rear suspension JAGUAR X308 1998 2.G Workshop Manual

                    Rear Toe  Adjustment  (57.65. 08) 
                     Whee
l
  Bearing  Circlip  Inspection  
                     Wheel Bearing  Inspection  
 
             204‐01:  Front  Suspension 
                 Specification  
                 Description  and  Operation  
                     Front Suspension  
                 Removal and  Installation  
                     Ball Joint  (60.15.02)  
                     Rear Lower  Arm  (60.35.54)  
                     Rear Lower  Arm  Bushing  (60.35.56)  
                     Front Shock  Absorber  (60.30.04)  
                     Spring 
                     Spring Seat  (60.20.03)  
                     Front Sta
bilizer  Bar  (60.10.01)  
                     Front Stabilizer  Bar  Bushing  (60.10.04)  
                     Front Stabilizer  Bar  Link  (60.10.02)  
                     Upper Arm  Bushing  
                     Front Wheel  Bearing  (60.25.40)  
                     Wheel Hub  
                     Wheel Knuckle  (60.25.23)  
                     Wheel Knuckle  and Wheel  Hub  Assembly  (60.25.38.90)  
                     Wheel Knuckle  and Wheel  Hub  Assembly  Conversion  (60.25.43)  
 
             204‐02:  Rear  Suspension 
                 Specif
ication  
                 Description  and  Operation  
                     Rear Suspension  
                 Removal and  Installation  
                     Axle Bump  Stop  (64.30.15)  
                     Rear Suspension  and Axle  Assembly  (64.25.01)  
                     Rear Shock  Absorber  (64.30.02)  
                     Shock Absorber  Lower  Bushing  (64.30.39)  
                     Spring (64.20.01)  
                     Rear Stabilizer  Bar  (64.35.08)  ‐ 4.0L  SC  V8 ‐ AJ26  
                     Rear Stabilizer  Bar  Bushing  (64.35.18)  ‐ 4.0L  SC V8 ‐ AJ26  

                    Stabilizer Bar  Mount i
ng
 Frame  (64.25.12)  
                     Stabilizer Bar  Mounting  Frame  Bushing  (64.25.13)  
                     Rear Wheel  Bearing  (64.15.14)  
                     Wheel Hub  Seal  (64.15.15)  
                     Wheel Knuckle  Bushing (64.15.24)  
 
             204‐04:  Wheels  and Tires  
                 Specification  
                 Description  and  Operation  
                     Wheels and Tires  
                 Diagnosis  and  Testing  
                     Wheels and Tires  
                 Removal and  Installation  
                     Whee
l  and  Tire  (74.20.05)  
 
             204‐05:  Vehicle  Dynamic  Suspension 
                 Description  and  Operation  
                     Vehicle Dynamic  Suspension  
                 Diagnosis  and  Testing  
                     Vehicle Dynamic  Suspension  
 
        205:  Driveline  
 
             205‐00:  Driveline  System  ‐ General  Information  
                 Description  and  Operation  
                     Driveline System  
 
             205‐01:  Driveshaft  
                 Specification  
                 Description  and  Operation  
                     Drives
haft 
                 Removal and  Installation  
                     Driveshaft (47.15.01) 
 
             205‐02:  Rear  Drive  Axle/Differential  
                 Specification  
                 Description  and  Operation  

Jacking and Lifting - Using the Workshop Jack
Gen
eral Procedures


1.
To raise
both
front wheels:
P
osition the jack centrally
under the front suspension
crossbeam.
Pla
ce a block of wood between the jack head and the
crossbeam.
R
aise the vehicle.
P

lace suitable vehicle stands
in position at the front
vehicle jacking points.
Lo
wer the vehicle onto the vehicle stands.

2. To raise
both rear wheels:
P

osition the jack centrally
under the rear suspension
subframe.
Pla
ce a block of wood between the jack head and the
subframe.
R
aise the vehicle.
P

lace suitable vehicle stands in
position at the rear vehicle
jacking points.
Lo
wer the vehicle onto the vehicle stands.

Suspension System - General Informatio
n -
Lubric
ants, Fluids, Sealants and Adhesives
Front Suspension Dimensions
• NO
TE: When a component reaches its maximum / minimum dimension limit the component must be replaced.
Rear sus
p
ension Dimensions
•
NO
TE: When a component reaches its maximum / minimum dimension limit the component must be replaced.
Vehicle ride
height


R i
de height is measured from
the center of the wheel to the apex of the wheel arch, through the wheel center line.
Showroom is with a
ll fluids at full an
d 9 liters (9.5 US quarts) of fuel.
Curb is
with all fluids at full and a full tank of fuel.
All f
i
gures quoted assume a ±
15 mm (0.59in) anticipated bu ild variance and condition.
Whee
l Alignment - Front Camber - XJR Excluding NAS, and German Super-8

Al l the above fi
gures
are at "showroom" height. (See ride height section above).
Tires must be infl
ated
to normal pressure.
For additional informat ion, refer to Section 204
-04
Wheels and Tires
.
Whe
e
l Alignment - Front Camber - XJR NAS, and Comfort/Sport/Daimler Super-8
UnitSp
ecification
Loctite27
0
Greas eShell Retin a
x 'A'
Greas
eCastro l 'NT
R'
Com
p
onent
Di
mensi
on
Hub face
-
maximum run-out
0.
03
8 mm
Com
p
onent
Di
mensi
on
Hub face
-
maximum run-out
0.
05
7 mm
Mod
e
l
Mod
e
l Year
V
I
N RANGE
Mark
et
Sh
owroom mm(in)
Curb mm(i
n)
FromToFron
t
RearFr
on
t
Rear
Com
f
ort suspension
1
998
to 2003.5
8
123
17
F
595
25
All3
90 (
15.11)
3
84 (
15.11)
3
89 (
15.31)
3
73 (
14.68)
Sport su
spe
nsion
"""All3
89 (
15.31)
3
81 (
15.00)
3
88 (
15.27)
3
72 (
14.64)
XJR"""NAS3
89 (
15.31)
3
82 (
15.03)
3
88 (
15.27)
3
72 (
14.64)
XJR"""RO
W367 (
14.44)
3
65 (
14.37)
3
66 (
14.40)
3
58 (
14.09)
Supercharged super 8"""All3
89 (
15.31)
3
82 (
15.03)
3
88 (
15.27)
3
72 (
14.64)
XJR

Excluding NAS, and German Super-8
1998 to

2003.5
VIN - 812317 to F59525
Units
Cambe r
Left
- Hand
Rig
h
t - Hand
Bal
a
nce (RH - LH)
MinMaxMinMaxMinMax
All Right-Hand driv
e and JapanDegrees
/minutes
-
1
° 28'
-0
°
28'
-
1
° 13'
-
0
° 13'
-0
° 45'+1 °
15'
Decimal degrees-1.
4
7°
-0
.4
7°
-1
.2
2°
-0.
2
2°
-0
.7
5°
+1
.25
°
R
e
st of World
De
grees
/minutes
-
1
° 13'
-0
°
13'
-
1
° 28'
-
0
° 28'
-1
° 15'+0 °
45'
Decimal degrees-1.
2
2°
-0
.2
2°
-1
.4
7°
-0.
4
7°
-1
.2
5°
+0
.75
°
XJR

NAS, and Comfort/Sport/Daimler Super-8
1
998 to
2003.5
VIN - 812317 to F59525
Units
Cambe r
Left
- Hand
Rig
h
t - Hand
Bal
a
nce (RH -
LH)
MinMaxMinMaxMinMax
All Right-Hand drive and JapanDegrees
/minutes
-1°
02'-0
° 02'
-0°

47'
+0°

13'
-0° 45'+1°

15'
Decimal degrees-1.0
3°
-0.0
3°
-0.7
8°
+0.22
°
-0.7
5°
+1.25
°
USA, Canada an
d Mexico,
Dominican
Republic (NAS)
De grees
/minutes
-0°
32 '+0 °

28'
-1 °

02'
-0 °
02'
-1°
30 '+0 °

30'
Decimal degrees-0. 5
3°
+0
.47
°
-1
.0
3°
-0
.0
3°
-1.
5
0°
+0
.50
°
R
e
st of World
De
grees
/minutes
-0°
47 '+0 °

13'
-1 °

02'
-0 °
02'
-1°
15 '+0 °

45'

Decimal degrees-0. 7
8°
+0
.22
°
-1
.0
3°
-0
.0
3°
-1.
2
5°
+0
.75
°

Suspension System - General Information - Front Camber and Caster
Adjust
ment
Gen
eral Procedures
• NOTE: Before any work is commenced, th e vehicle must be checked to establish that it conforms to the Jaguar original
specification, e.g. wheels, ti res, tire pressures, etc.
• NOTE: The vehicle must be unladen and the fuel tank full when measuring suspension geometry.

1.
Road test the vehicle to establish the exact nature of the
complaint, e.g. pulling to one side, wander.
2. Measure the suspension geometry, fill in the 'Suspension
Geometry Record Form', and co ntact Jaguar Technical Support
for assistance.
3. Technical Support will give advice on the course of action to be
taken to rectify the problem.
4. Each lower wishbone pivots on and is secured to the front
crossbeam by two fulcrum bolts. A circular eccentric flange
formed under the hexagonal head of each fulcrum bolt, has
raised graduation marks to indicate radial position. A washer
with a 'D' shaped hole locates on a flat on the threaded section
of each bolt. This ensures that the washer rotates with the bolt,
maintaining an eccentric position corresponding with the
flanged head. The outer face of the washer is punch marked,
ensuring correct instal lation with the chamfered face inwards.
This permits the washer to rotate freely in the crossbeam cam
reaction plate during a djustm ent. Each fulcrum bolt and
washer are secured by a self locking nut.
On rotation of the bolt, lateral movement of the eccentric flange
and washer is restricted by the cam plate faces, forcing the bolt
shank to move laterally in the crossbeam slots. Lateral
movement of the bolt shank re sults in corresponding inward
and outward movement of th e wishbone arm, effecting
adjustment of wh eel alignment.
Rotation of the front fulcrum bolt principally adjusts wheel
caster angle, with a small amount of camber angle change.
Adjustment of the rear fulcrum bo lt mainly alters wheel camber
angle with a small amount of caster angle change.
On vehicles with VIN up to 833124, fulcrum bolt eccentric
flanges have raised graduation marks representing 15 degree
increments of bolt rotati on from 0 to 90 degrees.
On vehicles with VIN from 833125, the fulcrum bolt graduation
marks represent bolt shank ho rizontal movement in 1mm
increments from 0 to 3mm.
The upper wishbone and fulcrum shaft are not adjustable and
play no part in steering geometry adjustment.

Suspension System - General Inform
ation - Rear Toe Adjustment
Gen
e
ral Procedures

1.
NOTE: Wheel alignment must not be carried out with a space
saver wheel installed on any of the hubs.
• NOTE: Before carrying out any ch ecking or adjustment of wheel
alignment, ensure that the vehicl e wheels, tires and tire pressures
are to Jaguar specification.
• NOTE: Before checking or ad justing rear wheel alignment,
examine the vehicle for curb impact damage on wheels and
subsequent damage to suspension components.
Position alignment checking equipment on road wheels and
following equipment manufacturer's instructions, check and if
necessary adjust rear wheel alignment to Specifications in
Section 204-02.

Front Suspension -
Lubri
cants, Fluids, Sealants and Adhesives
Press-In Loads
Torques


UnitS
pecification
Loctite27

0
Greas

e
Shell Retin
ax 'A'
Greas

e
Castro
l 'NTR'
Com

ponent
Kn
Ball join

t to upper wishbone
25
- 50
B

all joint to lower wishbone
25
- 50
Com

ponent
Nm
N

ut - ball joint, upper wishbone to vertical link.
60
-80
N

ut - ball joint, lower wishbone to vertical link.
60
-80
Nu

t - fulcrum bolt, upper wishbone.
60
-80
N

ut - ball joint, tie rod to steering arm.
71
-85
Bol

t - wheel speed sensor to vertical link.
8-1
0
Bol

t - front mounting to crossbeam.
22
-28
Bolt

- mounting , stabilizer bar.
30
-40
N

ut - link arm ball joint to stabilizer bar.
60
-80
Bolt

- mounting, steering rack to crossbeam.
41
-54
B

olt - front mounting, crossbeam to body.
22
-28
Bol

t - spring pan to lower wishbone.
70
-90
N

ut - shock absorber to upper mounting
(vehicles with adaptive damping).
16
-18
Nu

t - shock absorber to upper mounting (vehicles without adaptive damping).
30
-40
N

ut - shock absorber lower to wishbone.
43
-57
B

olt - engine Hydramount to crossbeam.
34
-46
B

olt - crossbeam rear mounting to body.
13
1-185
Bol

t - generator cooling du
ct deflector to crossbeam.
17
-23
N

ut - lower steering column to pinion shaft.
22
-28
N

ut - hub, speed sensor rotor.
27
0-330
B

olt - shield, brake disc.
9-1
2
Bol

t - lower wishbone, front arm to rear arm.
77
-103
Nu

t - stabilizer bar link arm to wishbone bracket.
41
-54
N

ut - wishbone front
eccentric bolt.
11
3-153
Nu

t - wishbone rear
eccentric bolt.
11
3-153
N

ut - fulcrum shaft, upper wishbone.
60
-80
Bolt -

power steering pi
pes to pinion housing.
9-1
2

Front C
rossbeam
A
fully stressed, pressed steel and tube fa
brication with integral lower wishbone tie bars, the crossbeam is secured to the
body on four resilient mountings.
The crossbeam incorporates mounting points for:
The u
pper and lower wish
bone fulcrum bolts.
The
stabilizer bar
The power steering rack. The engine h

ydramounts.
R

oad springs.
Slots and cam reaction pl ates on the crossbeam provide for ad justment of suspension geometry.
It
em
Par
t Number
De
scription
1—Cro

ssbeam
2—Upper

Wishbone
3—Lower Wi

shbone Arm, Front
4—Lower Wi

shbone Arm, Rear
5—Upper

Wishbone Ball Joint
6—Lower Wi

shbone Ball Joint
7—Ful

crum Bolt

8—Adjuster B
olt, Front
9—Adjuster B

olt, Rear
10—S

pring Pan
11—Shock Absorber Lower M

ounting Plate
12—Vertical Link


13—Hub Assembly
14—Sensor R

otor
15—B

olt, Wishbone to Link Arm

Upper
Wishbones
Each
upper wi
shbone assembly is a on
e-piece steel forging incorporating:
A pres
s-fit ball joint.
Press-fi

t bushes for location of the upper fulcrum bolt.
Lower Wishbones
Each l
o
wer wishbone comprising
forged steel front and rear arms bolted together, incorporates:
A p
ress-fit ball joint in the outer extremity of the rear arm.
Press-f
i
t bushes for location of the lower fulcrum bolts
Locati
on for the shock absor
b
er lower mounting plates.
Vertica l Links

The vertical
links are of forged steel
wi
th integral steering arms. Each is suppo rted between the upper and lower wishbones
by two ball joints and carries:
Front hub

Brake ca
liper and disc shield assembly

ABS se
nsor
.
Front Hub
s

Each f
o
rged steel front hub accommodates sealed for life cartridge
type wheel bearings, and carries:
The brake rotor assembl
y.
A
h
ub nut with toothed, integral ABS rotor.
Su
s
pension spring pi
n locking device.
Front Road
Springs
The road spri
ng
s are of coil type with their
rating dependent upon vehicle specification
Ea
ch spring is installed between the suspension crossbeam location and the lower wishbone spring pan.
Ru
bber seats ar
e installed betw
een the spring and the crossb eam and the spring pan.
Front Shock A
bsorbers
Th
e
shock absorbers are telescopic hydrau
lically operated units. Optional adaptive damping units incorporate a solenoid-
operated control valve at their upper extremity.
Each shoc
k absorber is installed between the lowe
r wishbone rear arm and a recess in the body.
The l
o
wer end of the shock absorber is se
cured to plates on the wishbone by a bolt that also serves as a pivot.
The u
pper en
d of each shock absorber is secured to the body location by a single nut.
Front Sta
b
ilizer Bar
A
front stabil
izer bar installed on all vehicles
is rated according to suspension specification.
Opera
tion
As each road wheel r
i
ses, move
ment is transmitted through the vertical link assembly to the lower wishbone. The resulting
rise of the wishbone compresses the road spring and partially telescopes the shock absorber. During this action, the spring
absorbs associated shocks and the shock absorber minimizes sprin
g os c
illation.

Du

ring cornering, vehicle weight
is transferred to the outer road wheel with a resulting tendency for the inner wheel to lift.
The stabilizer bar assists in minimizing this tendency by transf erring a proportion of potential lift of the inner wheel to the
outer wheel. This result s in enhanced body stability with improved corner ing capabilities.

Front Suspension - Rear Lower Arm
Remo
val and Installation
Remov
a
l
CAUTI
O
N: Replacement of
nuts and bolts: Various thread-locking devices are used on nuts and bolts throughout the
vehicle. These devices restrict the number of times a nut or bolt can be used. Refer to Section 100-00 for further
information.
S p
ecial Tool(s)

R
o
ad spring compressor
204-111 (JD115)

Taper separator
2
11-098 (JD 100)

Ball
Jo
int Taper Separator
204-192 (JD 219)

Bal l
joint splitter
204-293
1. Ra
ise front of vehicle and support on stands. Refer to Section
100-02.
2. Remove appropriate road wheel. Refer to Section 100-02.

3. CAUTIO
N: Do not suspend caliper from brake hose as
this will damage the hose.
Remove brake calipers from carriers. 1. Remove caliper spring clip.
2. Remove guide pin dust caps.
3. Slacken and withdraw guide pins.
4. Remove caliper from carrier and tie to suspension mounting bracket.
4. Ra
ise vehicle further to provid
e access for Special Tool 204-