Cooling INFINITI QX56 2011 Factory Owner's Guide

EC-70
< SYSTEM DESCRIPTION >[VK56VD]
DIAGNOSIS SYSTEM (ECM)
*: The item is indicated, but not used.
NOTE:
Any monitored item that does not match the vehicle being diagnosed is deleted from the display automatically.
ACTIVE TEST MODE
Test Item
ECM TEMP 1
°C or °F  Displays a temperature calculated from a signal of
ECM temperature sensor 1.
ECM TEMP 2 °C or °F  Displays a temperature calculated from a signal of
ECM temperature sensor 2.
FUEL PUMP DUTY %  The control condition of the fuel pump control mod-
ule (FPCM) (determined by ECM according to the
input signals) is indicated.
Monitored item Unit Description Remarks
TEST ITEM CONDITION JUDGMENT CHECK ITEM (REMEDY)
VENT CON-
TROL/V  Ignition switch: ON (Engine
stopped)
 Turn solenoid valve ON and OFF with the CONSULT-III and listen
to operating sound. Solenoid valve makes an operating
sound.
 Harness and connectors
 Solenoid valve
ENG COOLANT
TEMP  Engine: Return to the original
non-standard condition
 Change the engine coolant tem- perature using CONSULT-III. If malfunctioning symptom disap-
pears, see CHECK ITEM.  Harness and connectors
 Engine coolant temperature sen-
sor
 Fuel injector
FUEL INJEC-
TION  Engine: Return to the original
non-standard condition
 Change the amount of fuel injec- tion using CONSULT-III. If malfunctioning symptom disap-
pears, see CHECK ITEM.
 Harness and connectors
 Fuel injector
 Air fuel ratio (A/F) sensor 1
FUEL/T TEMP
SEN  Change the fuel tank temperature using CONSULT-III.
PURG VOL
CONT/V  Engine: After warming up, run en-
gine at 1,500 rpm.
 Change the EVAP canister purge
volume control solenoid valve
opening percent using CON-
SULT-III. Engine speed changes according to
the opening percent.
 Harness and connectors
 Solenoid valve
FAN DUTY CON-
TROL* Ignition switch: ON
 Change duty ratio using CON-
SULT-III. Cooling fan speed changes.  Harness and connectors
 Cooling fan motor
 Cooling fan relay
 Cooling fan control module
 IPDM E/R
ALTERNATOR
DUTY Engine: Idle
 Change duty ratio using CON-
SULT-III. Battery voltage changes.  Harness and connectors
 IPDM E/R
Alternator
POWER BAL-
ANCE  Engine: After warming up, idle the
engine.
 A/C switch OFF
 Selector lever: P or N
 Cut off each injector signal one at a time using CONSULT-III. Engine runs rough or stops.
 Harness and connectors
 Compression
 Fuel injector
 Power transistor
Spark plug
 Ignition coil
IGNITION TIM-
ING  Engine: Return to the original
non-standard condition
 Timing light: Set
 Retard the ignition timing using
CONSULT-III. If malfunctioning symptom disap-
pears, see CHECK ITEM.
 Perform Idle Air Volume Learning.
Revision: 2010 May2011 QX56

DIAGNOSIS SYSTEM (ECM)EC-71
< SYSTEM DESCRIPTION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
*: Leaving cooling fan OFF with CONSULT-III while engine is running may cause the engine to overheat.
DTC & SRT CONFIRMATION MODE
SRT STATUS Mode
For items whose SRT codes are set, “CMPLT” is disp
layed on the CONSULT-III screen; for items whose SRT
codes are not set, “INCMP” is displayed.
SRT WORK SUPPORT Mode
This mode enables a technician to drive a vehicle to set the SRT while monitoring the SRT status.
DTC WORK SUPPORT Mode
*: DTC P1456 does not apply but appears in DTC Work Support Mode screens. V/T ASSIGN AN-
GLE
 Engine: Return to the original
non-standard condition
 Change intake valve timing using CONSULT-III. If malfunctioning symptom disap-
pears, see CHECK ITEM.
 Harness and connectors
 Intake valve timing control sole-
noid valve
FPCM  Engine: Return to the original
trouble condition
 Select “LOW”, “MID” and “HI” with CONSULT-III. Fuel pump speed changes or stops.
 Harness and connectors
 Fuel pump control module (FPCM)
TEST ITEM CONDITION JUDGMENT CHECK ITEM (REMEDY)
Test mode Test item Corresponding DTC No. Reference page
HO2S2 HO2S2 (B1) P1146 P0138
EC-249
HO2S2 (B1) P1147 P0137EC-243
HO2S2 (B1) P0139 P0139EC-257
HO2S2 (B2) P1166 P0158EC-249
HO2S2 (B2) P1167 P0157EC-243
HO2S2 (B2) P0159 P0159EC-257
A/F SEN1A/F SEN1 (B1) P1278/P1279 P0133
EC-238A/F SEN1 (B1) P1276 P0130EC-228
A/F SEN1 (B2) P1288/P1289 P0153EC-238
A/F SEN1 (B2) P1286 P0150EC-228
EVAPORATIVE SYSTEMEVP V/S LEAK P0456/P1456* P0456
EC-346, "
DTC Logic"
PURG VOL CN/V P1444 P0443EC-317, "DTC Logic"
PURG FLOW P0441 P0441EC-312, "DTC Logic"
Revision: 2010 May2011 QX56

EC-76
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
EVAP DIAG READY  Ignition switch: ON Indicates the ready condi-
tion of EVAP leak diagnosis.
VVEL LEARN  Ignition switch: OFF
→ ON
(After warming up) VVEL learning has no
t been performed
yet. YET
VVEL learning has already been per-
formed successfully. DONE
VVEL SEN LEARN-B1  VVEL learning has already been performed successfully Approx. 0.30 - 0.80 V
VVEL SEN LEARN-B2  VVEL learning has already been performed successfully Approx. 0.30 - 0.80 V
VVEL POSITION SEN-
B1  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 0.25 - 1.50 V
When revving engine up to 2,000 rpm
quickly
Approx. 0.25 - 4.75 V
VVEL POSITION SEN-
B2  Engine: After warming up
 Selector lever: P or N position
 Air conditioner switch: OFF
No load Idle Approx. 0.25 - 1.50 V
When revving engine up to 2,000 rpm
quickly
Approx. 0.25 - 4.75 V
VVEL TIM-B1  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 0 - 23 deg
When revving engine up to 2,000 rpm
quickly
Approx. 0 - 90 deg
VVEL TIM-B2  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 0 - 23 deg
When revving engine up to 2,000 rpm
quickly
Approx. 0 - 90 deg
FPCM  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load  Engine: Cranking HI
 Revving engine from idle to 4,000 rpm
quickly MID
 Engine: Idle
 Engine coolant temperature: More than 10 °C (50 °F) LOW
BAT TEMP SEN  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle
Indicates the temperature
around the battery.
COOLING FAN SPD  Engine speed: Idle
 Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Water temp: Less than 98
°C Approx. 100 – 200 rpm
Water temp: More than 98 °C Approx. 600 – 700 rpm
THRTL STK CNT B1 NOTE:
The item is indicated, but not used. —
HO2 S2 DIAG2(B1) NOTE:
The item is indicated, but not used.
—
HO2 S2 DIAG2(B2) NOTE:
The item is indicated, but not used. —
FUEL INJ TIMG Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 16 deg
2,000 rpm Approx.
−170 deg
H/P FUEL PUMP DEG  Engine: After warming up
 Selector lever: P or N position
 A/C switch: OFF
No load Idle Approx. 211.0 deg
2,000 rpm Approx. 206.0 deg
Monitor Item Condition Values/Status
Revision: 2010 May2011 QX56

ECM
EC-81
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
23
(V) 45
(L/O) Low fuel pressure sensor Input [Engine is running]
 Warm-up condition
 Idle speed
2.4 - 3.6 V
[Engine is running]
 Warm-up condition
 Engine speed: 2,000 rpm 2.4 - 3.6 V
25
(LG) —Sensor ground
[Mass air flow sensor/ Intake air
temperature sensor] —— —
27
(P) 45
(L/O) Sensor power supply
(Power steering pressure sen-
sor/ Low fuel pressure sensor/
Electrically-controlled cooling
fan coupling)
— [Ignition switch: ON] 5 V
28
(SB) 40
(W/L) Sensor power supply
(Fuel rail pressure sensor/En-
gine oil pressure sensor)
— [Ignition switch: ON] 5 V
29
(W) 35
(—) Knock sensor (bank 1) Input [Engine is running]
 Idle speed
2.0 V*
1
31
(V/W) 40
(W/L) Fuel rail pressure sensor Input [Engine is running]
 Warm-up condition
 Idle speed
0.98 - 1.2 V
[Engine is running]
 Warm-up condition
 Revving engine from idle to 4,000 rpm quickly 1.1 - 2.9 V
32
(R) 40
(W/L) Engine coolant temperature
sensor
Input [Engine is running] 0 - 4.8 V
Output voltage varies with engine
coolant temperature.
33
(W) 35
(—) Knock sensor (bank 2) Input [Engine is running]
 Idle speed
2.0 V*
1
35
(—) —Sensor ground
(Knock sensor)
—— —
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
JPBIA3357ZZ
JPBIA3358ZZ
Revision: 2010 May2011 QX56

EC-82
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
37
(V) 175
(B) Cooling fan speed Input [Ignition switch: ON]
 Engine stopped
5 V
[Engine is running]
 Idle speed
 After warm-up condition BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
 Idle speed
 Before warm-up condition BATTERY VOLTAGE
(11 - 14 V)
39
(P/B) 45
(L/O) Power steering pressure sensor Input [Engine is running]
 Steering wheel: Being turned
0.5 - 4.5 V
[Engine is running]
 Steering wheel: Not being turned 0.4 - 0.8 V
40
(W/L) —Sensor ground
(Fuel rail pressure sensor/En-
gine coolant temperature sen-
sor/Engine oil temperature
sensor) —— —
42
(L/Y) 40
(W/L) Engine oil temperature sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with engine
oil temperature.
45
(L/O) —Sensor ground
(Power steering pressure sen-
sor/ Low fuel pressure sensor/
Electrically-controlled cooling
fan coupling) —— —
46
(SB) 175
(B) Fuel injector driver power supply Input [Ignition switch: ON]
BATTERY VOLTAGE
(11 - 14 V)
[Ignition switch: OFF] 1.5 V
47
(G) 175
(B) Heated oxygen sensor 2 heater
(bank 1)
Input[Engine is running]
 Engine speed: Below 3,600 rpm af-
ter the following conditions are met
- Engine: after warming up
- Keeping the engine speed between 3,500 and 4,000 rpm for 1 minute
and at idle for 1 minute under no
load 10 V
[Ignition switch: ON]
 Engine: Stopped
[Engine is running]
 Engine speed: Above 3,600 rpm BATTERY VOLTAGE
(11 - 14 V)
Te r m i n a l N o .
(Wire color) Description
ConditionVa l u e
(Approx.)
+ – Signal name Input/
Output
JPBIA3332ZZ
JPBIA3733ZZ
JMBIA0037GB
Revision: 2010 May2011 QX56

EC-94
< ECU DIAGNOSIS INFORMATION >[VK56VD]
ECM
DTC No. Detected items Engine operating condition in fail-safe mode
U0113
U1003
U1024 Can communication circuit VVEL actuator
motor relay is turned off, and VVEL value is become at a minimum angle.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
P0011
P0021 Intake valve timing control The signal is not energized to the intake valve timing control solenoid valve and the valve
control does not function.
P0087 FRP control system  Engine torque is limited.
 VVEL value is maintained at a fixed angle.
P0088 Engine speed is limited.
P008A Low fuel pressure control
system Engine torque is limited.
P0090 FRP control system  Engine torque is limited.
 VVEL value is maintained at a fixed angle.
P0102
P0103 Mass air flow sensor circuit Engine speed will not rise more than 2,400 rpm due to the fuel cut.
P0117
P0118 Engine coolant tempera-
ture sensor circuit
Engine coolant temperature will be determined by ECM based on the following condition.
CONSULT-III displays the engine coolant temperature decided by ECM.
Condition Engine coolant temperature decided
(CONSULT-III display)
Just as ignition switch is turned ON
or START 40
°C (104 °F)
Approx. 4 minutes or more after
engine starting 80
°C (176 °F)
Except as shown above 40 - 80 °C (104 - 176 °F)
(Depends on the time)
When the fail-safe system for engine coolant temperature sensor is activated, the cooling
fan operates while engine is running.
P0122
P0123
P0222
P0223
P2135 Throttle position sensor The ECM controls the electric throttle control actuator in regulating the throttle opening in
order for the idle position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal
condition.
Therefore, the acceleration will be poor.
P0190 FRP sensor  Engine speed is limited.
 High pressure fuel pump is activated at maximum discharge pressure.
P0201
P0202
P0203
P0204
P0205
P0206
P0207
P0208 Injector  Engine torque is limited.
 Fuel injection shut-off of malfunction cylinder.
 Mixture ratio feedback control does not function.
 Idle engine speed is increased.
P0500 Vehicle speed sensor The cooling fan operates (Highest) while engine is running.
P0524 Engine oil pressure The signal is not energized to the intake valve timing control solenoid valve and the valve
control does not function.
Engine speed will not rise more than 2,400 rpm due to the fuel cut.
P0605 ECM (When ECM calculation function is malfunctioning:)
ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
ECM deactivates ASCD operation.
P0607 ECM VVEL actuator motor relay is
turned off, and VVEL value is become at a minimum angle.
Engine speed will not rise more than 3,500 rpm due to the fuel cut.
Revision: 2010 May2011 QX56

ECM
EC-97
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
Priority Detected items (DTC)
1  U0101 CAN communication line  U0113 U1003 CAN communication line
 U1001 CAN communication line
 U1024 VVEL CAN communication line
 P006A P0101 P0102 P0103 Mass air flow sensor
 P010A Manifold absolute pressure sensor
 P0112 P0113 P0127 Intake air temperature sensor
 P0116 P0117 P0118 P0125 Engine coolant temperature sensor
 P0122 P0123 P0222 P0223 P1225 P1226 P2135 Throttle position sensor
 P0128 Thermostat function
 P0181 P0182 P0183 Fuel tank temperature sensor
 P0196 P0197 P0198 Engine oil temperature sensor
 P0327 P0328 P0332 P0333 Knock sensor
 P0335 Crankshaft position sensor
 P0340 P0345 Camshaft position sensor
 P0460 P0461 P0462 P0463 Fuel level sensor
 P0500 Vehicle speed sensor
 P0527 Cooling fan speed sensor
 P0605 P0607 P0611 P062B ECM
 P0643 Sensor power supply
 P0700 TCM
 P0705 P0850 Transmission range switch
 P1089 P1092 P1608 VVEL control shaft position sensor
 P1197 Out of gas*
 P1220 Fuel pump control module (FPCM)
 P1421 P1423 P1424 Cold start control
 P1550 P1551 P1552 P1553 P1554 Battery current sensor
 P1556 P1557 Battery temperature sensor
 P1606 P1607 VVEL control module
 P1610 - P1615 NATS
 P2122 P2123 P2127 P2128 P2138 Accelerator pedal position sensor
 P2539 P2541 P2542 Low fuel pressure sensor
Revision: 2010 May2011 QX56

ECM
EC-101
< ECU DIAGNOSIS INFORMATION > [VK56VD]
C
D
E
F
G H
I
J
K L
M A
EC
NP
OP0327 0327 KNOCK SEN/CIRC-B1 — 2 —
EC-297
P0328 0328 KNOCK SEN/CIRC-B1 — 2 —
P0332 0332 KNOCK SEN/CIRC-B2 — 2 —
P0333 0333 KNOCK SEN/CIRC-B2 — 2 —
P0335 0335 CKP SEN/CIRCUIT — 2×EC-299
P0340 0340 CMP SEN/CIRC-B1 — 2 ×
EC-303
P0345 0345 CMP SEN/CIRC-B2 — 2 ×
P0420 0420 TW CATALYST SYS-B1 ×2 ×
EC-307
P0430 0430 TW CATALYST SYS-B2 ×2 ×
P0441 0441 EVAP PURG FLOW/MON ×2 ×EC-312
P0443 0443 PURG VOLUME CONT/V — 2 ×EC-317
P0444 0444 PURG VOLUME CONT/V — 2 ×
EC-322
P0445 0445 PURG VOLUME CONT/V — 2 ×
P0447 0447 VENT CONTROL VALVE — 2 ×EC-325
P0448 0448 VENT CONTROL VALVE — 2 ×EC-329
P0451 0451 EVAP SYS PRES SEN — 2 ×EC-333
P0452 0452 EVAP SYS PRES SEN — 2 ×EC-336
P0453 0453 EVAP SYS PRES SEN — 2 ×EC-341
P0456 0456 EVAP VERY SML LEAK
×*82 ×EC-346
P0460 0460 FUEL LEV SEN SLOSH — 2 ×EC-352
P0461 0461 FUEL LEVEL SENSOR — 2 ×EC-353
P0462 0462 FUEL LEVL SEN/CIRC — 2 ×EC-355
P0463 0463 FUEL LEVL SEN/CIRC — 2 ×EC-355
P0500 0500
VEH SPEED SEN/CIRC*5—2 ×EC-356
P0506 0506 ISC SYSTEM — 2 ×EC-358
P0507 0507 ISC SYSTEM — 2 ×EC-360
P050E 050E COLD START CONTROL — 2 ×EC-362
P0524 0524 ENGINE OIL PRESSURE — 2 ×EC-364
P0527 0527 COOLING FAN SPD SEN — 2 — EC-367
P0550 0550 PW ST P SEN/CIRC — 2 —EC-371
P0603 0603 ECM BACK UP/CIRCUIT — 2×EC-374
P0605 0605 ECM — 1 or 2 × or — EC-376
P0607 0607 ECM — 1 ×EC-378
P0611 0611 FIC MODULE — 2 ×EC-379
P062B 062B ECM — 2 × or — EC-380
P0643 0643 SENSOR POWER/CIRC — 1 ×EC-381
P0705 0705 T/M RANGE SENSOR A — 2 ×TM-106
P0710 0710
FLUID TEMP SENSOR*7—2 ×TM-107
P0717 0717 INPUT SPEED SENSOR A — 2 ×TM-109
P0720 0720
OUTPUT SPEED SENSOR*5—2 ×TM-110
P0729 0729
6GR INCORRECT RATIO*7—2 ×TM-114
P0730 0730 INCORRECT GR RATIO — 2 ×TM-116
DTC*1
Items
(CONSULT-III screen terms) SRT code Trip MIL Reference
page
CONSULT-III
GST*
2ECM*3
Revision: 2010 May2011 QX56

EC-160
< BASIC INSPECTION >[VK56VD]
HOW TO SET SRT CODE
6.PATTERN 2
1. Drive the vehicle. And depress the accelerator pedal until vehicle speed is 90 km/h (56 MPH), then
release the accelerator pedal and keep it released for more than 10 seconds.
2. Depress the accelerator pedal until vehicle speed is 90 km/h (56 MPH) again
NOTE:
 Checking the vehicle speed with GST is advised.
 When steady-state driving is performed again even afte r it is interrupted, each diagnosis can be conducted.
In this case, the time required for diagnosis may be extended.
>> GO TO 7.
7.PATTERN 3
 Operate vehicle following the driving pattern shown in the figure.
 Release the accelerator pedal during deceleration of vehicle speed from 90 km/h (56 MPH) to 0 km/h (0 MPH).
>> GO TO 8.
8.PATTERN 4
 The accelerator pedal must be held very steady during steady-state driving.
 If the accelerator pedal is moved, the test must be conducted again.
>> GO TO 9.
9.PATTERN 5
 Cool down the engine so that the engine coolant temperature lowers between 15 - 35 °C (59 - 95 °F).
CAUTION:
Never turn the ignition switch ON while cooling down the engine.
 Engine coolant temperature at engine start is between 15 – 35 °C (59 – 95 °F) and has lowered 45 °C (113 °F)
or more since the latest engine stop.
>> GO TO 10.
10.CHECK SRT STATUS
WITH CONSULT-III
Select “SRT STATUS” in “DTC & SRT CONFIRMATION” mode with CONSULT-III.
WITHOUT CONSULT-III
Perform “SRT status” mode with EC-60, "
On Board Diagnosis Function".
WITH GST
Select Service $01 with GST.
Is SRT(s) set?
YES >> END
NO >> Call TECH LINE or take appropriate action.
PBIB2244E
Revision: 2010 May2011 QX56

EC-276
< DTC/CIRCUIT DIAGNOSIS >[VK56VD]
P0190, P0192,
P0193 FRP SENSOR
P0190, P0192, P0193 FRP SENSOR
DTC LogicINFOID:0000000006288295
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start the engine ON and wait at least 60 seconds.
2. Check DTC or 1st trip DTC.
Is DTC or 1st trip DTC detected?
YES >> Proceed to EC-276, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000006288296
1.CHECK FRP SENSOR POWER SUPPLY-I
1. Turn ignition switch OFF.
2. Disconnect FRP sensor connector.
3. Turn ignition switch ON.
4. Check the voltage between FRP sensor harness connector terminals.
Inspection result normal?
YES >> GO TO 6.
NO >> GO TO 2.
2.CHECK FRP SENSOR POWER SUPPLY-II
Check the voltage between FRP sensor harness connector and the ground.
DTC No. Trouble diagnosis name DTC detecting condition Possible cause
P0190 Fuel rail pressure sensor
circuit low input and high in-
put Signal voltage from the fuel rail pressure
sensor remains at more than 4.84 V /
less than 0.2 V for 5 seconds or more.  Harness or connectors
(Fuel rail pressure sensor circuit is open or
shorted.)
(Power steering pressure sensor circuit is
open or shorted.)
(Low fuel pressure sensor circuit is open or
shorted.)
(The electrically-controlled cooling fan cou-
pling circuit is open or shorted)
 Fuel rail pressure sensor
 Power steering pressure sensor
 Low fuel pressure sensor
 Electrically-controlled cooling fan coupling
P0192
Fuel rail pressure sensor
circuit low input Signal voltage from the fuel rail pressure
sensor remains at less than 0.37 V for 5
seconds or more.
P0193 Fuel rail pressure sensor
circuit high input Signal voltage from the fuel rail pressure
sensor remains at more than 3.46 V for 5
seconds or more.
FRP sensor
Voltag e
(Approx.)
Connector +
−
terminal
F26 1 3 5 V
Revision: 2010 May2011 QX56