INFINITI QX56 2009 Factory Service Manual

REAR WINDOW DEFOGGERDEF-43
< ON-VEHICLE REPAIR >
C
DE
F
G H
I
J
K
M A
B
DEF
N
O P
ON-VEHICLE REPAIR
REAR WINDOW DEFOGGER
Filament CheckINFOID:0000000003776364
1. When measuring voltage, wrap tin foil around the top of the neg- ative probe.Then press the foil against the wire with your finger.
2. Attach probe circuit tester (in Volt range) to middle portion of each filament.
3. If a filament is burned out, circuit tester registers 0 or battery voltage.
4. To locate burned out point, move probe to left and right along fil- ament. Test needle will swing abruptly when probe passes the
point.
Filament RepairINFOID:0000000003776365
REPAIR EQUIPMENT
• Conductive silver composition (DuPont No. 4817 or equivalent)
• Ruler 30 cm (11.8 in) long
SEL122R
SEL263
SEL265
Revision: December 20092009 QX56

DEF-44
< ON-VEHICLE REPAIR >
REAR WINDOW DEFOGGER
• Drawing pen
• Heat gun
• Alcohol
• Cloth
REPAIRING PROCEDURE
1. Wipe broken heat wire and its surrounding area clean with acloth dampened in alcohol.
2. Apply a small amount of conductive silver composition to tip of drawing pen.
Shake silver composition container before use.
3. Place ruler on glass along broken line. Deposit conductive silver composition on break with drawing pen. Slightly overlap existing
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
4. After repair has been completed, check repaired wire for conti- nuity. This check should be conducted 10 minutes after silver
composition is deposited.
Do not touch repaired area while test is being conducted.
5. Apply a constant stream of hot air directly to the repaired area for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours.
PIIA0215E
SEL012D
SEL013D
Revision: December 20092009 QX56

DLK-1
BODY EXTERIOR, DOORS, ROOF & VEHICLE SECURITY
C
DE
F
G H
I
J
L
M
SECTION DLK
A
B
DLK
N
O P
CONTENTS
DOOR & LOCK
WITH INTELLIGENT KEY SYSTEM
BASIC INSPECTION ....... .............................
6
DIAGNOSIS AND REPAIR WORKFLOW ..... .....6
Work Flow ........................................................... ......6
INSPECTION AND ADJUSTMENT .....................9
ADDITIONAL SERVICE WHEN REMOVING BAT-
TERY NEGATIVE TERMINAL ............................... ......
9
ADDITIONAL SERVICE WHEN REMOVING
BATTERY NEGATIVE TERMINAL : Description ......
9
ADDITIONAL SERVICE WHEN REMOVING
BATTERY NEGATIVE TERMINAL : Special Re-
pair Requirement ................................................. ......
9
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT .................................................... ......
9
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description ..................................
9
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement .......
9
FUNCTION DIAGNOSIS ..............................10
AUTOMATIC DOOR LOCKS ......................... ....10
System Diagram .................................................. ....10
System Description .................................................10
Component Parts Location ....................................12
Component Description ..........................................12
DOOR LOCK FUNCTION ..................................14
DOOR LOCK AND UNLOCK SWITCH ................. ....14
DOOR LOCK AND UNLOCK SWITCH : System
Diagram ...................................................................
14
DOOR LOCK AND UNLOCK SWITCH : System
Description ..............................................................
14
DOOR LOCK AND UNLOCK SWITCH :
Component Parts Location ....................................
15
DOOR LOCK AND UNLOCK SWITCH :
Component Description ..........................................
15
DOOR REQUEST SWITCH ................................... ....16
DOOR REQUEST SWITCH : System Diagram .......16
DOOR REQUEST SWITCH : System Description ....16
DOOR REQUEST SWITCH :
Component Parts Location ....................................
19
DOOR REQUEST SWITCH :
Component Description ..........................................
21
INTELLIGENT KEY ................................................ ....21
INTELLIGENT KEY : System Diagram ....................21
INTELLIGENT KEY : System Description ...............21
INTELLIGENT KEY : Component Parts Location ....24
INTELLIGENT KEY : Component Description ........25
BACK DOOR OPENER FUNCTION .................27
BACK DOOR OPENER SWITCH .......................... ....27
BACK DOOR OPENER SWITCH : System Dia-
gram ........................................................................
27
BACK DOOR OPENER SWITCH : System De-
scription ...................................................................
27
BACK DOOR OPENER SWITCH :
Component Parts Location ....................................
32
BACK DOOR OPENER SWITCH :
Component Description ..........................................
32
INTELLIGENT KEY ................................................ ....33
INTELLIGENT KEY : System Diagram ....................33
INTELLIGENT KEY : System Description ...............33
INTELLIGENT KEY : Component Parts Location ....35
INTELLIGENT KEY : Component Description ........36
WARNING FUNCTION ......................................38
System Description ..................................................38
Component Parts Location ....................................42
KEY REMINDER FUNCTION ............................44
System Description ..................................................44
Component Parts Location ....................................45
HAZARD AND BUZZER REMINDER FUNC-
TION ..................................................................
47
Revision: December 20092009 QX56

DLK-2
System Diagram .....................................................47
System Description .................................................47
Component Parts Location ...................................48
Component Description .........................................50
HOMELINK UNIVERSAL TRANSCEIVER ........51
Component Description ....................................... ...51
DIAGNOSIS SYSTEM (BCM) ............................52
COMMON ITEM ..................................................... ...52
COMMON ITEM : CONSULT-III Function (BCM -
COMMON ITEM) ................................................. ...
52
DOOR LOCK .......................................................... ...52
DOOR LOCK : CONSULT-III Function (BCM -
DOOR LOCK) .........................................................
52
MULTIREMOTE ENT ............................................. ...53
MULTIREMOTE ENT : CONSULT-III Function
(BCM - MULTIREMOTE ENT) ................................
53
INTELLIGENT KEY ................................................ ...55
INTELLIGENT KEY : CONSULT-III Function
(BCM - INTELLIGENT KEY) ...................................
55
DIAGNOSIS SYSTEM (INTELLIGENT KEY
UNIT) ............................................................... ...
56
CONSULT-III Function (INTELLIGENT KEY) ...... ...56
COMPONENT DIAGNOSIS ........................58
U1000 CAN COMM CIRCUIT ......................... ...58
Description ........................................................... ...58
DTC Logic ...............................................................58
Diagnosis Procedure ..............................................58
U1010 CONTROL UNIT (CAN) .........................59
DTC Logic ............................................................ ...59
Diagnosis Procedure ..............................................59
Special Repair Requirement ...................................59
INSIDE KEY ANTENNA 1 (REAR OF CEN-
TER CONSOLE) ............................................. ...
60
Description ........................................................... ...60
Component Function Check .................................60
Diagnosis Procedure ..............................................60
INSIDE KEY ANTENNA 2 (LUGGAGE COM-
PARTMENT) ......................................................
62
Description ........................................................... ...62
Component Function Check .................................62
Diagnosis Procedure ..............................................62
INSIDE KEY ANTENNA 3 (FRONT OF CEN-
TER CONSOLE) ................................................
64
Description ........................................................... ...64
Component Function Check .................................64
Diagnosis Procedure ..............................................64
INSIDE KEY ANTENNA 4 (OVERHEAD CON-
SOLE AREA) .....................................................
66
Description ........................................................... ...66
Component Function Check ..................................66
Diagnosis Procedure ...............................................66
POWER SUPPLY AND GROUND CIRCUIT .....68
INTELLIGENT KEY UNIT ....................................... ...68
INTELLIGENT KEY UNIT : Diagnosis Procedure ...68
BCM (BODY CONTROL MODULE) ..........................68
BCM (BODY CONTROL MODULE) : Diagnosis
Procedure ...............................................................
68
BACK DOOR .......................................................... ...69
BACK DOOR : Diagnosis Procedure ......................69
DOOR SWITCH .................................................71
Description ........................................................... ...71
Component Function Check ..................................71
Diagnosis Procedure ...............................................71
DOOR LOCK AND UNLOCK SWITCH .............74
DRIVER SIDE ......................................................... ...74
DRIVER SIDE : Description ....................................74
DRIVER SIDE : Component Function Check ........74
DRIVER SIDE : Diagnosis Procedure .....................74
PASSENGER SIDE ...................................................76
PASSENGER SIDE : Descripti on ...........................76
PASSENGER SIDE :
Component Function Check ............................... ...
76
PASSENGER SIDE : Diagnosis Procedure ............76
KEY CYLINDER SWITCH .................................79
Description ........................................................... ...79
Component Function Check ...................................79
Diagnosis Procedure ...............................................79
FRONT DOOR LOCK ACTUATOR LH (DOOR
UNLOCK SENSOR) ..........................................
81
Description ........................................................... ...81
Component Function Check ..................................81
Diagnosis Procedure ...............................................81
Component Inspection ............................................82
DOOR REQUEST SWITCH ...............................83
Description ..............................................................83
Component Function Check ..................................83
Diagnosis Procedure ...............................................83
Component Inspection ............................................84
DOOR LOCK ACTUATOR ................................86
DRIVER SIDE ......................................................... ...86
DRIVER SIDE : Description ....................................86
DRIVER SIDE : Component Function Check ........86
DRIVER SIDE : Diagnosis Procedure .....................86
PASSENGER SIDE ...................................................87
PASSENGER SIDE : Descripti on ...........................87
PASSENGER SIDE :
Component Function Check ............................... ...
87
Revision: December 20092009 QX56

DLK-3
C
DE
F
G H
I
J
L
M A
B
DLK
N
O P
PASSENGER SIDE : Diagnosis Procedure ........
....
87
REAR LH ............................................................... ....88
REAR LH : Description ............................................88
REAR LH : Component Function Check ...............88
REAR LH : Diagnosis Procedure ............................88
REAR RH ............................................................... ....89
REAR RH : Description ...........................................89
REAR RH : Component Function Check ...............90
REAR RH : Diagnosis Procedure ............................90
BACK DOOR ......................................................... ....91
BACK DOOR : Description ......................................91
GLASS HATCH LOCK ACTUATOR ..................92
Diagnosis Procedure ...............................................92
PASSENGER SELECT UNLOCK RELAY .........93
Description .......................................................... ....93
Component Function Check ....................................93
Diagnosis Procedure ...............................................93
INTELLIGENT KEY WARNING BUZZER ..........95
Description .......................................................... ....95
Component Function Check ..................................95
Diagnosis Procedure ...............................................95
Component Inspection ............................................96
OUTSIDE KEY ANTENNA .................................97
Description .......................................................... ....97
Component Function Check ..................................97
Diagnosis Procedure ...............................................97
STEERING LOCK UNIT .....................................99
Diagnosis Procedure ........................................... ....99
A/T SHIFT SELECTOR (PARK POSITION
SWITCH) ...........................................................
101
Diagnosis Procedure ........................................... ..101
REMOTE KEYLESS ENTRY RECEIVER ........103
Description .......................................................... ..103
Component Function Check ................................103
Diagnosis Procedure .............................................103
INTELLIGENT KEY BATTERY AND FUNC-
TION .................................................................
106
Description .......................................................... ..106
Component Function Check ................................106
Diagnosis Procedure .............................................106
HORN FUNCTION ............................................108
Description .......................................................... ..108
Component Function Check ................................108
Diagnosis Procedure ............................................108
COMBINATION METER DISPLAY FUNC-
TION .................................................................
110
Description .......................................................... ..110
Component Function Check ................................110
Diagnosis Procedure .............................................110
WARNING CHIME FUNCTION .......................111
Description ........................................................... ..111
Component Function Check ................................111
Diagnosis Procedure .............................................111
HAZARD FUNCTION ......................................112
Description .............................................................112
Component Function Check ................................112
Diagnosis Procedure .............................................112
KEY SWITCH (INTELLIGENT KEY UNIT IN-
PUT) ................................................................
113
Diagnosis Procedure .............................................113
KEY SWITCH (BCM INPUT) ...........................115
Diagnosis Procedure .............................................115
IGNITION KNOB SWITCH ..............................116
Ignition Knob Switch Check ...................................116
HEADLAMP FUNCTION .................................118
Diagnosis Procedure .............................................118
MAP LAMP AND IGNITION KEYHOLE ILLU-
MINATION FUNCTION ...................................
119
Diagnosis Procedure .............................................119
KEYFOB ID SET UP WITH CONSULT-III ......120
ID Code Entry Procedure ......................................120
KEYFOB ID SET UP WITHOUT CONSULT-III .121
ID Code Entry Procedure .................................... ..121
AUTOMATIC BACK DOOR SELF-DIAGNO-
SIS PROCEDURE ...........................................
123
Self-Diagnosis Procedure ......................................123
POWER LIFTGATE SWITCH FUNCTION ......125
Diagnosis Procedure ........................................... ..125
GLASS HATCH SWITCH ................................127
Diagnosis Procedure .............................................127
GLASS HATCH AJAR SWITCH .....................129
Diagnosis Procedure .............................................129
BACK DOOR CLOSE (CLOSE) SWITCH
SYSTEM ..........................................................
131
Diagnosis Procedure ........................................... ..131
BACK DOOR CLOSE (CANCEL) SWITCH
SYSTEM ..........................................................
132
Diagnosis Procedure ........................................... ..132
PINCH STRIP SYSTEM ..................................133
Diagnosis Procedure .............................................133
BACK DOOR WARNING CHIME SYSTEM ....134
Diagnosis Procedure .............................................134
HALF-LATCH SWITCH SYSTEM ...................135
Diagnosis Procedure .............................................135
Revision: December 20092009 QX56

DLK-4
BACK DOOR OPEN SWITCH SYSTEM .........136
Diagnosis Procedure ........................................... ..136
BACK DOOR CLOSE SWITCH SYSTEM .......137
Diagnosis Procedure ........................................... ..137
BACK DOOR SWITCH ....................................138
Diagnosis Procedure ........................................... ..138
CINCH LATCH MOTOR SYSTEM ...................139
Diagnosis Procedure ........................................... ..139
INTELLIGENT KEY UNIT POWER BACK
DOOR INPUT SIGNAL ....................................
140
Description ........................................................... ..140
Diagnosis Procedure .............................................140
INTELLIGENT KEY UNIT POWER BACK
DOOR OUTPUT SIGNAL ................................
141
Description ........................................................... ..141
Diagnosis Procedure .............................................141
HOMELINK UNIVERSAL TRANSCEIVER ......142
Wiring Diagram .................................................... ..142
Description .............................................................143
Component Function Check ................................144
Diagnosis Procedure .............................................144
ECU DIAGNOSIS ..................................... ..146
BCM (BODY CONTROL MODULE) ............... .146
Reference Value .................................................. ..146
Terminal Layout .....................................................148
Physical Values .....................................................148
Wiring Diagram — POWER DOOR LOCK SYS-
TEM — ..................................................................
154
Fail Safe ................................................................168
DTC Inspection Priority Chart .............................169
DTC Index ........................................................... ..169
INTELLIGENT KEY UNIT ................................171
Reference Value - Intelligent Key Unit ................. ..171
Reference Value - Steering Lock Solenoid ............174
Wiring Diagram — INTELLIGENT KEY SYSTEM
— ......................................................................... ..
175
Fail Safe ................................................................192
BACK DOOR CONTROL UNIT .......................193
Reference Value .................................................. ..193
Wiring Diagram—AUTOMATIC BACK DOOR
SYSTEM— ............................................................
195
Fail Safe .............................................................. ..205
SYMPTOM DIAGNOSIS ............................206
INTELLIGENT KEY SYSTEM SYMPTOMS ... .206
Symptom Table ................................................... ..206
DOOR LOCK FUNCTION SYMPTOMS ..........207
DOOR LOCK AND UNLOCK SWITCH ................. ..207
DOOR LOCK AND UNLOCK SWITCH : Symptom
Table .....................................................................
207
INTELLIGENT KEY ................................................ .208
INTELLIGENT KEY : Symptom Table ..................208
BACK DOOR OPENER FUNCTION ................210
BACK DOOR OPENER SWITCH .......................... .210
BACK DOOR OPENER SWITCH : Symptom Ta-
ble ........................................................................ .
210
BACK DOOR HANDLE .......................................... .210
BACK DOOR HANDLE : Symptom Table .............211
INTELLIGENT KEY ................................................ .211
INTELLIGENT KEY : Symptom Table ..................211
WARNING FUNCTION SYMPTOMS ...............212
Symptom Table .................................................... .212
KEY REMINDER FUNCTION SYMPTOMS .....215
Symptom Table .................................................... .215
HAZARD FUNCTION ..................................... ..216
Symptom Table .................................................... .216
HORN FUNCTION ............................................217
Symptom Table .................................................... .217
HOMELINK UNIVERSAL TRANSCEIVER ......218
Symptom Table .................................................... .218
SQUEAK AND RATTLE TROUBLE DIAG-
NOSES ..............................................................
219
Work Flow ............................................................ .219
Inspection Procedure ............................................221
Diagnostic Worksheet ...........................................223
PRECAUTION ...........................................225
PRECAUTIONS .............................................. ..225
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .............................................................. .
225
Precaution Necessary for Steering Wheel Rota-
tion After Battery Disconnect ................................
225
Precaution for work ...............................................226
PREPARATION .........................................227
PREPARATION .............................................. ..227
Special Service Tool ............................................ .227
Commercial Service Tool ......................................228
ON-VEHICLE REPAIR ..............................229
HOOD ............................................................. ..229
Fitting Adjustment ................................................ .229
Removal and Installation of Hood Assembly ........230
Removal and Installation of Hood Lock Control ....231
Hood Lock Control Inspection ...............................232
Hood Stay Disposal ............................................. .232
Revision: December 20092009 QX56

DLK-5
C
DE
F
G H
I
J
L
M A
B
DLK
N
O P
DOOR ............................................................. ..234
Fitting Adjustment ............................................... ..234
Removal and Installation .......................................235
Back Door Stay Disposal .................................... ..237
FRONT DOOR LOCK .......................................238
Component Structure .......................................... ..238
Removal and Installation .......................................238
Disassembly and Assembly ................................ ..240
REAR DOOR LOCK ........................................242
Component Structure .......................................... ..242
Removal and Installation .......................................242
BACK DOOR LOCK .......................................243
Power Back Door Opener .................................... ..243
Door Lock Assembly ..............................................244
Revision: December 20092009 QX56

DLK-6
< BASIC INSPECTION >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work FlowINFOID:0000000003775672
OVERALL SEQUENCE
DETAILED FLOW
JMKIA2270GB
Revision: December 20092009 QX56

DIAGNOSIS AND REPAIR WORKFLOWDLK-7
< BASIC INSPECTION > [WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G H
I
J
L
M A
B
DLK
N
O P
1.GET INFORMATION FOR SYMPTOM
Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred).
>> GO TO 2.
2.CHECK DTC
1. Check DTC.
2. Perform the following procedure if DTC is displayed.
- Record DTC and freeze frame data (Print them out with CONSULT-III.)
- Erase DTC.
- Study the relationship between the cause detected by DTC and the symptom described by the customer.
3. Check related service bulletins for information.
Is any symptom described and any DTC detected?
Symptom is described, DTC is displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4.
Symptom is not described, DTC is displayed>>GO TO 5.
3.CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONI TOR” mode and check real time diagnosis results.
Verify relation between the symptom and t he condition when the symptom is detected.
>> GO TO 5.
4.CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONI TOR” mode and check real time diagnosis results.
Verify relation between the symptom and t he condition when the symptom is detected.
>> GO TO 6.
5.PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC Confirmation Procedure for the display ed DTC, and then check that DTC is detected again.
At this time, always connect CONSULT-III to the vehicle, and check diagnostic results in real time.
If two or more DTCs are detected, refer to DLK-169, "
DTCInspectionPriorityChart" and determine trouble
diagnosis order.
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Component Function Check if DTC Confirmation Procedure is not included in Service Manual. This
simplified check procedure is an effective alternat ive though DTC cannot be detected during this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC Confirma-
tion Procedure.
Is DTC detected?
Yes >> GO TO 7.
No >> Refer to GI-38, "
Intermittent Incident".
6.DETECT MALFUNCTIONING SYST EM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to SYMPTO M DIAGNOSIS based on the confirmed symptom in step
4, and determine the trouble diagnosis order based on possible causes and symptom.
>> GO TO 7.
7.DETECT MALFUNCTIONING PA RT BY DIAGNOSTIC PROCEDURE
Inspect according to Diagnostic Procedure of the system.
NOTE:
Revision: December 20092009 QX56

DLK-8
< BASIC INSPECTION >[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS AND REPAIR WORKFLOW
The Diagnostic Procedure described based on open circuit inspection. A short circuit inspection is also
required for the circuit check in the Diagnostic Procedure.
Is malfunctioning part detected?
Ye s > > G O T O 8 .
No >> Check voltage of related BCM terminals using CONSULT-III.
8.REPAIR OR REPLACE THE MALFUNCTIONING PART
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace- ment.
3. Check DTC. If DTC is displayed, erase it.
>> GO TO 9.
9.FINAL CHECK
When DTC was detected in step 2, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunction have been repaired securely.
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Does the symptom reappear?
YES (DTC is detected)>>GO TO 7.
YES (Symptom remains)>>GO TO 6.
NO >> Inspection end
Revision: December 20092009 QX56