Suspension JAGUAR X308 1998 2.G Manual PDF

St
abilizer Bar Vehicles With: Supercharger

64.35.08
Rubber Suspension Insulator Lube
Castrol NTR
Removal
1.
CA
UTION:
Replacement of nuts and bolts: Various thread-locking devices are used on nuts and bolts
throughout the vehicle. These devices restrict the number of times a nut or bolt can be used. See
section <<100-00>>

for information.
Raise vehicle on a four-post lift. Refer to section <<100-02>>.
2.
Remove nuts and bolts securing stabilizer bar to links.
3.

Remove stabilizer bar mounting-brackets.
 Remove bolts.

In
stallation

1.
Posi ti
on monostrut on rear suspension.

2. Align m o
nostrut upper mountings and install but do not tighten
bolts

3. Ra
ise rear of suspension to
align with monostrut lower
mounting holes.

4. Inst al
l monostrut lower bolts and nuts and tighten to 77-103
Nm.
5. Tighten monostrut upper bolts to 88-118 Nm.

St
abilizer Bar Bushing Vehicles With: Supercharger

64.35.18
Rubber Suspension Insulator Lube
Castrol NTR
Removal
1.
CA
UTION:
Replacement of nuts and bolts: Various thread-locking devices are used on nuts and bolts
throughout the vehicle. These devices restrict the number of times a nut or bolt can be used. See
section <<100-00>>

for information.
Raise vehicle on a four-post lift. Refer to section <<100-02>>.
2.
Remove nuts and bolts securing stabilizer bar to links.
3.

Remove stabilizer bar mounting-brackets.
 Remove bolts.

Rear Suspension - Stabilizer Bar Mounting Frame
Remo
val and Installation
Remov
a
l
CAUTI
O
N: Replacement of
nuts and bolts: Various thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt can be used. See section 100-00 for information.
1. Ra
ise rear of vehicle and support
on stands. Refer to Section
100-02.

2. Support rear suspensio
n.
Posit
i
on a piece of wood under rear edge of suspension
unit.
Position an d
raise a jack
under wood to support
suspension unit.

3. Re
move monostrut lowe
r nuts and bolts.

4. Remove m
onostrut upper mounting
to body bracket securing
bolts.
5. Remove monostrut.
Lower rear edg
e
of suspension unit just sufficient for
access.
Exercising care to avoid dama ging fuel fil
ler neck drain
pipe, lift and withdraw monost rut from rear suspension.

Rear
Suspension -
Stabilizer Bar Mounting Frame Bushing
Re
moval and Installation
Remov

al
CAUTI
ON: Replacement of
nuts and bolts: Various thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt can be used. See section 100-00 for information.
I
nstallation
S
pecial Tool(s)

Adaptor Rin

g
204-116-01 (JD 143-1)

Anvil Adaptor
2
04-116-02 (JD 143-2)

R

emover/Replacer Adaptor
204-116-08 (JD 143-8)

D
ifferential Strut - Bush Replacer
204-201 (JD 241)
1. R
emove monostrut from
vehicle. Refer to operation 64.25.12.

2. Using a h
ydraulic press remove bush from monostrut.
Using special tools,

support monostrut on the press bed.
Posit

ion special tool on top of bush and align tool with
press ram.
Press bush from monostrut.

3. Clean relevant parts.
1. Using a hydraulic press, fi t bush into monostrut.
S
upport the bush-bore of the monostrut between
plates on the press-bed.

Rear
Suspension - Rear Wheel Bearing
Re
moval and Installation
S

pecial Tool(s)

Hub Holdin

g Tool
204-195 (JD227)

Hub Pu
ller
204-011 (JD 1D)

R
ear-Hub Remover
204-113 (JD 132)

Bearing Cu
p Replacer Adaptor
204-118 (JD 550-4/1)

Bearing Cu
p Replacer Adaptor
204-118 (JD 550-4/2)

D
river Handle
100-013 (18G-134)

Rear-hub spacer
replacer
204-003 (JD 15)
O
il Seal Remover/Replacer

Remove l
ocating collar.

17 . Install a th
read protector on axle shaft.

18 . R
elease hub from axle shaft.
Pos
i
tion hub puller 204-011 on hub studs.
Inst
al
l securing nuts.
Progres
s
ively tighten
puller center bolt to release hub from
axle shaft splines.
19. Remove hub puller an d thread protector.
Re
move securing nuts and
release puller from hub.
Re
move thread protecto
r from axle shaft.

20 . Relea
se parking brake cable
from suspension mounting
bracket.
Remove cable reta ining clip.

Draw c
a
ble through suspension mounting bracket
aperture.
21. Remove parking brake cable to hub carrier grommet.

35
.
Tighten hub nut to 304-336Nm.
36. Remove securing nuts and withdraw special tool 204-195
from hub.
37. Install rear wheel. Refer to Section 204-04.
38. Remove stands and lower vehi cle onto wheels. Refer to
section 100-02.
39. Raise vehicle on four-post lift.

40
.
Route parking brake cable through suspension mounting
bracket and secure with clip.

41
.
Route parking brake LH ca ble through equalizer.
42. Install LH cable in connecting clip.

Rear Suspension - Wheel Hub
Seal
Re
moval and Installation
Remov

al
S
pecial Tool(s)

Hub Holdin

g Tool
204-195 (JD227)

Hub Pu
ller
204-011 (JD 1D)

R
ear-Hub Remover
204-113 (JD 132)

O
il Seal Remover/Replacer
205-234 (JD 550-1)
1. CAUTION: Replacement of nuts and bolts: Various
thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt
can be used. See section 100-00 for information.
Release parking brake.
2. R
aise the vehicle on a four-post lift.

3. Fully
slacken but do not remove parking brake cable adjuster
nut.
4. Release appropriate side parkin g brake cable from connecting

19. Remove h
ub puller an
d thread protector.
Re
move securing nuts and
release puller from hub.
Re
move thread protecto
r from axle shaft.

20 . Relea
se parking brake cable
from suspension mounting
bracket.
Remove cable reta ining clip.

Draw c
a
ble through suspension mounting bracket
aperture.

21 . Remove parking brake cable to hu
b carrier grommet.

22 . Remove back plate.
Remove two bolts and two scre ws securing back plate
to
hub carrier.
With draw back plate
complete
with parking brake cable.
23. Mark wishbone at pivot pin eccentric flange marker to aid
installation.