instrument panel JAGUAR XFR 2010 1.G Manual Online

Seating - Seat Base
Removal and Installation

Removal

WARNINGS: Published: 11-May-2011

To avoid accidental deployment, the restraints control module backup power supply must be depleted. Wait at least one
minute after disconnecting the battery ground cable(s) before commencing any repair or adjustment to the supplemental
restraint system (SRS), or any component(s) adjacent to the SRS sensors. Failure to follow these instructions may result in
personal injury.


Always wear safety glasses when working on an air bag equipped vehicle and when handling an air bag module. Failure to
follow this instruction may result in personal injury.


To minimize the possibility of premature deployment, do not use radio key code savers when working on the
supplemental restraint system. Failure to follow this instruction may result in personal injury.


To minimize the possibility of injury in the event of premature deployment, always carry a live air bag module with the
bag and trim cover pointed away from the body. Failure to follow this instruction may result in personal injury.


To minimize the possibility of premature deployment, live air bag modules must only be placed on work benches which
have been ground bonded and with the trim cover facing up. Failure to follow these instructions may result in personal injury.


Never probe the electrical connectors of air bag modules or any other supplemental restraint system component. Failure
to follow this instruction may result in personal injury.


Painting over the driver air bag module trim cover or instrument panel could lead to deterioration of the trim cover and air
bags. Do not for any reason attempt to paint discolored or damaged air bag module trim covers or instrument panel. Install a
new component. Failure to follow this instruction may result in personal injury.
NOTES:


Some variation in the illustrations may occur, but the essential information is always correct.


Removal steps in this procedure may contain installation details.

1. Make the air bag supplemental restraint system (SRS) safe.

Refer to: Standard Workshop Practices (100-00 General Information, Description and Operation).

2. Refer to: Front Seat (501-10 Seating, Removal and Installation).
3. Refer to: Front Safety Belt Buckle (501-20A Safety Belt System, Removal and Installation).

4. Refer to: Front Seat Cushion Cover (501-10 Seating, Removal and Installation).

Instrument panel retaining bolts 20 15 - Floor console retaining nuts 5 - 44 Instrument panel support brackets retaining bolts 9 - 80 Instrument panel support brackets retaining nuts 9 - 80

Published: 11-May-2011
Instrument Panel and Console - Instrument Panel - Component Location
Description and Operation
COMPONENT LOCATION










































Item Description 1 Cross car beam 2 Glovebox switch 3 Energy absorbing brackets (2 off) www.JagDocs.com

a power supply to operate the glovebox latch to unlock the glovebox.

The glove box opening is inhibited by the CJB if the anti-theft alarm system is armed and if valet mode is selected using the Touch Screen Display (TSD). The CJB detects the voltage signal from the switch but will not operate the glovebox latch if other condition exists.



GLOVEBOX SWITCH DESCRIPTION Component Description

The conventional glove box switch is located behind the instrument panel veneer. The round button of the switch is visible
through an aperture in the veneer.

Two screws hold the switch in position behind the veneer. The veneer panel has two bosses which the screws are threaded
into.

Instrument Panel and Console - Floor Console
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Floor Console Cup Holder (501-12 Instrument Panel and Console, Removal and Installation).

3. CAUTIONS:


Protect the surrounding trim to avoid damage.


Cover fiber optic cable connectors to minimize dust
ingress and avoid bending the cables in a radius of less
than 30 mm.

Instrument Panel and Console - Floor Console Cup Holder
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Floor Console Double Cup Holder (501-12 Instrument Panel and Console, Removal and Installation).

3.
4. CAUTION: Take extra care not to damage the
component.


NOTE: Do not disassemble further if the component is
removed for access only.

Published: 11-May-2011
Instrument Panel and Console - Floor Console Double Cup Holder
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details.

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).

2. Refer to: Transmission Control Switch (TCS) (307-05A Automatic Transmission/Transaxle External Controls - V6 3.0L Petrol, Removal and
Installation).

3.
4.
5. www.JagDocs.com

Instrument Panel and Console - Floor Console Side Trim Panel
Removal and Installation

Removal

NOTES: Published: 11-May-2011

LHD right-hand floor console side trim panel shown, LHD left-hand and both RHD floor console side trim panels are
similar.


Removal steps in this procedure may contain installation details.

1. Recline the front seats and move to the rear most position.


2. NOTE: When removing the component, some of the clips
may remain attached. These clips should be removed and
returned to their original positions in the instrument
panel.













3.
4.

Instrument Panel and Console - Glove Compartment
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Passenger Side Register (412-01 Climate Control, Removal and Installation).

2.
3. CAUTION: Fixings must be started by hand to avoid
damaging threads.

Upper 3 bolts.

Torque: 2.5 Nm Lower 3 bolts.

Torque: 9 Nm

Instrument Panel and Console - Instrument Panel Console
Removal and Installation Published: 11-May-2011


Removal

CAUTIONS:


Inspect the seals, replace if damaged.
Inspect the O-rings, replace if damaged.
NOTE: Removal steps in this procedure may contain installation details.

All vehicles

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

Vehicles with supercharger

3. Refer to: Cooling System Draining, Filling and Bleeding - V8 S/C 5.0L Petrol (303-03C Engine Cooling - V8 5.0L Petrol/V8 S/C 5.0L Petrol, General Procedures).

Vehicles without supercharger

4. Refer to: Cooling System Draining, Filling and Bleeding - V8 5.0L Petrol (303-03C Engine Cooling - V8 5.0L Petrol/V8 S/C 5.0L Petrol, General
Procedures).

Vehicles with diesel engine

5. Refer to: Cooling System Draining, Filling and Bleeding (303-03A Engine Cooling - TDV6 3.0L Diesel, General Procedures).

All vehicles

6. Refer to: Air Conditioning (A/C) System Recovery, Evacuation and Charging (412-00 Climate Control System - General Information, General Procedures).

7. Refer to: Secondary Bulkhead Center Panel (501-02 Front End Body Panels, Removal and Installation). 303-1496
Heater Hose Removal Tool Special Tool(s)
www.JagDocs.com