check INFINITI M35 2006 Factory Service Manual

AV-114
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
TROUBLE DIAGNOSIS
Revision: 2006 January2006 M35/M45
3. CHECK IMAGE SIGNAL
1. Connect DVD player connector and front display unit connector.
2. Turn ignition switch ON.
3. Display DVD image.
4. Check signal between DVD player harness connector M272 ter-
minal 20 and ground.
OK or NG
OK >> Replace front display unit.
NG >> Replace DVD player.
4. CHECK HARNESS BETWEEN AV (NAVI) CONTROL UNIT AND FRONT DISPLAY UNIT
1. Turn ignition switch OFF.
2. Disconnect AV (NAVI) control unit connector and front display unit connector.
3. Check continuity between AV (NAVI) control unit harness con-
nector (A) M210 terminal 50 and front display unit harness con-
nector (B) M203 terminal 2.
OK or NG
OK >> GO TO 5.
NG >> Repair harness or connector.
5. CHECK RGB AREA SIGNAL
1. Connect AV (NAVI) control unit connector and front display unit connector.
2. Turn ignition switch ON.
3. Shift the selector lever in R position.
4. Check signal between AV (NAVI) control unit harness connector
M210 terminal 50 and ground.
OK or NG
OK >> Replace front display unit
NG >> Replace AV (NAVI) control unit.20 – Ground:
SKIB4696E
SKIB2251J
50 – 2 : Continuity should exist.
SKIB4697E
50 – Ground:
SKIB4614E
PKIB4948J

TROUBLE DIAGNOSIS
AV-115
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 January2006 M35/M45
Warning Message of Whether Rear View Image Is Rolling or Not DisplayedNKS00495
1. CHECK HARNESS BETWEEN AV (NAVI) CONTROL UNIT AND FRONT DISPLAY UNIT
1. Disconnect AV (NAVI) control unit connector and front display unit connector.
2. Check continuity between AV (NAVI) control unit harness con-
nector (A) M210 terminals 51, 52 and display unit harness con-
nector (B) M203 terminals 4, 6.
3. Check continuity between AV (NAVI) control unit harness con-
nector (A) M210 terminals 51, 52 and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2. CHECK HORIZONTAL SYNCHRONIZING SIGNAL
1. Connect AV (NAVI) control unit connector and front display unit connector.
2. Turn ignition switch ON.
3. Check signal between AV (NAVI) control unit harness connector
M210 terminal 51 and ground.
OK or NG
OK >> GO TO 3.
NG >> Replace front display unit.
3. CHECK VERTICAL SYNCHRONIZING SIGNAL
Check signal between AV (NAVI) control unit harness connector
M210 terminal 52 and ground.
OK or NG
OK >> Replace AV (NAVI) control unit.
NG >> Replace front display unit.
DVD Operation Screen Is Not DisplayedNKS00496
Refer to AV- 11 5 , "Warning Message of Whether Rear View Image Is Rolling or Not Displayed" .
It Cannot Be Switched to DVD ModeNKS00497
Refer to AV- 11 6 , "DVD SOUND IS NOT OUTPUT" . 51 – 4 : Continuity should exist.
52 – 6 : Continuity should exist.
51, 52 – Ground : Continuity should not exist.
SKIB4698E
51 – Ground:
SKIB4699E
SKIB3601E
52 – Ground:
SKIB4700E
SKIB3598E

AV-116
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
TROUBLE DIAGNOSIS
Revision: 2006 January2006 M35/M45
Sound Is Not Output (Voice Guidance and TEL Voice Are Normal) NKS00498
DVD AND AUDIO SOUND ARE NOT OUTPUT
1. PERFORM CONSULT-II SELF-DIAGNOSIS
Perform “SELF-DIAG RESULT” of CONSULT-II and check the malfunction. Refer to AV- 1 0 3 , "
SELF-DIAG
RESULTS" .
OK or NG
OK >> GO TO 2.
NG >> Refer to AV- 1 0 3 , "
Display Item of SELF-DIAG RESULTS" .
2. CHECK AV COMM MONITOR
Select “AUDIO” of “AV COMM MONITOR”, and then check the displays of “TRANSMIT DG” and “SPEAKER
AMP”.
A or B
A >> Replace BOSE amp.
B >> Replace audio unit.
DVD SOUND IS NOT OUTPUT
1. PERFORM CONSULT-II SELF-DIAGNOSIS
Perform “SELF-DIAG RESULT” of CONSULT-II and check the malfunction. Refer to AV- 1 0 3 , "
SELF-DIAG
RESULTS" .
OK or NG
OK >> GO TO 2
NG >> Refer to AV- 1 0 3 , "
Display Item of SELF-DIAG RESULTS" .
2. CHECK AV COMM MONITOR
Select “AUDIO” of “AV COMM MONITOR”, and then check the displays of “TRANSMIT DG” and “DVD player”.
A or B
A >> Replace DVD player
B >> Replace audio unit.
Voice Activated Control System Is Not ActivatedNKS00499
THE SCREEN IS SWITCHED BY PRESSING THE STEERING SWITCH
1. VOICE MICROPHONE TEST
Turn “Voice Microphone Test” ON at Confirmation/Adjustment mode, and then check the sounds emitted from
the speaker. Refer to AV- 9 8 , "
Voice Microphone Test" .
Is the sound output?
YES >> Replace AV (NAVI) control unit.
NO >> GO TO 2A
TRANSMIT DG
SPEAKER AMP: OK
: UNKWN
B
TRANSMIT DG
SPEAKER AMP: UNKWN
: OK
A
TRANSMIT DG
DVD PLAYER: OK
: UNKWN
B
TRANSMIT DG
DVD PLAYER: UNKWN
: OK

TROUBLE DIAGNOSIS
AV-117
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 January2006 M35/M45
2. CHECK HARNESS BETWEEN AV (NAVI) CONTROL UNIT AND MIC.
1. Turn ignition switch OFF.
2. Disconnect AV (NAVI) control unit connector and MIC. connector.
3. Check continuity between AV (NAVI) control unit harness con-
nector (A) M78 terminals 6, 7, 8 and MIC. harness connector (B)
R52 terminals 4, 2, 1.
4. Check continuity between AV (NAVI) control unit harness con-
nector (A) M78 terminals 6, 7, 8 and ground.
OK or NG
OK >> GO TO 3.
NG >> Repair harness or connector.
3. CHECK MIC. POWER SUPPLY
1. Connect AV (NAVI) control unit and MIC. connector.
2. Turn ignition switch ON.
3. Check voltage between AV (NAVI) control unit harness connec-
tor M78 terminals 6 and 7.
OK or NG
OK >> GO TO 4.
NG >> Replace AV (NAVI) control unit.
4. CHECK MIC. SIGNAL
1. Check signal between AV (NAVI) control unit harness connector
M78 terminals 8 and 7.
OK or NG
OK >> Replace AV (NAVI) control unit.
NG >> Replace MIC.
THE SCREEN IS NOT SWITCHED BY PRESSING THE STEERING SWITCH
Refer to AV- 11 8 , "Steering Switch Cannot Be Operated" . 6 – 4 : Continuity should exist.
7 – 2 : Continuity should exist.
8 – 1 : Continuity should exist.
6, 7, 8 – Ground : Continuity should not exist.
SKIB4632E
6 – 7 : Approx. 5 V
SKIB4633E
8 – 7:Give a voice
SKIB4634EPKIB5037J

AV-118
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
TROUBLE DIAGNOSIS
Revision: 2006 January2006 M35/M45
Steering Switch Cannot Be OperatedNKS0049A
NONE OF THE OPERATIONS WORK.
1. CHECK HARNESS
1. Check continuity between spiral cable harness connector (A)
M303 terminal 17 and audio unit harness connector (B) M76 ter-
minal 15.
OK or NG
OK >> Replace steering switch.
NG >> Check spiral cable. If the malfunction is detected, repair
the harness and connector.
“ENTER”, “MENU UP-DOWN”, AND “SOURCE” SWITCHES ARE NOT OPERATED
1. CHECK HARNESS
1. Check continuity between spiral cable harness connector (A)
M303 terminal 20 and audio unit harness connector (B) M76 ter-
minal 6.
2. Check continuity between spiral cable harness connector (A)
M303 terminal 20 and ground.
OK or NG
OK >> GO TO 2.
NG >> Check spiral cable. If the malfunction is detected, repair
the harness and connector.
2. CHECK STEERING SWITCH SIGNAL A
1. Turn ignition switch ON.
2. Check voltage between audio unit harness connector M76 ter-
minals 6 and 15
OK or NG
OK >> Replace steering switch.
NG >> Replace audio unit.17 – 15 : Continuity should exist.
SKIB6278E
20 – 6 : Continuity should exist.
20 – Ground : Continuity should not exist.
SKIB4636E
6 – 15 : Approx. 5 V
SKIB4637E

TROUBLE DIAGNOSIS
AV-119
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 January2006 M35/M45
“PTT/TEL”, “BACK”, AND “VOLUME CONTROL” SWITCHES ARE NOT OPERATED
1. CHECK HARNESS
1. Check continuity between spiral cable harness connector (A)
M303 terminal 16 and audio unit harness connector (B) M76 ter-
minal 16.
2. Check continuity between spiral cable harness connector (A)
M303 terminal 16 and ground.
OK or NG
OK >> GO TO 2.
NG >> Check spiral cable. If the malfunction is detected, repair
the harness and connector.
2. CHECK STEERING SWITCH SIGNAL B
1. Turn ignition switch ON.
2. Check voltage between audio unit harness connector M76 ter-
minals 16 and 15
OK or NG
OK >> Replace steering switch.
NG >> Replace audio unit.
The Hands-Free Phone Cannot Be UsedNKS0049B
THE VOICE CANNOT BE HEARD
1. CHECK HARNESS AV (NAVI) CONTROL UNIT AND AUDIO UNIT
1. Disconnect AV (NAVI) control unit connector and audio unit connector.
2. Check continuity between AV (NAVI) control unit harness con-
nector (A) M78 terminals 10, 11 and audio unit harness connec-
tor (B) M77 terminals 30, 31.
3. Check continuity between AV (NAVI) control unit harness con-
nector (A) M78 terminals 10, 11 and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.16 – 16 : Continuity should exist.
16 – Ground : Continuity should not exist.
SKIB4638E
16 – 15 : Approx. 5 V
SKIB4639E
10 – 30 : Continuity should exist.
11 – 31 : Continuity should exist.
10, 11 – Ground : Continuity should not exist.
SKIB4640E

AV-120
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
TROUBLE DIAGNOSIS
Revision: 2006 January2006 M35/M45
2. CHECK TEL VOICE SIGNAL
1. Connect AV (NAVI) control unit connector and audio unit connector.
2. Turn ignition switch ON.
3. Check signal between AV (NAVI) control unit harness connector
M78 terminals 10 and 11
OK or NG
OK >> Replace audio unit.
NG >> Replace AV (NAVI) control unit.
THE VOICE CANNOT BE TRANSMITTED
Refer to AV- 11 6 , "THE SCREEN IS SWITCHED BY PRESSING THE STEERING SWITCH" .
Voice Guidance Is Not Heard (Base System)NKS0049C
1. CHECK HARNESS BETWEEN AV (NAVI) CONTROL UNIT AND AUDIO UNIT
1. Disconnect AV (NAVI) control unit connector and audio unit connector.
2. Check continuity between AV (NAVI) control unit harness con-
nector (A) M78 terminals 12, 14 and audio unit harness connec-
tor (B) M77 terminals 32, 33.
3. Check continuity between AV (NAVI) control unit harness con-
nector (A) M78 terminals 12, 14 and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2. CHECK VOICE GUIDANCE SIGNAL
1. Connect AV (NAVI) control unit connector and audio unit connector.
2. Turn ignition switch ON.
3. Push the voice button.
4. Check signal between AV (NAVI) control unit harness connector
M78 terminals 12 and 14.
OK or NG
OK >> Replace AV (NAVI) control unit.
NG >> Replace audio unit.10 – 11:When inputting TEL voice
SKIB4641ESKIB3609E
12 – 32 : Continuity should exist.
14 – 33 : Continuity should exist.
12, 14 – Ground : Continuity should not exist.
SKIB4702E
12 – 14:
SKIB4645E
SKIB3609E

TROUBLE DIAGNOSIS
AV-121
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 January2006 M35/M45
Voice Guidance Is Not Heard (BOSE System)NKS0049D
1. CHECK HARNESS BETWEEN AV (NAVI) CONTROL UNIT AND BOSE AMP
1. Disconnect AV (NAVI) control unit connector and BOSE amp connector.
2. Check continuity between AV (NAVI) control unit harness con-
nector (A) M78 terminals 12, 14 and BOSE amp harness con-
nector (B) B107 terminals 32, 12.
3. Check continuity between AV (NAVI) control unit harness con-
nector (A) M78 terminals 12, 14 and ground.
OK or NG
OK >> GO TO 2.
NG >> Repair harness or connector.
2. CHECK VOICE GUIDANCE SIGNAL
1. Connect AV (NAVI) control unit connector and BOSE amp connector.
2. Turn ignition switch ON.
3. Push the voice button.
4. Check signal between AV (NAVI) control unit harness connector
M78 terminals 12 and 14.
OK or NG
OK >> Replace AV (NAVI) control unit.
NG >> Replace BOSE amp.12 – 32 : Continuity should exist.
14 – 12 : Continuity should exist.
12, 14 – Ground : Continuity should not exist.
SKIB4644E
12 – 14:
SKIB4645E
SKIB3609E

TROUBLE DIAGNOSIS
AV-123
[WITHOUT MOBILE ENTERTAINMENT SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
AV
Revision: 2006 January2006 M35/M45
MAP DVD-ROM
ROUTE CALCULATION AND VISUAL GUIDANCE
The location of vehicle icon is mis-
aligned from the actual position.When using tire chains or replacing the tires, speed
calculations based on the speed sensor may be
incorrect.Drive the vehicle for a while [at approxi-
mately 30km/h (19 MPH) for about 30
minutes] to automatically correct the vehi-
cle icon position.
If this does not correct the vehicle icon
position, contact an INFINITI dealer.
The map data has mistake or is incomplete (the
vehicle icon position is always misaligned in the
same area).Updated road information will be included
in the next version of the map DVD-ROM. Symptom Possible cause Possible solution
Symptom Possible cause Possible solution
The message “Error” appears. Map DVD-ROM is dirty or partially damaged.Check the DVD-ROM and wipe it clean
with a soft cloth.
If there is any damage, replace the DVD-
ROM.
Symptom Possible cause Possible solution
In the auto reroute calculation,
waypoints are not included.Waypoints already passed are not included in the
auto reroute calculation.In case of going to that waypoints again,
edit the route.
Route information is not displayed.Route calculation has not yet been performed.Set the destination and perform route cal-
culation.
The vehicle is not driven on the suggested route. Drive on the suggested route.
Route guidance is set to off. Turn on route guidance.
Route information is not provided for narrow streets
(roads displayed in gray).This is not a malfunction.
The auto reroute calculation (or
detour calculation) suggests the
same route as the one previously
suggested. Route calculation took priority conditions into con-
sideration, but the same route was calculated. This is not a malfunction.
A waypoint cannot be added.Five waypoints are already set on the route, includ-
ing ones that already passed.A maximum of 5 waypoints can be set on
the route. In case of going to 6 or more
waypoints, perform route calculations mul-
tiple times as necessary.
The suggested route is not dis-
played.Roads near the destination cannot be calculated.Reset the destination to a main or ordinary
road, and recalculate the route.
The starting point and destination are too close. Set a more distant destination.
The starting point and destination are too far away.Divide the way by selecting one or two
intermediate destinations, and perform
route calculations multiple times.
There are time restricted roads (by day of week, by
time) near the current vehicle location or destina-
tion.Set “Use Time Restricted Roads” to off.
A part of the route is not displayed.The suggested route includes narrow streets (roads
displayed in gray).This is not a malfunction.
The part of the route already
passed is deleted.A route is managed by sections between way-
points. If you passed the first waypoint, the section
between the starting point and the waypoint is
deleted. (It may not be deleted depending on the
area.)This is not a malfunction.

AV-144
[WITH MOBILE ENTERTAINMENT SYSTEM]
PRECAUTION
Revision: 2006 January2006 M35/M45
[WITH MOBILE ENTERTAINMENT SYSTEM]PRECAUTION PFP:00011
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
NKS004A7
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WAR NING :
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for Trouble DiagnosisNKS004A8
AV COMMUNICATION SYSTEM
Do not apply voltage of 7.0 V or higher to the measurement terminals.
Use the tester with its open terminal voltage being 7.0 V or less.
Be sure to turn ignition switch OFF and disconnect the battery cable from the negative terminal before
checking the circuit.
Precautions for Harness RepairNKS004A9
AV COMMUNICATION SYSTEM
Solder the repaired parts, and wrap with tape. [Frays of twisted
line must be within 110 mm (4.33 in).]
Do not perform bypass wire connections for the repair parts.
(The spliced wire will become separated and the characteristics
of twisted line will be lost.)
PKIA0306E
PKIA0307E