JAGUAR XFR 2010 1.G Workshop Manual
XFR 2010 1.G
JAGUAR
JAGUAR
https://www.carmanualsonline.info/img/21/7642/w960_7642-0.png
JAGUAR XFR 2010 1.G Workshop Manual
Page 1224 of 3039
support the vehicle on safety stands.
Raise and support the vehicle.
10.
11. CAUTION: Lubricate only the union threads with clean engine oil.
NOTE: Engine shown removed for clarity.
Torque: Unions (1) 21 Nm M6 (2) 11 Nm M8 (3) 25 Nm M5 nut (4) 6 Nm
NOTE: Engine shown removed for clarity.
Torque: 21 Nm
Page 1225 of 3039
12.
13.
14. NOTES:
Install the bolt and unions finger tight before final tightening.
Remove and discard the blanking caps.
Torque: Unions 21 Nm M6 11 Nm
Torque: 21 Nm
NOTE: Engine shown removed for clarity.
Torque: M10 29 Nm M6 11 Nm
Page 1226 of 3039
15.
16. NOTE: Engine shown removed for clarity.
Torque: 25 Nm
17. Refer to: Generator - V8 5.0L Petrol (414-02C Generator and Regulator - V8 5.0L Petrol/V8 S/C 5.0L Petrol, Removal and Installation).
18. Refer to: Engine Mount RH (303-01D, In-vehicle Repair).
19. Lower the vehicle.
20.
Page 1227 of 3039
21. NOTES:
Lubricate
the
union
threads
with
clean
engine
oil.
Do
not tighten
at this
stage.
Remove
and
discard
the
blanking
caps.
22. Torque: Unions 21 Nm Bolts 8 Nm
23. Refer to: Air Cleaner Outlet Pipe RH (303-12D Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol, Removal and Installation).
24. www.JagDocs.com
Page 1235 of 3039
Installation
All vehicles
1. NOTE: Lubricate the fuel rail high-pressure fuel pump bucket with
clean engine oil.
2. CAUTION: Tighten on both sides simultaneously. Torque: 12 Nm
3. Loosen the Torx screws half a turn each. 4.
Page 1236 of 3039
5. CAUTION: Install new high-pressure fuel supply lines.
NOTES:
Engine shown removed for clarity.
Remove and discard the blanking caps.
Install the bolt and unions fully finger tight before final
tightening.
6. CAUTION: Care must be taken when positioning the fuel rail
high-pressure fuel pump cover to one side.
NOTE: Fuel rail high-pressure fuel pump cover shown removed for
clarity.
Torque: 12 Nm
7. Lower the vehicle.
8. NOTES:
Do not tighten at this stage.
Remove and discard the blanking caps.
9. WARNING: Do not work on or under a vehicle supported only by a jack. Always
support the vehicle on safety stands.
Page 1237 of 3039
Raise and support the vehicle.
10.
11. CAUTION: Lubricate only the union threads with clean engine oil.
NOTE: Engine shown removed for clarity.
Torque: Unions (1) 21 Nm M6 (2) 11 Nm M8 (3) 25 Nm M5 nut (4) 6 Nm
NOTE: Engine shown removed for clarity.
Torque: 21 Nm www.JagDocs.com
Page 1238 of 3039
12.
13.
14. NOTES:
Install the bolt and unions finger tight before final tightening.
Remove and discard the blanking caps.
Torque: Unions 21 Nm M6 11 Nm
Torque: 21 Nm
NOTE: Engine shown removed for clarity.
Torque: M10 29 Nm M6 11 Nm
Page 1239 of 3039
15.
16. NOTE: Engine shown removed for clarity.
Torque: 25 Nm
Left-hand drive vehicles
17. Torque: 100 Nm
Page 1240 of 3039
18. Torque: 35 Nm
All vehicles
19. Refer to: Generator - V8 5.0L Petrol (414-02C Generator and Regulator - V8 5.0L Petrol/V8 S/C 5.0L Petrol, Removal and Installation).
20. Refer to: Engine Mount RH (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
21. Lower the vehicle.
22.
23.
NOTES:
Lubricate
the
union
threads
with
clean
engine
oil.
Do
not tighten
at this
stage.
Remove
and
discard
the
blanking
caps.
