suspension JAGUAR XFR 2010 1.G Service Manual

Suspension, Removal and Installation). www.JagDocs.com

Front Suspension - Shock Absorber Bushing
Removal and Installation

Special Tool(s)


Replacer support-bush
204-337

Replacer-bush
204-338

Remover-bush
204-336

Remover support-bush
204-335
Removal

CAUTION: Nuts and bolts must be tightened with the weight of the vehicle on the suspension. Published: 11-May-2011


1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise the vehicle on a 4 post lift.

2. Remove the rear lower arm.
For additional information, refer to: Rear Lower Arm (204-01 Front Suspension, Removal and Installation).

3. NOTE: Take note of the fitted position of the bush. Using
the special tools, remove the shock absorber bushing.









Installation


1. NOTE: Make sure the shock absorber bushing boot is
correctly located into the special tool.
Install the bushing into the special tool.








2. NOTE: Align to the position noted on removal.

Using the special tools, install the shock absorber bushing.










3. Install the rear lower arm.
For additional information, refer to: Rear Lower Arm (204-01 Front Suspension, Removal and Installation).

Published: 06-Jun-2013
Front Suspension - Front Stabilizer Bar V8 5.0L Petrol/V8 S/C 5.0L Petrol
Removal and Installation


Removal


NOTE: Removal steps in this procedure may contain installation details.

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise and support the vehicle.

3. Refer to: Air Conditioning (A/C) System Recovery, Evacuation and Charging (412-00 Climate Control System - General Information, General Procedures).

4. Refer to: Radiator Splash Shield (501-02 Front End Body Panels, Removal and Installation).

5. Refer to: Air Deflector (501-02 Front End Body Panels, Removal and Installation).

6. Refer to: Front Wheel Bearing and Wheel Hub - TDV6 3.0L Diesel /V8 5.0L Petrol/V8 S/C 5.0L Petrol (204-01 Front Suspension, Removal and Installation).

7. Refer to: Engine Cover - V8 5.0L Petrol/V8 S/C 5.0L Petrol (501-05 Interior Trim and Ornamentation, Removal and Installation).

8.
Secure the radiator assembly. 303-021
Engine support bracket Special Tool(s) www.JagDocs.com

Front Suspension - Stabilizer Bar Link Bushing
Removal and Installation

Special Tool(s)


Bush installer
204-340

Bush remove
204-342

Support
204-341

Support
204-339 Removal Published: 11-May-2011

CAUTION: The final tightening of the suspension components must be carried out with the vehicle on its wheels.


1. WARNING: Do not work on or under a vehicle supported only by a jack.
Always support the vehicle on safety stands.
Raise the vehicle on a 4 post lift.

2. Remove the rear lower arm.
For additional information, refer to: Rear Lower Arm (204-01 Front Suspension, Removal and Installation).

3. Using the special tools, remove and discard the stabilizer bar
link bushing.











Installation


1. NOTE: Apply water to lubricate the bushing.

Using the special tools, install the stabilizer bar link bushing.










2. Install the rear lower arm.
For additional information, refer to: Rear Lower Arm (204-01 Front Suspension, Removal and Installation). www.JagDocs.com

Suspension, Removal and Installation).

3. Remove the secondary bulkhead panel LH.
For additional information, refer to: Secondary Bulkhead Panel LH - 3.0L NA V6 - AJ27 (501-02 Front End Body Panels, Removal and Installation).
4. Remove the air cleaner.
For additional information, refer to: Air Cleaner (303-12A, Removal and
Installation) /
Air Cleaner (303-12B Intake Air Distribution and Filtering - V6 3.0L Petrol, Removal and Installation) /
Air Cleaner (303-12C, Removal and Installation) /
Air Cleaner LH (303-12D, Removal and Installation).


5. NOTE: Some variation in the illustrations may occur, but the
essential information is always correct.
Remove the upper arm retaining nut.












6. NOTE: Some variation in the illustrations may occur, but
the essential information is always correct.

Remove the upper arm retaining nut.

Suspension, Removal and Installation).


5. CAUTION: The final tightening of the suspension components
must be carried out with the vehicle on its wheels.


NOTE: Some variation in the illustrations may occur, but
the essential information is always correct.
Tighten to 47 Nm.








6. CAUTION: The final tightening of the suspension
components must be carried out with the vehicle on its wheels.


NOTE: Some variation in the illustrations may occur, but
the essential information is always correct.
Tighten to 47 Nm.






7. Install the air cleaner.
For additional information, refer to: Air Cleaner (303-12A, Removal and
Installation) /
Air Cleaner (303-12B Intake Air Distribution and Filtering - V6 3.0L Petrol, Removal and Installation) /
Air Cleaner (303-12C, Removal and Installation) /
Air Cleaner LH (303-12D, Removal and Installation).

8. Install the secondary bulkhead panel LH.
For additional information, refer to: Secondary Bulkhead Panel LH - 3.0L NA V6 - AJ27 (501-02 Front End Body Panels, Removal and Installation).

Suspension, Removal and Installation).

3. Remove the secondary bulkhead panel RH.
For additional information, refer to: Secondary Bulkhead Panel RH - 3.0L NA V6 - AJ27 (501-02 Front End Body Panels, Removal and Installation).

4. NOTE: Some variation in the illustrations may occur, but the
essential information is always correct.
Remove the upper arm retaining nut.












5. NOTE: Some variation in the illustrations may occur, but
the essential information is always correct.

Remove the upper arm retaining nut.












6. Remove the upper arm.

Suspension, Removal and Installation). www.JagDocs.com