door lock GEELY MK 2008 Workshop Manual

Table of ContentsV Section 1 SRS General Information ............................................................................... 5-54
Chapter 7 Air Conditioning System................................................................................... 5-72
Section 1 General Information ........................................................................................ 5-72
Section 2 Refrigerant ...................................................................................................... 5-77
Section 3 A/C Operating Mechanism ............................................................................. 5-83
Section 4 Heater, Ventilation and Air Conditioning ........................................................ 5-86
Section 5 Layont of Air Conditioning Hose ..................................................................... 5-92
Section 6 Multi-wedge belt (Connecting Compressor and Crankshaft Pulley) .............. 5-93
Section 7 Compressor Assembly .................................................................................... 5-94
Section 8 Condenser Fan and Condenser Assembly .................................................... 5-96
Chapter 8 MK-60 ABS System........................................................................................... 5-99
Section 1 ABS Diagnosis ................................................................................................ 5-99
Section 2 ABS System Check ...................................................................................... 5-103
Section 3 Removal and Installation .............................................................................. 5-138
Section 2 Power Door Lock Control System ................................................................5-142Part 6 Interior & Exterior Trim and AccessoryChapter 1 Front Seat Assembly......................................................................................... 6-1
Chapter 2 Rear Row Seat Assembly................................................................................. 6-3
Chapter 3 Front Seat Belt................................................................................................... 6-5
Chapter 4 Rear Seat Belt.................................................................................................... 6-9
Chapter 5 Dashboard, Middle Console and Instrument Panel....................................... 6-11
Chapter 6 Windshield......................................................................................................... 6-16
Chapter 7 Rear Window Glass (with Defrosting Heater Wire)........................................ 6-20
Chapter 8 Side Inner Panel Trim........................................................................................ 6-22
Chapter 9 Roof Trim............................................................................................................ 6-25
Chapter 10 Front Door Interior Trim.................................................................................. 6-27
Chapter 11 Rear Door Interior Trim................................................................................... 6-30
Chapter 12 Front Bumper................................................................................................... 6-33
Chapter 13 Rear Bumper.................................................................................................... 6-35

Brief Introduction of Geely MK - Vehicle Configuration2-4Electric
deviceInterior
deviceAdjustable steering wheelRemark: - denote standard configuration Z - standard C - comfortable D - luxury S - dark interior trim
T - light colored interior trim R - mixed colorType Item Name
No.
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51Standard Comfortable Luxury
Single Disc Single Disc 6 Discs6 speakers (2 Tweeters) 6 speakers (2 Tweeters) 6 speakers (2 Tweeters)Front seat back trash bag
6/4 split foldable rear seat
Cable-controlled oil tank cap
Cable-controlled trunk
plastic
leather
Power window (with one-touch function)
Remote control central door lock
Power rearview mirror with turn signal lightSmart remote control key (control the closure of the
door and window and the delay of the vehicle lights)Adjustable intermittent wiper
On-board handsfree handset
Anti-clamp retractive power window
Central pointer type instrument
Temperature display
Hi-fi CD audio
MP3 function
Speaker
Freon-free A/C system
Air cleaner
ABS + EBD
Driver side airbag
Front passenger side airbag
Telescopic steering columnFront seat belt pretensioner /height adjustableRear row triple-person seat belt
Anti-glaze inner rearview mirror
Anti-explosion and anti-leak plastic oil tank
Rear windshield defroster function
High-mounted stop light
Four-door anti-impact beam
Digital display rear parking radar
Follow me home light delay systemSafety
device

Chapter 2 Usage and Maintenance of MK SeriesSection 1 Usage of MK Series1. Instrument Panel Overview1.Instrument Panel Outlet Vent
2. Instrument Panel
3.Upper Glove Compartment
(Front Passenger Airbag Cover)
4.Sunshade
5.Dome Light And Sunroof
Switch
6.Inside Rearview Mirror
7.Glove Box
8. Power Window Regulator
Switch
9. Manual Transmission Shift
Lever Or Automatic Transmis-
sion Shift Lever
10.Parking Brake Control Lever
11.Engine Hood Release Handle
12.Power Window Lock
13.Power Door Lock Switch1.Left Combination Switch
2.Right Combination Switch
3.Display
4.Audio
5.Short-Distance Odometer
Adjustment Button
6.Instrument Panel Brightness
Adjustment Switch
7.Hazard Warning Light
8.A/C Control Panel
9.Ash Tray
10.Defroster Switch
11.Cigarette Lighter
12.”A/C“ Switch
13.Ignition Switch
14.Tilt Steering Adjustment
Handle
15.Theft-Deterrent Indicator
16.Power Outside Rearview
Mirror Control SwitchUsage and Maintenance of MK Series - Usage of MK Series2-6

2-16......Inspect ......Replace7.5 15 22.5 30 37.5 45 52.5 60 67.5 75
0.5 1 1.5 2 2.5 3 3.5 4 4.5 5System Inspection itemX1000km
YearBraking
SystemBrake reservoir level
FunctionClearance between brake drum and brake liningBrake shoe sliding part and brake lining wearBrake drum wear and damage
Brake lining wear
Brake disc wear and damage
DamageFastening and damage of attachmentAbnormal noise at a jointNoise from joint,damage to arm and
shock absorber fluid leak and damageAbnormal noise at fixtureBrake
BoosterMaster brake cylinder,brakecylinder and brakecalipelBrake liguid leakFunction wear and damageBrake
Drum and
ShoeBrake Disc and
Brake LiningSuspen-sionSystemSpringAttachmentand JointSuspensionArm and
Shock
Absorber
Electri-
cal
SystemEngine
Body
and
Acces-
soryIgnition System
BatteryWiring Harnee and ClipLightingComblned InstrumentHorn,Wiper and
Washer
Defrost and
Power Door Lock
Engine
General
StatusDoor and Trunk LockHood
Seat
OthersStarting performance,abnormal noise,idle and acceleration
Valve clearance
Oil leakSpark plug working status
Lgnition time
Distributor air gap
Distributor cap condition
ConnectionFastening and damage of jointsFunction
Function
Function
FunctionLock FunctionFastening abnormal noise and damageSeat and seat belt status
LubricationUsage and Maintenance of MK Series - Maintenance Category and Content of MK Sedano
oo
o o o
o
o o ooo o
o o
ooo o
o o
o o
oo o
o o
oo o
o o
oo oo o
o o
o o
o o
o o
o o
o o
oo o o
o o ooo o
o o
oo o
o o
oo o
o o
oo o
o o
oo o
o o
oo o o
o o ooo o
o o
oo o
o o
oo o
o o
oo o
o o
oo o
o o
o o
ooo o
o o
oo oo oo oo o

3. Definition of multi-pin plug-in unit terminal
1. Prompt:
R- red Bl- blue Y - yellow B- black P- pink G- green W- white
O- orange Gr - gray Br- brown V- purple Lg- olive drab
The first letter indicates primary color
The second letter indicates stripe colorTerminal
number1 MIL C 10 NA
2 Engine oil pressure switch YG 1 P
3 Brake fluid GR 2 R
4 Park G 3 N
5 Right turn light GB 4 D
6NA 52
7 EBD 6 L
8 Charge WR 7
9NA 8NA
10 NA 9 Sidelight GW
11 Safety belt YR 10 Start BR
12 NA 11 B+
13 Engine GY 12IG ( + ) Y
14 Safety gasbag RY 13 GND
15 NA 14 NA
16 IG ( + ) 15Speed sensor earthing B
1 NA 16 Speed signal input YR
2 Left turn light GW 17 Speed sensor power supply RY
3 High beam (+) RB 18 Key (ODO/TRIP) G
4 High beam (-) RW 19 Key (adjust brightness) YG
5 Foglight Gr 20 Key COM B
6 Rear defrost YB 21 Fuel gauge V
7 NA 22 ABS R
8 NA 23 Tachometer BBL
9 Door-lock warning lamp RBL 24 Coolant temperature gauge YWA
BCCombination Instrument System -Wiring diagram of Combination Instrument and Location of Multi-pin Plug-in Terminal5-9Definition of terminalConductor
ColorTerminal
numberDefinition of terminalConductor
Color

5-69Notice
Work must be started 60s after the positive (+) and negative (-) terminal cables are detached from battery.
3) The airbag assembly shall be deployed according to the following procedures.
(1) Driver airbag assembly
a. Remove the knee bolster.
b. Remove the connector (yellow) that connecting the lower end of the clock spring with the wire harness
of the instrument panel (see the figure below).Notice
Remove the connector of the clock spring from the wire harness of the instrument, the connector will be
short circuited automatically, which can avoid the possible serious accident resulted from the deployment of
the diver airbag assembly due to static electricity.
c. Tie two 6m plus wire harnesses for deployment to the
adaptor wire harness of the airbag, and wrap the connecting points
with insulating tape for insulation.The other ends of the wire harness
for deployment are connected to each other (short circuited). Unex-
pected deployment resulted from static electricity shall be prevented.
d. From the yellow connector of the clock spring, lead the
airbag adapter wire harnesses out of the vehicle by means of the wire
harnesses for deployment (see the figure below).
e. To restrain the noise, close all the windows and doors and
put on the vehicle cover.Notice
The glass will likely break up if there is crack. Vehicle covers shall be put on.
f. Try to disconnect at a location far away from the vehicle the connector of the wire harness for deployment
of the driver airbag assembly, connect them with the two terminals of the battery removed from the
vehicle and deploy the airbag (see the figure below).Notice
Make sure there is no man inside or near the vehicle and then
carry out the operations.
After the driver airbag is deployed, the gas generator is of high
temperature. Keep it for 30 minutes until it gets cool for use.
If the driver airbag assembly cannot be deployed, discuss the
problem with the local Geely service station.Deployed
HarnessCovering the car g. The deployed driver airbag assembly shall be scrapped according to the scrapping procedures.
Deploy outside the vehicleNotice
Keep the airbag over 6m away from a obstacle or person and deploy the airbag in an open flat area.
Deployed the airbag outside the vehicle, avoid to do this job in the strong wind. In case of breeze, fire should
be against the wind.SRS (Supplemental Restraint System)-
SRS-General InformationDAB
Connector Horn
Connector

Centralized Controller System-
Function Inspectior5-133Chapter 12 Centralized Controller SystemSection 1 Function InspectiorI. Glass frame riser: 1. Glass frame riser may be operated to move within 60s after ignition switch is turned on or off; 60s after
ignition switch is turned off, glass frame riser cannot be operated to move;
2. Manual rise: press corresponding glass frame riser switch rise key, corresponding glass frame riser motor
works, glass frame rises, release rise key, it stops.
3. Manual fall: press corresponding glass frame riser switch fall key (hold time 300ms), corresponding glass
frame riser motor works, glass frame falls, release fall key, it stops.
4. Automatic fall: press corresponding glass frame riser switch fall key (hold time < 300 ms), corresponding
glass frame riser motor works, glass frame falls down to end; or fall down until rise key or fall key is pressed again.
Note:
During automatic fall of glass frame, if corresponding glass frame riser switch fall key is pressed down for more
than 300 ms, glass frame riser is changed to manual fall mode; if corresponding glass frame riser switch rise key
is pressed down for more than 300ms, glass frame riser stops work.
5. Remote window closing:
In case of remote protection, if a key is pressed down for more than 1s, perform glass frame riser automatic
rise action, left front, right front, left rear, right rear in turn.II. Central lock: 1. In case protection is deactivated, use a key to open left front door switch or press internal unlock switch to
open four door fasteners; close left front door switch, close four door fasteners.
2. Remote unlock /lock:
(1) Ignition switch opening
a. Press remote control unlock key to open four door fasteners;
b. Press remote lock key to close four door fasteners;
(2) Turn off ignition switch
a. Press remote unlock key to open four front door fasteners, at the same time turn light flashes once.
b. Press remote lock key to close four door fasteners, at the same time turn light flashes twice.
(3) When door is opened, press remote fastener, turn light will flash for three times, at the same time electric
horn beeps for three times.
(4) If the system is triggered in anti-theft condition, when remote unlock system exits protection state,
directional turn signal will flash for four times, at the same time, electric horn beeps for four times.
3. Automatic lock
When vehicle speed exceeds 30km/h, three doors will be closed.
4. Door lock priority
Central door lock should not act simultaneously with glass frame riser; when they conflict with each other,
central door lock acts with priority, while glass frame riser stops; after central door lock action is finished, glass
frame riser continue its work in previous condition.III. Front womdscreem wiper: After spray water signal is finished, the wiper acts twice.

IV. Post-defrost: 1. When engine speed exceeds 700rpm (ignition switch is turned on), defrost work is permitted.
2. Turn on defrost switch, perform defrost work for 12 minutes, if defrost switch is pressed down again during
defrost work, defrost work will stop.
3. During defrost, turn off ignition switch, cancel this defrost.V. Light control: 1. Headlight:
(1) After press remote lock key to close four doors, if remote lock key is pressed down again twice in
succession within in 2s, dipped headlight will extend lighting for 1 minute; if remote unlock key is
pressed down within 60s, dipped headlight control output will be turned off.
(2) During output of 60s low level, if ignition switch is turned on, low level output will stop.
2. Ceiling lamp:
(1) When any of the doors is opened, ceiling lamp illuminates; if door is not closed, ceiling lamp will be
turned off after 10 minutes of delay.
(2) For closing of all doors, ceiling lamp will go out after time delay of 30s;
(3) In case all doors are closed,and ceiling lamp illuminates,ignition switch is turned on,ceiling lamp goes
out.
(4) For remote unlock, ceiling lamp illuminates; in case all doors are closed and ceiling lamp illuminates,
remote lock ceiling lamp goes out.VI. Remote anti-theft 1. Protected state: press lock key on remote controller, while closing four doors, anti-theft indicator lamp will
flashes slowly, indicating that the system enters protected state, when the system is triggered, turn light of the
vehicle will flash, warning horn gives out alarm.
2. Cancel protection: press unlock key on remote controller, while opening left front door, anti-theft indicator
lamp flashes rapidly, if at least one of ignition switch, door is opened within 30 s, anti-theft indicator lamp will
go out; otherwise it will enter secondary anti-theft state.
3. Two stage type protection cancellation: while the system is in triggered state, press any key on the remote
controller, alarm sound will stop, however, the system is still in protected state, and car door is still locked; if the
system continues to receive invasion signal, alarm will ring again after brief stop. To cancel protection completely,
cancel alarm for the first time, then press unlock key once immediately;
4. Secondary anti-theft: after protection is cancelled, if any of ignition switch, door is not opened within 30s,
the system will restore alert status automatically, and lock the car door.
Distribution of centralized controller connector terminals:
Connector on wiring harness, as shown in the figure below (view from outgoing terminal):Centralized Controller System-
Function Inspectior5-134Centralized
controller

Centralized Controller System-Function Inspectior5-135Terminal No.
A1
3
4
5
6
7
8
9
10
11
14
15
19
20
21
22
24
26
27
28
29
30
31
32
33
34
35
36RY
YR
BBL
BR
BL
GR
WR
WB
BR
WG
BW
Gr
VY
BG
WG
BLW
BR
BY
BG
R
O
GR
WG
BLB
BLR
BLPower supply (+)
Speed sensor signal
Engine speed signal
IG2
Spray water signal wiper switch 7#Wiper intermittent position signal (+)
Right front door lamp switch
Left front door lamp switch
Hazard lamp switch
GND
Right rear door lamp switch
Left rear door lamp switch
Rear right glass regulator switch (down)
Rear right glass regulator switch (up)
Turn light switch (right turn)
Turn light switch (left turn)
Defrost switch
Left front door fastener unlocked signal
Left front door fastener locked signal
Anti-theft indicator lamp
Rear left glass regulator switch (down)
Rear left glass regulator switch (up)
Front right glass regulator switch (down)
Front right glass regulator switch (up)
Front left glass regulator switch (down)
Front left glass regulator switch (up)
GND
Antenna Definition of centralized controller terminals:Conductor color Terminal definitionConnector A
Connector B Connector C

Chapter 13 Door Glass Regulating and Power Door Lock ControlSection 1 Door Glass Regulating SystemI. Inspection1. Check basic function
(1) Ignition switch is turned "ON" or within 60 s after ignition switch is turned off.
a. Check when rise key of glass regulator switch is pressed, corresponding glass rises, when release, it stops
rising; when press fall key and hold it, corresponding glass falls, when release, it stops falling.
b. Check when glass regulator main control switch lock switch on driver side is pressed,except which on driver
side, other glass regulator switches do not act.
c. Automatic fall: press corresponding glass regulator switch fall key briefly,corresponding glass
regulator motor works, glass falls down to the end; or falls down until rise key or fall key is pressed again.
Notes:
During automatic glass down, if corresponding glass regulator switch fall key is pressed down and held,
glass regulator is changed into manual fall mode; if corresponding glass regulator switch rise key is pressed down
and held, glass regulator is changed into manual rise mode; if corresponding glass regulator switch rise or fall key
is pressed briefly, glass regulator stops work. Press briefly: less than 300ms; press and hold: more than 300 ms.
(2) Close window remotely.
In case setting protection remotely, if a key is pressed for more than 1s, glass regulator automatic window
rising action will be performed, implementation mode: left front, right front, left rear, right back, in the
process of window rise, only one glass regulator is permitted to act, only after glass regulator up to the top,
could the other glass riser act.
2. Glass reguelator switch on driver sideDoor Glass Regulating and Power Door Lock Control-Door Glass Regulating System5-136Glass regulator switch on driver side
Window on front passenger side
Window on driver side
Rear right window
Rear left window
Window locking switch