power ISUZU TF SERIES 2004 Manual Online
[x] Cancel search | Manufacturer: ISUZU, Model Year: 2004, Model line: TF SERIES, Model: ISUZU TF SERIES 2004Pages: 4264, PDF Size: 72.63 MB
Page 980 of 4264
8A-322 ELECTRICAL-BODY AND CHASSIS
DRIVER SEAT SIDE POWER WINDOW
MOTOR
Removal
1. Window Regulator ASM
Refer to the removal steps of the WINDOW
REGULATOR/POWER WINDOW MOTOR in Section
10 “BODY”.
2. Power Window Motor
Loosen the fixing bolts to remove the power windo
w
motor from the regulator.
Installation
To install, follow the removal steps in the reverse order.
FRONT PASSENGER’S POWER WINDOW
MOTOR
Removal
1. Window Regulator ASM
Refer to the removal steps of the WINDOW
REGULATOR/POWER WINDOW MOTOR in Section
10 “BODY”.
2. Power Window Motor
Loosen the fixing bolts to remove the power windo
w
motor from the regulator.
Installation
To install, follow the removal steps in the reverse order.
REAR POWER WINDOW MOTOR-LH &
RH
Removal and Installation
Refer to the “DRIVER SEAT SIDE POWER WINDOW
MOTOR” removal and installation steps in this section.
Page 981 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-323
INSPECTION AND REPAIR
B-8
Power Window Relay
Check continuity between the relay terminals.
2- 1......................... No continuity
(When battery voltage is applied between
3 and 4)
2- 1......................... Continuity
Harness side
D-20 D-5
Driver Seat Side Power Window & Door Lock
Switch
1. Harness Side Connector Circuit
Disconnect the switch connector, and check voltage and
continuity between the harness side connector terminals as
shown in the following table.
Terminal
No. Wire
color Connecting to Check item Connectin
g terminal Check condition Standard
6 G/R Power window
relay Voltage 6-Ground Starter SW “ON” Approx.
12V
7 BR/R
Power window
8 BR/W motor
3 B Ground Continuity 3-Ground - Continuity
Harness side
D-10
Front Passenger’s Power Window & Door Lock
Switch
1. Harness Side Connector Circuit
Disconnect the switch connector, and check voltage and
continuity between the harness side connector terminals as
shown in the following table.
Continuity
- 7-8 Continuity
Page 982 of 4264
8A-324 ELECTRICAL-BODY AND CHASSIS
Terminal
No. Wire
color Connecting to Check item Connectin
g terminal Check condition Standard
11 G/R Power window
relay Voltage 11-Ground Starter SW “ON” Approx.
12V
12 BR/R
Power window
10 BR/W motor
5 B Ground Continuity 5-Ground - Continuity
Harness side
D-12 D-16
Rear Power Window Switch-LH & RH
1. Harness Side Connector Circuit
Disconnect the switch connector, and check voltage and
continuity between the harness side connector terminals as
shown in the following tables.
D-12 (RR-LH)
Terminal
No. Wire
color Connecting to Check item Connectin
g terminal Check condition Standard
6 G/R Power window
relay Voltage 6-Ground Starter SW “ON” Approx.
12V
8 BR/R
Power window
7 BR/W motor
3 B Ground Continuity 3-Ground - Continuity
D-16 (RR-RH)
Terminal
No. Wire
color Connecting to Check item Connectin
g terminal Check condition Standard
6 G/R Power window
relay Voltage 6-Ground Starter SW “ON” Approx.
12V
8 BR/R
Power window
7 BR/W motor
3 B
4 B
Continuity - 12-10 Continuity
Continuity Continuity 8-7
-
Continuity Continuity 8-7
-
Ground Continuity
3-1
Continuity -
Page 983 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-325
Harness side
D-5
Driver Seat Side Power Window Motor
1. Driver Seat Side Power Window & Door Lock Switch
Connector Circuit
Disconnect the switch connector, apply the battery voltage
(12V) to the harness side connector terminals and check
operation.
Connecting terminals
Operation
7 (BR/R) 8 (BR/W) direction
- + DOWN
+ - UP
2. Driver Seat Side Power Window Motor Connector
Circuit
Disconnect the switch connector, apply the battery voltage
(12V) to the motor side connector terminals and check
operation.
Connecting terminals
Operation
1 2 direction
+ - DOWN
- + UP
Page 984 of 4264
8A-326 ELECTRICAL-BODY AND CHASSIS
Harness side
D-10
Front Passenger’s Power Window Motor
1. Front Passenger’s Power Window Switch & Door Lock
Switch Connector Circuit
Disconnect the motor connector, apply the battery voltage
(12V) to the harness side connector terminals and check
operation.
Connecting terminals
Operation
12 (BR/R) 10 (BR/W) direction
- + DOWN
+ - UP
2. Front Passenger’s Power Window Motor Connector
Circuit
Disconnect the switch connector, apply the battery voltage
(12V) to the motor side connector terminals and check
operation.
Connecting terminals
Operation
1 2 direction
+ - DOWN
- + UP
Page 985 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-327
Harness side
D-12
Rear Passenger’s Power Window Motor-LH
1. Rear Power Window Switch-LH Connector Circuit
Disconnect the motor connector, apply the battery voltage
(12V) to the harness side connector terminals and check
operation.
Connecting terminals
Operation
8 (BR/R) 7 (BR/W) direction
- + DOWN
+ - UP
2. Rear Power Window Motor-LH Connector Circuit
Disconnect the switch connector, apply the battery voltage
(12V) to the motor side connector terminals and check
operation.
Connecting terminals
Operation
1 2 direction
+ - DOWN
- + UP
Page 986 of 4264
8A-328 ELECTRICAL-BODY AND CHASSIS
Harness side
D-16
Rear Power Window Motor-RH
1. Rear Power Window Switch-RH Connector Circuit
Disconnect the motor connector, apply the battery voltage
(12V) to the harness side connector terminals and check
operation.
Connecting terminals
Operation
8 (BR/R) 7 (BR/W) direction
- + DOWN
+ - UP
2. Rear Power Window Motor-RH Connector Circuit
Disconnect the switch connector, apply the battery voltage
(12V) to the motor side connector terminals and check
operation.
Connecting terminals
Operation
1 2 direction
+ - DOWN
- + UP
Page 993 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-335
TROUBLESHOOTING
CIGARETTE LIGHTER
1. Lighter does not pop out after being pushed in. It does not become hot.
Checkpoint Trouble Cause Countermeasure
Reinstall or replace the fuse
No. C-12 (15A)
Poor Fuse No. C-12 (15A,
Fuse box) contact or blown
NG
Replace the lighter
Lighter continuity between
center part and outer area
Open circuit or poor connector
contact
Repair open circuit or
connector contact
Voltage between connector 1
B-21 and the ground at
starter SW. is ACC position
(Should be battery voltage
present)
Open circuit or poor connector
contact
NG NG OK
OK OK
Audio system (System should
receive power)
Repair open circuit or
connector contact
Open circuit or poor connector
contact
NG
Continuity between connector
1
B-22 and the ground
2. Lighter pops out prematurely before becoming hot
Repair or replace the lighter
and/or casingDeformed lighter or casing NGLighter and casing
3. Lighter becomes too hot
Repair or replace the lighter
and/or casingDeformed lighter and casing NGLighter and casing
Page 995 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-337
POWER DOOR MIRROR
PARTS LOCATION (RHD)
RTW48AXF020401 & RTW48AXF020501
Page 1003 of 4264
ELECTRICAL-BODY AND CHASSIS 8A-345
REMOVAL AND INSTALLATION
DOOR MIRROR CONTROL SWITCH
Removal
1. Disconnect the battery ground cable.
2. Door trim pad Assembly
Refer to section 10 “BODY” for door trim pad assembly
removal steps.
3. Door Mirror Control Switch
Remove the power window switch bezel.
Remove the screw.
Disconnect the switch connector.
To remove the switch panel assembly.
Installation
To install, follow the removal steps in the reverse order.
DOOR MIRROR
Removal and Installation
Refer to the DOOR MIRROR in section 10 “BODY”.