)
into
the

converter pump drive
hub
until
it
bot-

toms.

2.
Install
the
guide over
the con-

verter pump drive
hub.
3.
Expand
the
split fiber bushing
in

the turbine spline
by
tightening
the

adjusting
nut.
Tighten
the
adjusting

nut until
the
tool
is
securely locked

into
the
spline.

4.
Attach
a
dial indicator
to the

tool (Fig.
20 or
21). Position
the
indi-

cator button
on a
converter pump

drive
hub, and set the
dial face
at 0

(zero).

5.
Lift
the
tool upward
as far as it

will
go and
note
the
indicator reading.

The indicator reading
is the
total
end

play which
the
turbine
and
stator

share.
If the
total
end
play exceeds

the limits specified
in
Part 7-5, replace

the converter unit.

6. Loosen
the
adjusting
nut to
free

the split bushing,
and
then remove
the

tool from
the
converter.

STATOR ONE-WAY CLUTCH

CHECK

1.
Install
the
stator outer race hold-

ing tool
in one of the
four holes
pro-

vided
in the
stator (Fig.
20 or 21).

2.
Insert
the
tool
in the
converter

pump drive hub.
As the
tool enters
the

converter,
the
pins will engage
the sta-

tor clutch inner race spline.

3.
Place
a
torque wrench
on the

tool (Fig.
20 or
21).
The
tool (and
sta-

tor inner race) should turn freely

clockwise (from
the
pump drive
hub

inside
the
converter).
It
should lock
up

and hold
a 10
ft-lb pull when
the

wrench
is
turned counterclockwise.

Try
the
clutch
for
lockup
and
hold
in

at least five different locations around

the converter.
On
the
C4
or C6
Auto-

matics,
the
metal ring holding
the

locking tool will have
to be
held
by

hand during this check.

4.
If the
clutch fails
to
lock
up and

hold
a 10
ft-lb torque, replace
the

converter unit.

STATOR
TO
IMPELLER

INTERFERENCE CHECK

1.
Position
the
front pump assem-

bly
on a
bench with
the
spline
end of

the stator shaft pointing
up
(Fig.
22).

2.
Mount
a
converter
on the
pump

so that
the
splines
on the
one-way

clutch inner race engage
the
mating

splines
of the
stator support,
and the

converter
hub
engages
the
pump drive

gear.

3.
While holding
the
pump station-

ary, try
to
rotate the converter counter-

clockwise.
The
converter should
ro-

tate freely without
any
signs
of
inter-

ference
or
scraping within
the
convert-

er assembly.
4.
If
there
is an
indication
of
scrap-

ing,
the
trailing edges
of the
stator

blades
may be
interfering with
the

leading edges
of the
impeller blades.

In such cases, replace
the
converter.

STATOR
TO
TURBINE

INTERFERENCE CHECK

1.
Position
the
converter
on the

bench front side down.

2.
Install
a
front pump assembly
to

engage
the
mating splines
of
the
stator

support
and
stator,
and
pump drive

gear lugs.

3.
Install
the
input shaft, engaging

the splines with
the
turbine
hub (Fig.

23).

4.
While holding
the
pump station-

ary, attempt
to
rotate
the
turbine with

the input shaft.
The
turbine should
ro-

tate freely
in
both directions without

any signs
of
interference
or
scraping

noise.

5.
If
interference exists,
the
stator

front thrust washer
may be
worn,
al-

lowing
the
stator
to hit the
turbine.
In

such cases,
the
converter must
be re-

placed.

The converter crankshaft pilot

should
be
checked
for
nicks
or dam-

aged surfaces that could cause inter-

ference when installing
the
converter

into
the
crankshaft. Check
the con-

verter front pump drive
hub for
nicks

or sharp edges that would damage
the

pump seal.

OUTPUT SHAFT
AND

PRIMARY
SUN
GEAR SHAFT

(FMX TRANSMISSION)

1.
Inspect
the
thrust surfaces
and

journals
for
scores. Inspect
the
inter-

nal gear
for
broken
or
worn teeth.

2.
Inspect
the
aluminum sleeve
for

scores
or
leakage. Inspect
the
ring

grooves
for
burrs.

3.
Inspect
the
keyway
and
drive

ball pocket
for
wear,
and
inspect
the

splines
for
burrs, twist
or
wear.

4.
Inspect
the
output shaft sleeve

for alignment with
the
governor drive

ball (Fig.
24).

5.
Inspect
the
external parking gear

teeth
for
damage
and the
speedometer

drive gear teeth
for
burrs.

6.
If
either
the
output shaft
or
ring

gear
has
been replaced, place
the as-

sembled unit with
the
gear face down

on
the
bench, push
the
shaft down-

ward,
and
check
the
clearance
be-

tween
the top of the
snap ring
and its

groove
(Fig. 25).
If
this clearance
ex-

ceeds 0.002 inch, replace
the
snap ring

with
a
thicker ring
to
reduce
the
clear-

ance
to
less than 0.002 inch. Selectiveprocarmanuals.com

07-01-16
General Transmission bervice
07-01-16

CENTER SUPPORT

PLANETARY CLUTCH
"CAM TYPE" CLUTCH RACE

CHAMFER ON PRODUCTION

PART, ONLY-SERVICE PART NOT CHAMFERED
PLANET CARRIER

D1938-A

FIG. 27—Roller Type Planetary Clutch, Carrier and Center Support

shows wear or deterioration, replace

the seal.

4.
Inspect the seal counterbore and

remove all burrs and scores with cro-

cus cloth.

REAR CLUTCH (FMX)

AND REVERSE-HIGH CLUTCH

(C4 AND C6 AUTOMATIC)

1.
Inspect the drum band surface,

the bushing, and thrust surfaces for

scores. Minor scores may be removed

with crocus cloth. Badly scored parts

must be replaced.

Inspect the clutch piston bore and

the piston inner and outer bearing sur-

faces for scores. Check the air bleed

ball valve in the clutch piston for free

movement. Check the orifice to make

sure it is not plugged.

2.
Check the fluid passages for ob-

structions. All fluid passages must be

clean and free of obstructions.

3.
Inspect the clutch plates for wear

and scoring and check the plates for

fit on the clutch hub serrations. Re-

place all plates that are badly scored,

worn or do not fit freely in the hub

serrations.

4.
Inspect the clutch pressure plate

for scores on the clutch plate bearing

surface. Check the clutch release

spring(s) for distortion.

5.
On an FMX transmission, in-

spect the needle bearing for worn rol-

lers.

FRONT CLUTCH (FMX)

AND FORWARD CLUTCH

(C4 OR C6

TRANSMISSIONS)

1.
Inspect the clutch cylinder thrust

surfaces, piston bore, and clutch plate
serrations for scores or burrs. Minor

scores or burrs may be removed with

crocus cloth. Replace the clutch cylin-

der if it is badly scored or damaged.

2.
Check the fluid passage in the

clutch cylinder for obstructions. Clean

out all fluid passages. Inspect the

clutch piston for scores and replace if

necessary. Inspect the piston check

ball for freedom of movement and

proper seating (Fig. 28).

CLUTCH

CYLINDER

PISTON

SEAL
CLIP

D1939-A

. 28—Clutch Piston Check

Valve

3.
Check the clutch release spring

for distortion and cracks. Replace the

spring if it is distorted or cracked.
4.
Inspect the composition and the

steel clutch plates and the clutch pres-

sure plate for worn or scored bearing

surfaces. Replace all parts that are

deeply scored.

5.
On FMX and C4 transmissions,

check the clutch plates for flatness

and fit on the clutch hub serrations.

Discard any plate that does not slide

freely on the serrations or that is not

flat.

6. Check the clutch hub thrust sur-

faces for scores and the clutch hub

splines for wear.

7.
On an FMX transmission, in-

spect the turbine shaft bearing sur-

faces for scores. If excessive clearance

or scores are found, discard the unit.

Check the splines on the turbine

shaft for wear and replace the shaft if

the splines are excessively worn. In-

spect the bushing in the turbine shaft

for scores. On a C4 or C6 Automatic

transmission, check the input shaft for

damaged or worn splines.

FRONT PUMP AND

STATOR SUPPORT

1.
Inspect the mating surfaces of

the pump body and cover for burrs.

2.
Inspect the drive and driven gear

bearing surface for scores, and check

the gear teeth for burrs. Inspect the

stator support splines for burrs and

wear.

3.
Check the fluid passages for ob-

structions.

4.
If any parts other than the stator

support are found defective, replace

the pump as a unit. Minor burrs and

scores may be removed with crocus

cloth. The stator support is serviced

separately.

5.
On a C4 or C6 Automatic trans-

mission, check the oil ring grooves in

the stator support for nicks, burrs or

damaged edges. On a C6 transmis-

sion, check the large seal ring groove

of the pump body for damage. Check

the gasket mating surface of the pump

body for damage.

REAR SUPPORT

(FMX TRANSMISSION)

1.
Inspect the gasket mating sur-

faces for damage.

2.
Inspect the support bushing for

scores.

3.
Inspect the rear support fluid

passages for obstructions.

4.
Check the fit of the fluid tubes in

the support.procarmanuals.com

07-01-17
General Transmission Service
07-01-17

PRESSURE REGULATOR

(FMX TRANSMISSION)

1.
Inspect the regulator body and

cover mating surface for burrs.

2.
Check all fluid passages for ob-

structions.

3.
Inspect the control pressure and

converter pressure valves and bores for

burrs and scores. Remove all burrs

carefully with crocus cloth.

4.
Check free movement of the

valves in their bores. The valves

should fall freely into the bores when

both the valve and bore are dry.

5.
Inspect the valve springs and

spacers for distortion.

CONTROL VALVE BODY

1.
Clean all parts thoroughly in

clean solvent, and then blow them dry

with moisture-free compressed air.

2.
Inspect all valve and plug bores

for scores. Check all fluid passages for

obstructions. Inspect the check valve

for free movement. Inspect all mating

surfaces for burrs or distortion. In-

spect all plugs and valves for burrs

and scores. Crocus cloth can be used

to polish valves and plugs if care is

taken to avoid rounding the sharp

edges of the valves and plugs.

3.
Inspect all springs for distortion.

Check all valves and plugs for free

movement in their respective bores.

Valves and plugs, when dry, must fall

from their own weight in their respec-

tive bores.

4.
Roll the manual valve on a flat

surface to check it for a bent condi-

tion.

GOVERNOR

1.
Inspect the governor valves and

bores for scores. Minor scores may be
removed from the valves with crocus

cloth. Replace the governor if the

valves or body is deeply scored.

2.
Check for free movement of the

valves in the bores. The valves should

slide freely of their own weight in the

bores when dry. Inspect fluid passages

in the valve body and counterweight

for obstructions. All fluid passages

must be clean.

3.
Inspect the mating surfaces of

the governor body and governor dis-

tributor (C4 or C6 Automatic) for

burrs and distortion. Mating surfaces

must be smooth and flat.

4.
Check the mating surface of the

governor valve and the counterweight

on a FMX transmission for burrs or

scratches.

5.
When cleaning the governor as-

sembly (C4 Automatic), the oil screen

should be removed from the collector

body and thoroughly blown out with

compressed air.

FRONT SERVO (FMX)

AND INTERMEDIATE

SERVO (C4 AND C6

AUTOMATIC)

1.
Inspect the servo bore for cracks

and the piston bore and the servo pis-

ton stem for scores. Check fluid pas-

sages for obstructions. Replace seals

that are damaged.

2.
On an FMX transmission, check

the actuating lever for free movement,

and inspect it for wear. If necessary to

replace the actuating lever or shaft,

remove the retaining pin and push the

shaft out of the bracket.

Inspect the adjusting screw threads

and the threads in the lever for dam-

age.

3.
Check the servo spring and servo

band strut(s) for distortion.

4.
Inspect the cover seal and gasket

cover sealing surface for defects.
REAR SERVO (FMX)

AND LOW-REVERSE SERVO

(C4 TRANSMISSION)

1.
Inspect the servo body for cracks

and the piston bore for scores.

2.
Check the fluid passages for ob-

structions.

3.
Inspect the band and the struts

for distortion. Inspect the band ends

for cracks.

4.
Inspect the servo spring for dis-

tortion.

5.
Inspect the band lining for exces-

sive wear and bonding to the metal

band.

6. On an FMX transmission, check

the servo body to case mating surface

for burrs. Check the accumulator pis-

ton and the check valve for freedom

of movement. Check the actuating

lever socket for scores.

7.
Replace seals that are damaged.

CASE

Inspect the case for cracks and

stripped threads. Inspect the gasket

surfaces and mating surfaces for

burrs.
Check the vent for obstructions,

and check all fluid passages for ob-

structions and leakage (Figs. 10, 11

and 12).

Inspect the case bushing for scores.

Check all parking linkage parts for

wear or damage.

ONE-WAY CLUTCH

1.
Inspect the outer and inner races

for scores or damaged surface area

where the rollers contact the races. If

the outer race on the C6 transmission

is damaged, the low-reverse clutch hub

must be replaced.

2.
Inspect the rollers and springs

for excessive wear or damage.

3.
Inspect the spring and roller case

for bent or damaged spring retainers.procarmanuals.com

07-02^01

C4 Automatic Transmission
0702-01

PART 7-2 C4 Automatic
Transmission

PEA-A2 240-1V Column

PEA-MI 302-2V Column

PEA-N1 3O2-2V Console

PEB-B2 200-1V Console

PEB-C2 17O-1V,2OO-1V Column

PEE-M 302-2V Console

PEE-V 302-2V Column

PEE-AC 302-2V Console

PEE-AD 250-1V Console

PEE-AE 250-1V Column

PEE-AF 250-1V Console
MODEL APPLICATION
All
Models
Ford

X

X

X
Mercury
X

X

X
Meteor
Cougar
Fairiane

X

X

X

X
Falcon
X

X
Montego
X

X

X

X
Mustang
X

X

X
Lincoln-
Continental
Thunderbird
Continental-
Mark
III

COMPONENT INDEX

ASSEMBLY OF TRANSMISSION

BAND ADJUSTMENTS

Intermediate Band

Low-Reverse Band

CONTROL VALVE BODY

Cleaning and Inspection

Disassembly and Overhaul

Removal and Installation

DESCRIPTION

DISASSEMBLY AND OVERHAUL OF

TRANSMISSION

End Play Check

DOWNSHIFT LINKAGE

Adjustments

Parts Repair or Replacement

EXTENSION HOUSING

Cleaning and Inspection

Removal and Installation

EXTENSION HOUSING BUSHING

Removal and Installation

EXTENSION HOUSING REAR SEAL

Removal and Installation

FORWARD CLUTCH

Cleaning and Inspection

Disassembly and Overhaul

FORWARD CLUTCH HUB AND RING

GEAR

Disassembly and Overhaul

FRONT PUMP

Cleaning and Inspection

Disassembly and Overhaul

All
Models
02-27

02-09

02-09

01-16

02-19

02-11

02-02

02-12

02-12

02-04

02-17

01-14

02-10

02-10

02-10

01-15

02-24

02-25

01-15

02-21
COMPONENT INDEX

GOVERNOR AND OIL DISTRIBUTOR

Cleaning and Inspection

Disassembly and Overhaul

Removal and Installation

INTERMEDIATE SERVO

Cleaning and Inspection

Parts Repair or Replacement

Removal and Installation

INPUT SHELL AND SUN GEAR

Disassembly and Overhaul

LOW-REVERSE BRAKE DRUM BUSHING

Disassembly and Overhaul

LOW-REVERSE SERVO

Cleaning and Inspection

Parts Repair or Replacement

LOW-REVERSE SERVO PISTON

Removal and Installation

MANUAL LINKAGE

Adjustments

Parts Repair or Replacement

NEUTRAL START SWITCH-CONSOLE

SHIFT

Adjustment

Removal and Installation

(Refer to Part 7-1 for Column Shift Adjus

ment and Removal and Installation Pro-

cedures)

OIL PAN

Removal and Installation

REVERSE-HIGH CLUTCH

Cleaning and Inspection
All
Models
01-16

02-26

02-10

01-16

02-16

02-09

02-25

02-26

01-16

02-16

02-09

02-04

02-17

02-04

02-07

02-09

01-15
procarmanuals.com

07-02-03

C4 Automatic Transmission

07-02-03

CONVERTER

FORWARD CLUTCH
PRIMARY GOVERNOR

CONVERTER

CHECK VALVE
ONE-WAY

CLUTCH

DRAIN-BACK

VALVE

FRONT LUBE

CONVERTER

PRESSURE

RELIEF VALVE
LOW AND

REVERSE

SERVO
AND DIRECT

CLUTCH

L

SECONDARY

GOVERNOR
INTERMEDIATE

BAND

ACCUMULATOR

VALVE
CUT-BACK
VALVE

2-3
BACK-OUT

VALVE

MAIN

REGU-

LATOR

VALVE
MANUAL
LOW

VALVE

1-2 SHIFT

VALVE

D2
VALVE
THROTTLE

MODULATOR

VALVE

THROTTLE

BOOST VALVE

PRESSURE

BOOSTER

VALVE

DOWNSHIFT VALVE

LINE

COASTING

BOOST

VALVE
ENGINE
MANIFOLD
VACUUM

LESS THAN
20
INCHES

PRIMARY

THROTTLE

VALVE

(CASE)
VACUUM

DIAPHRAGM

OIL
SCREEN

I) 1724-E

FIG. 3—Hydraulic Control Systemprocarmanuals.com

07-02-07
C4 Automatic Transmission

07-02-07

2.
Remove the selector lever handle

from the lever.

3.
Remove the trim panel from the

top of the console.

4.
Remove the cover and dial indi-

cator as an assembly.

5.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

6. Loosen the two combination

starter neutral and back-up light

switch attaching screws (Fig. 10).

7.
Move the selector lever back and

forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 10).

8. Place the transmission selector

lever firmly against the stop of the

neutral detent position.

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

Check for starting in the park posi-

tion.

11.
Turn the ignition key to the

ACC position and place the selector

lever in the reverse position and check

the operation of the back-up lights.

Turn the key off.

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the four attaching screws.

13.
Install the cover and dial indi-

cator.

14.
Install the trim panel on the top

of the console. Install the selector

lever handle.

MUSTANG

1.
With the manual lever properly

NEUTRAL
START

SWITCH

(D1439-A

FIG. 11—Neutral Start Switch

Adjustments—Console Shift—

Mustang
adjusted, loosen the two switch attach-

ing bolts (Fig. 11).

2.
With the transmission manual

lever in neutral, rotate the switch and

insert the gauge pin (No. 43 drill

shank end) into the gauge pin holes of

the switch. The gauge pin has to be

inserted to a full 31/64 inch into the

three holes of the switch (Fig. 11).

3.
Torque the two switch attaching

bolts to specification. Remove the

gauge pin from the switch.

4.
Check the operation of the

switch. The engine should start only

with the transmission selector lever in

Neutral and Park.

NEUTRAL START SWITCH

REPLACEMENT—CONSOLE SHIFT

On vehicles equipped with a column

mounted neutral start switch, refer to

Part 7-1, Section 2, for the replace-

ment procedures.

FORD-METEOR

1.
Remove the four screws and

plates securing the selector lever

handle to the lever. Remove the

handle and detent control.

2.
Remove the two screws from the

rear of the console top panel. Pull the

panel back to unhook it from the

front of the console and remove the

panel.

3.
Remove the two screws securing

the dial indicator assembly to the se-

lector lever housing and remove the

indicator assembly.

4.
Disconnect the neutral start

switch wires at the plug connector.

Remove the wires from under the re-

taining clip.

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing and remove the switch

(Fig. 9).

6. Position the neutral start switch

to the selector lever housing and in-

stall the two attaching screws.

7.
Adjust the neutral start switch as

outlined under the Neutral Start

Switch Adjustment procedures in this

section.

8. Connect the neutral start switch

wires to the plug connector. Position

the wires in the retaining clip and

close the clip.

9. Place the console top panel on

the console and install the retaining

screws.

10.
Position the selector lever de-

tent control and handle on the selector

lever and secure with the four plates

and attaching screws.

FAIRLANE-MONTEGO

1.
Remove the selector lever handle

from the lever.
2.
Remove the trim panel from the

top of the console.

3.
Remove the cover and dial indi-

cator as an assembly.

4.
Remove the four screws that se-

cure the selector lever retainer to the

selector lever housing. Lift the retainer

from the housing.

5.
Remove the two screws securing

the neutral start switch to the selector

lever housing. Disconnect the neutral

start switch wires at the plug connec-

tor and remove the switch.

6. Position the neutral start switch

to the selector lever housing and in-

stall the two attaching screws.

7.
With the selector lever in neu-

tral,
move the selector lever back and

forth until the gauge pin (No. 43 drill)

can be fully inserted into the gauge

pin holes (Fig. 10).

8. Place the transmission selector

lever firmly against the stop of the

neutral detent position.

9. Slide the combination starter

neutral and back-up light switch for-

ward or rearward as required, until

the switch actuating lever contacts the

selector lever.

10.
Tighten the switch attaching

screws and remove the gauge pin.

11.
Connect the neutral start switch

wires to the plug connector and check

for starting in the park position.

12.
Position the selector lever re-

tainer to the selector lever housing.

Install the attaching screws.

13.
Install the cover and dial indi-

cator.

14.
Install the trim panel on the top

of the console. Install the selector

lever handle

MUSTANG

1.
Remove the downshift linkage

rod from the transmission downshift

lever.

2.
Apply penetrating oil to the

downshift lever shaft and nut. Remove

the transmission downshift outer lever

retaining nut and lever (Fig. 11).

3.
Remove the two neutral start

switch attaching bolts.

4.
Disconnect the multiple wire

connector. Remove the neutral switch

from the transmission.

5.
Install the neutral start switch on

the transmission. Install the two at-

taching bolts.

6. With the transmission manual

lever in neutral, rotate the switch and

install gauge pin (No. 43 drill) into

the gauge pin hole (Fig. 11).

7.
Tighten the switch attaching

bolts to specification and remove the

gauge pin.procarmanuals.com

07-02-09
C4 Automatic Transmission

07-02-09

11.
Remove the handle from the se-

lector lever.

12.
Install the selector housing and

lever assembly as shown in Figure 8.

Torque the attaching bolts 4-6 ft-lbs.

13.
Connect the dial indicator light.

14.
Install the pointer back-up

shield on the housing and lever assem-

bly.

15.
Install the dial housing and

tighten the attaching screws.

16.
Install the selector lever handle

and tighten the attaching screw.

17.
Position the selector lever in the

D position.

18.
Raise the vehicle. Install the

transmission manual lever rod to the

selector lever. Adjust the manual link-

age.

19.
Lower the vehicle and check the

transmission operation in each selo:c-

tor lever detent position.

BAND ADJUSTMENT

INTERMEDIATE BAND

1.
Clean all the dirt from the band

adjusting screw area. Remove and dis-

card the locknut.

2.
Install a new locknut on the ad-

justing screw. With the tool shown in

Fig. 13, tighten the adjusting screw

until the tool handle clicks. The tool is

a pre-set torque wrench which clicks

and overruns when the torque on the

adjusting screw reaches 10 ft-lbs.

I D1854-A

FIG. 13—Adjusting Intermediate

Band

Tool-T59P-77370-B

D1855-A

FIG. 14—Adjusting Low-Reverse

Band
3.
Back off the adjusting screw ex-

actly 1 3/4 turns.

4.
Hold the adjusting screw from

turning and torque the lock nut to

specification.

LOW-REVERSE BAND

1.
Clean all the dirt from the band

adjusting screw area. Remove and dis-

card the locknut.

2.
Install a new locknut on the ad-

justing screw with the tools shown in

Fig. 14, tighten the adjusting screw

until the tool handle clicks. The tool is

a pre-set torque wrench which clicks

and overruns when the torque on the

adjusting screw reaches 10 ft-lbs.

3.
Back off the adjusting screw ex-

actly 3 full turns.

4.
Hold the adjusting screw from

turning and torque the lock nut to

specification.

OIL PAN AND CONTROL

VALVE BODY REPLACEMENT

1.
Raise the vehicle so the trans-

mission oil pan is accessible.

2.
Drain the transmission fluid.

If the same fluid is to be used

again, filter the fluid through a 100

mesh screen. Re-use the fluid only if it

is in good condition.

3.
Remove the transmission fluid

pan attaching bolts, pan and gasket.

4.
Remove the valve body-to-case

attaching bolts (Fig. 25). Remove the

valve body from the case and the

transmission inner control levers.

5.
Refer to the Major Repair Oper-

ation for control valve body repair op-

eration.

6. Thoroughly clean and remove all

the gasket material from the pan and

the pan mounting face of the case. In-

stall the valve body to the case, engag-

ing the transmission inner control le-

vers with the valve body manual and

downshift valves.

7.
Install the eight valve body to

case attaching bolts. Torque the bolts

to specification. Operate the external

manual and downshift levers to check

for proper travel of the valve body

manual and downshift valves.

8. Place a new gasket on the pan.

Install the pan and attaching bolts.

Torque the bolts to specification. In-

stall the fluid filler tube if it was re-

moved. Torque the attaching nut to

specifications.

9. Lower the vehicle and fill the

transmission with fluid. Check the

transmission pan area for fluid leak-

age.
INTERMEDIATE SERVO

REPLACEMENT

1.
Raise the vehicle and remove the

four servo cover-to-case attaching

bolts.

2.
Remove the servo cover, gasket,

piston, and piston return spring. Re-

move the piston from the cover (Fig.

45).

3.
Remove the piston seals and

cover gasket.

4.
Install new piston seals on the

piston. Lubricate the piston seals with

clean transmission fluid. Install the

servo piston in the cover.

5.
Install the piston retvrn spring in

the case. Place a new gasicet on the

cover. Install the piston and cover into

the transmissic se. Use two 5/16

18 x 1 1/4 bolts, 180 degrees apart to

position the cover against the case.

6. Install the two servo cover at-

taching bolts. Remove the two 1 1/4

inch bolts and install two attaching

bolts.
Torque the bolts to specifica-

tion.

7.
Adjust the intermediate band.

Lower the vehicle and check the trans-

mission fluid level.

8. If the band can not be adjusted

properly, the struts are not in posi-

tion. Remove the pan and valve body.

Install the struts, valve body, pan, and

adjust the band. Refill the transmis-

sion with fluid.

LOW-REVERSE SERVO

PISTON REPLACEMENT

1.
Raise the vehicle on a hoist.

2.
Loosen the reverse band adjust-

ing screw lock nut. Tighten the reverse

band adjusting screw to 10 ft-lbs tor-

que.
(Tightening the screw will insure

that the band strut will be held against

the case by the band, preventing it

from falling down when the reverse

servo piston assembly is removed).

3.
Remove the four servo cover to

case attaching bolts. Remove the iden-

tification tag and vent tube retaining

clip.
Remove the servo cover and s»»^

from the case.

4.
Remove the servo piston from

the case. The piston seal cannot be re-

placed, without replacing the piston.

The seal is bonded to the piston.

5. To remove the piston from the

stem, insert a small screw driver in the

hole of the piston (Fig. 44). Remove

the piston attaching nut.

6. Position the accumulator spring

and spacer (Fig. 43) on the piston

stem. Make sure the crowned side of

the spring is facing toward the rod.

Install.a new piston on the piston re-

taining shaft. Install the attaching nut.

Torque the nut to specification.procarmanuals.com