wheel JAGUAR XFR 2010 1.G Workshop Manual

7. NOTE: Left-hand shown, right-hand similar.

Release the brake caliper.
Remove and discard the 2 bolts.
Tie the brake caliper aside.












8. NOTE: Left-hand shown, right-hand similar.
Disconnect the rear wheel speed sensor.











9. Disconnect the electronic parking brake actuator electrical
connector.













10. NOTE: Left-hand shown, right-hand similar.

Disconnect both parking brake cables from the rear brake
calipers.

System - V6 3.0L Petrol, Removal and Installation).

19. Refill the fuel tank.
For additional information, refer to: Fuel Tank Draining (310-00 Fuel System - General Information, General Procedures).

20. Bleed the brake system.
For additional information, refer to: Brake System Bleeding (206-00 Brake System - General Information, General Procedures).

21. Install the rear wheels and tires.
For additional information, refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

22. Connect the battery ground cable.
For additional information, refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

23. Using only four-wheel alignment equipment approved by Jaguar, check
and adjust the wheel alignment.
For additional information, refer to: Camber and Caster Adjustment (204-00 Suspension System - General Information, General Procedures).

204-269
Flange remover forcing screw

204-305
Remover, Wheel Bearing

204-725
Support Tool, Wheel Hub

204-726
Remover/Installer, Wheel Bearing

204-727A
Installer, Wheel Bearing

205-491
Hub puller

205-491-1
Adapter nuts Removal


1. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

2. Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

3.

Installation 14. Special Tool(s): 204-726
1. NOTES:


Make sure bearing is installed in correct direction,
encoder ring incorporated into the inboard seal of the wheel
bearing.


Make sure correct alignment of the bearing is
maintained when installing into the hub carrier.
Special Tool(s): 204-727A, 204-791

2.
3. NOTE: Make sure the correct alignment of the drive
flange is maintained when installing into the hub carrier
and bearing assembly.

Special Tool(s): 204-726, 204-250











4. CAUTION: The final tightening of the suspension
components must be carried out with the vehicle on its
wheels.

Torque: 90 Nm











5. CAUTION: Install the halfshaft nut finger tight.

NOTE: The wheel hub nut is not tightened at this
stage.

6. CAUTION: The final tightening of the suspension
components must be carried out with the vehicle on its
wheels.
Torque: 150 Nm












7. CAUTION: The final tightening of the suspension
components must be carried out with the vehicle on its
wheels.

Torque: 55 Nm











8. Torque: 6 Nm www.JagDocs.com

9.
10.
11.


















Torque: 103 Nm

















CAUTION: Do not use air tools to install the nut.
Failure to follow this instruction may result in damage to
the component.
Torque: 300 Nm









12. Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

Rear Suspension - Upper Arm
Removal and Installation

Removal Published: 18-Dec-2012

CAUTION: The final tightening of the suspension components must be carried out with the vehicle on its wheels.

NOTES:


Removal steps in this procedure may contain installation details.


RH illustration shown, LH is similar.

1. Raise and lower the vehicle on a 4 post ramp.


2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

3. Refer to: Wheel and Tire (204-04 Wheels and Tires, Removal and Installation).

4. Refer to: Shock Absorber and Spring Assembly (204-02, Removal and
Installation).

5.

Wheel nuts 125 92 - Tire Pressures
Summer Tyres (ROW) Up to 100 mph Over 100 mph 235/55R17 99W Front 2.3 bar (34 lbf/in²) 2.3 bar (34 lbf/in²) Rear 2.3 bar (34 lbf/in²) 2.3 bar (34 lbf/in²) 245/45R18 100 W&Y X/L Front 2.1 bar (31 lbf/in²) 2.6 bar (38 lbf/in²) Rear 2.1 bar (31 lbf/in²) 2.6 bar (38 lbf/in²) 245/40R19 98 Y X/L Front 2.1 bar (31 lbf/in²) 2.5 bar (36 lbf/in²) Rear 2.1 bar (31 lbf/in²) 2.5 bar (36 lbf/in²) 235/35R20 97Y X/L Front 2.3 bar (34 lbf/in²) 2.3 bar (34 lbf/in²) Rear - - 285/30R20 99y X/L Front - - Rear 2.3 bar (34 lbf/in²) 2.3 bar (34 lbf/in²) Tire Pressures
All Season Tyres (USA & Canada) 0 mph - 121 mph 245/45R18 96H Front 2.1 bar (31 lbf/in²) Rear 2.1 bar (31 lbf/in²) 245/40R19 94H Front 2.4 bar (35 lbf/in²) Rear 2.4 bar (35 lbf/in²) Wheel Specification
Wheel Type Wheel Size Libra 7.5 x 17 Cygnus 8.5 x 18 Venus 8.5 x 18 Auriga 8.5 x 19 Carelia 8.5 x 19 Volans (front) 8.5 x 20 Volans (rear) 9.5 x 20 Selena 8.5 x 20 Tires and Fitment

Description Wheels Type
Tire Type Vehicles with 2.7L Diesel and 3.0L engine Libra 235/55R17 99W Pirelli P7 Cygnus 245/45R18 100W Dunlop SP01 Vehicles without supercharger Cygnus 245/45R18 100W Dunlop SP01 Vehicles without supercharger (ROW) Venus 245/45R18 100Y Pirelli PZero Carelia 245/40R19 98Y Dunlop SP01 Auriga 245/40R19 98Y Dunlop SP01 Vehicles without supercharger (ROW) and vehicles with supercharger (USA &
Canada) Cygnus
245/45R18 96H Continental
ProContact Auriga
245/40R19 96H Continental
ProContact Vehicles with supercharger
Volans (front) 255/35R20 97Y Pirelli PZero Volans (rear) 285/30R20 99Y Pirelli PZero