ISUZU TF SERIES 2004 Workshop Manual

ENGINE MECHANICAL 6A – 111
























4. Align the idler gear setting mark with the crankshaft
timing gear (1) setting mark.
5. Align the idler gear setting mark with the camshaft
timing gear (2) setting mark.
6. Install the thrust collar and bolts to the cylinder body
through the shaft.
The thrust collar oil hole must be facing up, and the
thrust collar chamfered must be outward.
7. Tighten the idler gear bolt to the specified torque.


Idler Gear "A" Bolt Torque N·m(kg·m/lbft)
30 (3.1/22)

020R300006











22. Idler Gear "B" and Shaft
1. Apply engine oil to the idler gear and the idler gear shaft.
2.
Align the idler gear "B" (3) setting mark with the idler
gear "A" (4) setting mark.
3. Tighten the idler gear bolt to the specified torque.
4. Be sure to remove the lock bolt (5) from idle gear “B”.


Idler Gear "B" Bolt Torque N·m(kg·m/lbft)
76 (7.7/56)




020L200019

5. If the idle gear "B" is disassembled, reassemble in the
following procedure.
1) Drive pins into the main gear, the front gear, and the
rear gear.





020L200007

2) Install the main gear bearing from the front side of
the main gear (the side with the groove).
3) Place the main gear in a vise with copper plate so
that the rear side of the main gear facing up.
020RY00036

6A – 112 ENGINE MECHANICAL




RTW31BSH000101

4) Set the spring as shown in the illustration.





RTW31BSH000201

5) Position the rear gear so that the pin is aligned with
the receiving end of the spring.




RTW31BSH000301

6) Install the snap ring to the main gear groove.






RTW31BSH000501

7) Install suitable bolts, nuts and washers to special tool
as shown in the illustration to rotate the scissors
gear.
End yoke holder: 5-8840-2447-0

ENGINE MECHANICAL 6A – 113




RTW31BSH000401

8) Insert the bolts of the special tool into the rear gear
setting hole. Rotate the rear gear to mesh the teeth
of main gear and rear gear.
9) Insert a lock bolt (M6  1 L=30) into scissors gea
r
fixing hole to prevent the scissors gear from turning.
10) Place the main gear in a vise with copper plate so
that the front side of the main gear facing up.
11) Repeat steps 4 to 8 to install the front gear.
12) Lock the front gear, the main gear, and the rear gea
r
with lock bolt (inserted at Step 8).

6A – 114 ENGINE MECHANICAL








23. Injection Pump
1. Install the O-ring (1) to the injection pump flange (2).
2. Attach the noise insulator rubber to the cylinder body .
3. Install the injection pump to the timing gear case.Align
the idler gear "B" (3) mark with the injection pump timing
gear (4) mark.












RTW36AMH000101



























4JA1TC/4JH1TC:
4. Tighten the injection pump bolts (5) to the specified
torque.

Injection Pump Bolt Torque N·m(kg·m/lbft)
19 (1.9/14)

5. Install the injection pump bracket (6) and the bracke
t
bolts (7) and (8) to the cylinder body.
Temporarily tighten the bracket bolts.
6. Tighten the bracket bolts (7) to the specified torque.
7. Tighten the bracket bolt (8) to the specified torque.
NOTE:
Tighten the bracket bolt (7) first.

Injection Pump Bracket Bolt Torque N·m(kg·m/lbft)
19 (1.9/14)




020RY00039

ENGINE MECHANICAL 6A – 115



RTW46ASH002201




















4JA1T(L):
4. Tighten the injection pump bolts to the specified torque.
5. Install the injection pump bracket (4) and the bracke
t
bolts (5) and (6) to the cylinder body. Temporarily tighten
the bracket bolts.
6. Tighten the bracket bolts (5) to the specified torque.
7. Tighten the bracket bolts (6) to the specified torque.


Injection pump Bracket Bolt Torque (6) N·m(kg·m/lbft)
19 (1.9/14)

Injection pump Bracket Bolt Torque (5) N·m(kg·m/lbft)
40 (4.1/30)



030RY00007














24. Water Pump
1. Apply the recommended liquid gasket or its equivalent
to the water pump at the position shown in the
illustration.
Do not apply an excessive amount of liquid gasket.
2. Tighten the water pump bolts to the specified torque.


Water Pump Bolt Torque N·m(kg·m/lbft)
20 (2.0/14)













25.Timing Gear Case Cover
1.
Align the gear case with the timing gear case knock pin
and then install the timing gear case cover.
2. Tighten the gear case cover bolts to the specified
torque.


Gear Case Cover Bolt Torque N·m(kg·m/lbft)
M8 19 (1.9/14)
M12 76 (7.7/56)

























26. Crankshaft Damper Pulley
Tighten the crankshaft damper pulley bolt to the specified
torque.
Note:
Hold the flywheel ring gear stationary to prevent the
crankshaft from turning when tightening the damper
pulley bolt.


Crankshaft Damper Pulley Bolt Torque N·m(kg·m/lbft)
206 (21/152)
Take care not to damage the crankshaft damper pulley
boss.


014R100014 020R300004

6A – 116 ENGINE MECHANICAL


27. Cylinder Head Gasket
The cylinder head gasket "TOP" mark must be facing up.

NOTE:
Before the gasket installation, measure the piston
head projection and select the appropriate head
gasket.
Refer to "INSPECTION AND REPAIR", "Cylinder Head
Gasket Selection".









28. Cylinder Head
1. Align the cylinder body dowels and the cylinder head
dowel holes.
Carefully place the cylinder head on the cylinder head
gasket.
2. Apply a coat of engine oil to the cylinder head bolt
threads and setting faces.















3. Tighten the cylinder head bolts in three steps of anglar
tightening methed.
Follow the numerical sequence shown in the
illustration.


Cylinder Head Bolt Torque N·m(kg·m/lbft)
1st step 49 (5.0/36)
2nd step
60
- 75

3rd step
60
- 75













30. Rocker Arm Shaft and Rocker Arm
Tighten the rocker arm shaft bracket bolts in the numerical
order shown in the illustration.


Rocker Arm Shaft Braket Bolt Torque N·m(kg·m/lbft)
54 (5.5/40)











31. Thermostat Housing
1. Install the thermostat housing.
2. Tighten the thermostat housing bolts to the specified
torque.


Thermostat Housing Bolt Torque N·m(kg·m/lbft)
19 (1.9/14)

014LX083 011LX073
031R300002

ENGINE MECHANICAL 6A – 117


RTW46ASH001201
33. Injection Nozzle Holder
1. Install the injection nozzle gasket and the O-ring to the
injection nozzle holder.
Be sure that the O-ring fits snugly in the injection
nozzle groove.
2. Install the nozzle holder toghther with the nozzle holder
bracket to the cylinder head.










3. Tighten the nozzle holder bracket bolt to the specified
torque.


Injection Nozzle Holder Bracket Bolt
Torque N·m(kg·m/lbft)
37 (3.8/28)













Note on Valve Clearance Adjustment
Valve clearances must be adjusted before the cylinder
head cover is reinstalled.Refer to "Valve Clearance
Adjustment" in the "Servicing" Section of this manual.


Valve Clearance (At Cold) mm(in)
0.4 (0.0157)


RTW46ASH001101















34. Cylinder Head Cover
1. Apply engine oil to the rocker arm and the valve spring.
2. Install the cylinder head cover gasket to the head
cover. Check to see that the head cover gasket has no
loose areas.
3. Tighten the cylinder head cover nuts in the numerical
order shown in the illustration.


Cylinder Head Cover Bolt Torque N·m(kg·m/lbft)
13 (1.3/9.4)
4. Connect the positive crankcase ventilation (PCV) hose
to the cylinder head cover.




014RY00015

6A – 118 ENGINE MECHANICAL

INSTALLATION
EXTERNAL PARTS





RTW36AMF000701
Installation Steps
1.
Exhaust Manifold 18. Engine Mounting Bracket and
2.
Oil Cooler with Oil Filter Foot
3. Generator Bracket 19. Intake Manifold
4. Water Inlet Pipe 20. Power Steering Oil Pump
5.
Generator and Adjusting Plate Bracket
6.
Vacuum Pump Oil Return Hose 21. Fuel Injection Pipe with Clip
7.
Compressor Bracket 22. Fuel Filter Bracket (Except
EURO III)
8. Turbocharger 23. Fuel Filter Assembly (Except
EURO III)
9. Catalytic Converter 24. Oil Level Gauge
10. Heat Protector 25. EGR Valve
11. Cooling Fan Pulley 26-1. EGR Pipe
12. Oil Cooler Water Pipe 26-2. EGR Cooler (EURO III model
only)
13. Fuel Leak Off Pipe 27. Intake Pipe and Throttle Body
(4JA1TC/4JH1TC only)
14. Oil Pressure Warning Switch 28. Clutch Assembly or Flex Plate
15. Starter Motor
16. Injection Pump
17. Injection Pump Cover

ENGINE MECHANICAL 6A – 119












Installation
1. Exhaust Manifold
1) Install the exhaust manifold to the cylinder head with
the manifold gasket.
2) Tighten the exhaust manifold bolts and nuts to the
specified torque a little at a time.
Exhaust Manifold Bolt and Nuts
Torque N·m(kg·m/Ib ft)
27 (2.7/20)




3) Install the exhaust manifold bracket to the manifold
and the cylinder body.
Manifold Bracket Bolt Torque N·m(kg·m/Ib ft)
19 (1.9/14)






RTW46ASH001301









2. Oil Cooler with Oil Filter
1) Install the O-ring to the oil filter body flange groove.
2) Install the oil filter body to cylinder block and tighten to
the specified torque.
Oil Filter Body Bolt and Nut
Torque N·m(kg·m/Ib ft)
BOLT 19 (1.9/14)
NUT 24 (2.4/17)









3. Generator Bracket
Install the generator bracket to the cylinder body and
tighten the bracket bolts to the specified torque.
Bracket Bolt Torque N·m(kg·m/Ib ft)
40 (4.1/30)




027R100003
027R100004
066RY00001

6A – 120 ENGINE MECHANICAL









4. Water Inlet Pipe
1) Tighten the water inlet pipe bolts to the specified
torque.
Suction Pipe Bolt Torque N·m(kg·m/Ib ft)
19 (1.9/14)





5. Generator and Adjusting Plate
1) Install the generator to the bracket (1).
2) Temporarily tighten the generator bolt (2) and
adjusting plate bolts (3).
The bolts will be finally tightened after installation of
the cooling fan drive belt.



3) Connect the vacuum pump rubber hose (4) to the
vacuum pump (5), and the oil pan (6).
6. Vacuum Pump Oil Return Hose
Connect the vacuum oil pipe (7) to the vacuum pump, and
the cylinder body

052R300001
7. Compressor Bracket
1) Install the compressor bracket to the cylinder head.
2) Tighten the bracket bolts to the specified torque.
Bracket Bolt Torque N·m(kg·m/Ib ft)
M8
1.25
19 (1.9/14)
M10
1.25
40 (4.1/30)











066RY00002 032R300001
042RY00003