lock HONDA INTEGRA 1994 4.G Workshop Manual

Remove the 13 bolts securing the right side cover
and right side cover protector, then remove them.
Slip the special tool onto the mainshaft as shown.
MAINSHAFT HOLOER07GAB-PF50101
3. Engage the parking brake pawl with the parking gear.
4. Align the hole ot the sub-shaft l st gear with the hole
of the the transmission housing, then insert a pin to
lock the sub-shaft while removing the sub-shaft
locknut.
'1.
COUNTERSHAFTLOCKNUTReplace.
MAINSHAFTLOCKNUTReplace.
8 mm pin.
comm€rciallyavailable
SU8-SHAFTLOCKNUTReplace.
Align the holes.
CONICAL SPNINGWASHERSReplace.
5. Pry the lock tab of the mainshaft locknut.
6. Cut the lock tabs of the countershaft and sub-shaft
locknuts using a chisel as shown. Then remove the
locknut from each shatt.
NOTE;
a Mainshaft and countershaft locknuts have lett-
hand threads.
a Clean the old countershaft locknut, it is used to
install the parking gear on the countershaft.a Always wear safety glasses.
CAUTION:
Keop all of th€ chis€led panicles out of the
tlanamigsion.
llrF-"""*
,fl(,-..- LocKNUr
@-.**'o'
7.
8.
q
10.
11.
12.
13.
14.
15.
to.
Remove the lock pin that was installed to hold the
sub-shaft.
Remove the special tool from the mainshaft after
removing the locknut.
Remove the 1st clutch and mainshaft 1st gear as-
sembly from the mainshaft.
Remove the sub-shaft 1st gear,
Remove the parking brake pawl.
Using a universal two jaw puller. remove the park-
ing gea.. one-way clutch and counlershatt 1st gear
assembly.
PARKING GEAR
Remove the parking brake lever from the control
shaft.
Remove the throttle control lever from the throttle
control shaft.
Remove the ATF cooler pipes.
Remove the ATF level gauge.
14-111

NOTE:
a Clean all parts thoroughly in solvent o. carburetor
cleaner and d.y with compressed air.a Blow out all passages.
a When removing the transmission housing, replace the
following:. Transmission housing gasket. Lock washer
1. Remove the transmission mount b.acket.
Remove the transmission housing mounting bolts
and hanger.
Align the spring pin of the control shaft with the
transmission housing groove by turning the control
shaft.
Install the special tool on the transmission housing,
then remove the housing as shown.
HOUSING PUI-LER07HAC-PK4010A
2.
4.
6.
Remove the countershaft reverse gear with the col-
lar and needle bearing.
Remove the lock bolt securing the shitt fork. then
remove the fork with the reverse selector trom the
countershatt.
Remove the countershaft and mainshaft sub-
assembly together.
8. Remove the ditferential assemblv.
14-113

Torque Gonverter Housing/Valve Body
Removal
\LOCK-UP VALVE llB.DY\u
Bolts, 7
DOWEL PIN
otLFEEDPIPES
A
Ll
ll|i
|]V
OII- FEED PIPES
LOCK-UP SEPARATORPI.ATE
TOR COVER
OIL FEEO PIPE
8oll3.3
ATF STRAINER
SERVO DETENTBASEREGULATOR VALVEAODY
OIL FEED PIPES
DOWEL PIN
OIL PUMP DRIVEN GEAR SHAFT
OIL PUMP DRIVEN
SECONDARY VALVEBODY
DOWEL PIN
SECONDARY SEPARATORPLATE
SUCTION PIPECOLLAR
MAIN S€PARATORPLATE
ft-- rrr urcler
TOROUE CONVERTERHOUSING
8olts, 4 Boll
MAIII VALVEBODY
14-114

NOTE:
a Clean all parts thoroughly in solvent or carbuetor
cleaner and dry with compressed air.a Blow out all passages.
a When removing the valve body replace the following:. O-rings. Lock wsshers
1 . Remove the oil feed pipes from the servo body, s€r-
vo detent base, accumulatof cover, lock-uD valve
body and main valve body.
2, Remove the three bolts securing the ATF strainer and
servo detent base, then remove them.
3. Remove the three bolts securing the accumulator
cover. then remove the accumulator cover.
4. Remove the six bolts secu.ing the servo body, then
remove the servo body and separator plate.
5. Remove the bolt securing the secondary valve body,
then remove the secondary valve body and separa-
tor plate.
6. Remove the eight bolts securing the lubricator plate
and lock-up valve body, then remove the lubricatorplate, lock-up valve body and separator plate.
7. Femove the bolt securing the.egulator valve body,
then.emove the regulator valve body.
8. Remove the stator shaft and stopper shaft.
9. Remove the detent spring t,om the detent arm. thenremove the control shaft from the torque convenerhousing.
1O. Remove the detent arm and detent afm shaft t.om
the main valve bodv.
1 1 . Remove the four bolts secu.ing the main valve body,then remove the main valve body.
12. Remove the oil pump driven gear shaft, then remove
the oil pump gears.
'13. Remove the main separator plate with two dowelDtns.
14, Remove and clean the ATF magnet.
15.Clean the inlet opsning of the ATF strainer thorough-
ly with compressed air, then check that it is in good
condition, and the inlet opening is not clogged.
II{LET OPENING
Replace the ATF strainer it it is clogged or damaged.
NOTE: The ATF strainer can be reused if it is notclo9ged.
16.
14-115

Regulator Valve Body
Disassembly/lnspection/Reassembly
NOTE:
a Clean all pans thoroughly in solvent or carburetor cleaner, and dry with compressed ait.a Blow out all passages.
a Replace valve body as an assembly it any parts are worn or damaged.a Check all valves for free movement. lf any fail to slide freely, see Valve Body Repair on page 14-117.
1. Hold the .egulator spring cap in place while removing the lock bolt. Once the bolt is removed. release the spring
cap slowlv.
CAUTION: The .egulator spring c8p can pop out whsn the lock bolt is removod.
2. Reassembly is in the reverse order of the disassembly procedute.
NOTE:
. Coat all pans with ATF.
a Align the hole in the regulator spring cap with the hole in the valve body, press the spring cap into the body andtighten the lock bolt.
LOCK.BOLT6 x 1.0 mm12 N.m (1.2 kgl.m, 8.7 lbf.ftl
REGULATOR SPRING CAP
COOLER CHECK
OOWEL PINS, 2
ROLLER
SPRING SPECIFICATIONS
Unit of length: mm (in)
../
I',.-2" ll"%=
VALVE SLEEVE
t,-V
,*6t'"
REGULATOR VALVE
REGULATOR VALVE BODY
No.Spring
Standard (New)
Wiro Dia.o.D.Free LonglhNo. of Coils
o/a
@
\9/
Regulator valve spring A
Regulator valve spring B
Stator reaction spring
Lock-up control valve spring
Cooler check valve spring
Torque converter check valve spring
1.80 (O.O71)
1.80 (0.071)
5.50 (O.2171
o.80 (o.o31)
1 .10 (0.043)
1 .10 (O.O43t
14.70 (O.5791
9.60 (0.378)'26.40 (1.O39)
6.60 (O.260)
8.40 (O.331)
8.40 (0.331)
88.60 (3.488t
44.OO t't.7321
30.30 (1 .1 93t
39.50 (1.555)
33.80 (1 .331 I
33.80 (1 .331 )
16.5
2.1
25.O'l2.5
12.5
14-122
lnside Diameter

NOTE:
a Clean all paris thoroughly in solvent or carburetor cleaner, and dry with compressed air.
a Blow out all passages.
a Replace valve body as an assembly it any parts are worn or damaged.
a Check all valves tor free movement. lf any fail to slide fre€ly, see Valve Body Repair on page 14-117.
a Coat all parts with ATF before reassembly.
LOCK-UP SHIFT VALVE
LOCK.UP TIMING 8 VALVE
,ar
\,/
SPRING SPECIFICATIONS
CAP
Unit ot length; mm (in)
No.Spring
Standard {Nsw}
Wile Di8.o.D.Flee LengthNo. of Coils
o
@
Lock-up shift valve spring
Lock-up timing B valve spring
o.90 (o.035)
o.80 (o.031)7.60 (0.299)
6.60 {O.260)
73.70 i.2.9021
60.80 (2.394)32.O
22.1
Disassembly/lnspection/Reassembly
14-123

Mainshaft
Disassembly/lnspection/Reassembly
NOTE:
a Lubricate all pans with ATF during reassembly.
a Install the thrust needle bearings with unrolled edge of bearing retainer lacing washer.
a Inspect the thrust needle bearings and the needle bearings for galling and rough movement.
a Betore installing the O-rings, wrap the shaft splines with tape to prevent damaging the O-rings.
a Locknut has lett-hand threads.
RING
\
MAINSHAFTCheck splines tor excessivewear or damage.Check bearing surface for scoring,scralches or excessive wear,
CONICAL SPRING WASI{ERReplace.
LOCKNUT (FLANGE NUT)19 x 1.25 mm93 N.m {9.5 kgf.m, 69 lbf.ftlReplace.Left-hand threads
SNAP
THRUST WASHER
THRUST NEEDLEBEARING
lST CLUTCHASSEMBLY
o-ntNGsReplace.
THRUST WASHER
THRUST NEEDLEBEARING4TH GEAR
NEEOLE BEARIT{GS
4TH GEAR COLLAR
lST GEAR
THRUST WASHER
BEANING
1ST GEARCOLLAR
TRANSMISSIONHOUSING BEARING
SEALING RINGS,35 mm
2ND/4TH CLUTCHASSEMBLY
NEEDLE BEARING
THRUST NEEDLEBEARING
O.RINGSReplace.
THRUST WASHER, 36.5 x 55 mmSolective part.
THRUST NEEDLEBEAFING
2ND GEAR
SEALING RING.29 mm
NEEDLE BEARING
SET RII{G

Mainshaft
Inspection
a Clearance Measurement
NOTE: Lubricate all parts with ATF during assembly.
1 . Remove the mainshaft bearing lrom the transmission
housing (see page 14-152).
2. Assemble the parts below on the mainshaft.
NOTE: Do not assemble the O-rings while in-
specting.
LOCKNUT
/ 1ST CLUTCH ASSEMBLY
THRUST WASHER
lST GEAR COLLAR
TBANSMISSIONHOUSING BEARING
THRUST WASHER
4TH GEAR COLLAR
2ND/4TH CLUTCHASSEMBLY
THRUST WASHERSelective part.
TI{RUST NEEDLEBEARING
2ND GEAR
NEEDLE BEARING
THRUST NEEOLEBEARING
MAINSI.IAFT
14-130
3RD GEAR2ND GEAR
Torque the mainshaft locknut to 29 N.m (3.0
kgf .m, 22 lbf.ft).
NOTE: Mainshaft locknut has lett-hand threads.
29 N.m (3.0 kgl.m, 22 lbt.ft)
4. Hold 2nd gear against the 2nd clutch. then meas-
ure the clearance between 2nd gear and 3rd gear
with a feeler gauge.
NOTE: Take measurements in at least three Dlaces
and take the average as the actual clea.ance.
STANDARD: 0.05-0.13 mm {0.002-0.005 inl
THRUST WASHER-36.5 x 55 ftm
3RD GEAR 2ND GEAR

Countershaft
Disassembly/lnspection/Reassembly
NOTE:
a Lubricate all parts with ATF belore reassembly.a Install the thrust needle bearings with unrolled edge of bearing retainer facing washer.a Inspect the thrust needle bearings and the needle bearings tor galling and rough movement.a Before installing the O rings, wrap the shaft splines with tape to prevent damaging the O-rings.a Locknut has left-hand threads.
CONICAL SPRINGWASHERReplace.
LOCKNUT {FLANGE NUTI23 x 1.25 mm1O3-0-lO3N.m{10.5-O-'l0.5ksf.m,75.9*O-75.9tbf.fr)Replace.Left-hand threads
REVERSE GEAR COLLAR
NEEDLE EEARINGPARKING GEAR
ONE.WAYCLUTCHREVERSEGEAR
BEVERSESELECTOR
REVERSE SELECTORHUB
4TH GEAR
NEEDLE BEARING
DISTANCE COLLAR,28 mmSelective part.
.I ST GEAR
NEEDLE EEARING
lST GEAR COLLAR
TRANSMISSIONHOUSING BEARING
COUNTERSHAFTCheck splines for excessivewear or damage.Check bearing surface for scoring,scratches or excessive wear_
2ND GEAE
THRUST NEEDLEBEARING
3RD GEAR
NEEDLE BEARING
THRUST NEEDLE BEARING
3RD GEAR COLLAR
3RD CLUTCH ASSEMBLY
O-RINGSReplace.

Install the parts below on the countershaft sub-
assembly, then torque the locknut to 29 N'm (3.O
kgf.m, 22 lbf.ft).
LOCKNUTLeft-hand threads
CONICAL SPRI GWASHER
PARKING GEAR/ONE-WAYCLUTCH/1ST GEARASSEMBLY
NEEEDLE BEARING
lST GEAR COLLAR
TRANSMISSION HOUSINGBEARING
REVERSE GEARCOLLAR
Measure the clearance between the 2nd gear and
the distance collar, 28 mm wilh a feeler gauge.
NOTE: Take measurements in at least three places.
and take the average as the actual clearance.
STANDARD: O.O5-0.13 mm (0.OO2-O.O05 in)
DISTANCE COLLAR,28 mm2ND GEAR
2ND GEAR
(cont'd)
14-135