torque JAGUAR XFR 2010 1.G Workshop Manual

Published: 11-May-2011
Handles, Locks, Latches and Entry Systems - Front Door Lock Cylinder
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details.


1.





























2. NOTE: Remove the screw sufficiently, only to release
the component.
Torque: 4 Nm

Published: 11-May-2011
Handles, Locks, Latches and Entry Systems - Luggage Compartment Lid Latch
Actuator
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details.

1. Refer to: Luggage Compartment Lid Lock Cylinder (501-14 Handles, Locks, Latches and Entry Systems, Removal and Installation).




Installation

2. Torque: 20 Nm
1. To install, reverse the removal procedure.

Published: 11-May-2011
Handles, Locks, Latches and Entry Systems - Luggage Compartment Lid Lock Cylinder
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details.

1. Refer to: Luggage Compartment Lid Trim Panel (501-05 Interior Trim and Ornamentation, Removal and Installation).

2.
3. Torque: 3.2 Nm

Handles, Locks, Latches and Entry Systems - Rear Door Latch
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Remove the rear door window regulator and motor.

Refer to: Rear Door Window Regulator and Motor (501-11 Glass, Frames and Mechanisms, Removal and Installation).

2. Remove the rear door exterior handle.

Refer to: Exterior Rear Door Handle (501-14 Handles, Locks, Latches and Entry Systems, Removal and Installation).

3. Torque: 3 Nm 4.

Wipers and Washers - Windshield Wiper Motor
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Cowl Vent Screen (501-02 Front End Body Panels, Removal and Installation).


3. CAUTION: Tighten the bolts in the sequence shown.


NOTE: LHD illustration shown, RHD is similar.

Torque: 12 Nm










4. NOTE: LHD illustration shown, RHD is similar.
5. NOTE: LHD illustration shown, RHD is similar.

Wipers and Washers - Windshield Wiper Pivot Arm
Removal and Installation

Removal


CAUTION: Always protect paintwork and glass when removing exterior components.


1. Published: 11-May-2011
















Installation
















2. NOTE: Do not disassemble further if the component is
removed for access only.

1. Install the wiper blade.


2. CAUTION: Align the wiper blades onto the centre of the
windshield circle mark.


NOTE: After the wiper pivot arm nuts have been
tightened to the correct torque value, lift the wiper pivot
arm from the windshield and return to the windshield. Make
sure that wiper blades are not positioned below any point
of the windshield circle mark.

6. WARNING: This step requires the aid of another
technician.


NOTE: Note the fitted position of the spacers.
Torque: 8 Nm









7. NOTE: Do not disassemble further if the component is
removed for access only.

Torque: 4 Nm












8.

Roof Opening Panel - Roof Opening Panel Motor
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Overhead Console (501-12 Instrument Panel and Console, Removal and Installation).




Installation

2. Torque: 4 Nm
1. To install, reverse the removal procedure.

Bumpers - Front Bumper Cover
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011


1. WARNING: Make sure to support the vehicle with axle stands.

Raise and support the vehicle.

2. Torque: 3 Nm 3. Torque:
Retaining screws 2 Nm Retaining bolts 7 Nm

Bumpers - Rear Bumper Cover
Removal and Installation

Removal


NOTE: Removal steps may contain installation details. Published: 11-May-2011

1. Remove the rear lamp assemblies.

Refer to: Rear Lamp Assembly (417-01 Exterior Lighting, Removal and Installation).

2. Torque: 7 Nm 3.