pinpoint JAGUAR XFR 2010 1.G Manual Online
[x] Cancel search | Manufacturer: JAGUAR, Model Year: 2010, Model line: XFR, Model: JAGUAR XFR 2010 1.GPages: 3039, PDF Size: 58.49 MB
Page 239 of 3039
DTC Description Possible Causes Action speed control sensor, check and install a new sensor
as required, refer to the new module/component
installation note at the top of the DTC Index C1A67-96 Forward Looking Sensor
- Component internal
Failure
Internal hardware failure
Suspect the speed control sensor. Check and install a
new sensor as required, refer to the new
module/component installation note at the top of
the DTC Index C1A67-97 Forward Looking Sensor
- Component or system
operation obstructed or
blocked
Sensor reduced visibility
Check for blockage in front of radar. Note: This DTC
will be cleared automatically when environmental
conditions allow C1A67-98 Forward Looking Sensor
- Component or system
over temperature
Speed control sensor
internal temperature
exceeded threshold
Allow system to cool. Note: This DTC will be cleared
automatically when environmental conditions allow P174E-81
Output Shaft
Speed/ABS Wheel
Speed Correlation -
Invalid serial data
received
Follow speed is
mis-calculated to too
high a value
Clear DTC and re-test U0001-88
High Speed CAN
Communication Bus -
Bus off
Vehicle CAN Bus off
condition
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Carry out CAN network integrity tests using
the manufacturer approved diagnostic system U0100-00
Lost Communications
With ECM/PCM "A" - No
sub type information
ECM missing message
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check ECM for related DTCs and refer to the
relevant DTC Index U0101-00
Lost Communications
With TCM - No sub
type information
TCM missing message
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check TCM for related DTCs and refer to the
relevant DTC Index U0103-00
Lost Communication
With Gear Shift Control
Module A - No sub type
information
No sub type information
Refer to the electrical circuit diagrams and check the
power and ground connections to the Transmission
Shift Module. Using the manufacturer approved
diagnostic system, complete a CAN network integrity
test. Refer to the electrical circuit diagrams and
check the CAN network between the Transmission
Shift Module and Speed Control Module U0103-87
Lost Communication
With Gear Shift Module
- Missing Message
Transmission shift
module missing message
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check transmission shift module for related
DTCs and refer to the relevant DTC Index U0121-00
Lost Communication
With Anti-lock Brake
System (ABS) Control
Module - No sub type
information
ABS missing message
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check ABS for related DTCs and refer to the
relevant DTC Index U0128-00
Lost Communications
With Park Brake Module
- No sub type
information
Parking brake missing
message
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check parking brake module for related
DTCs and refer to the relevant DTC Index U0155-00
Lost Communications
With Instrument Panel
Cluster (IPC) Control
Module - No sub type
information
Instrument cluster
missing message
Carry out any pinpoint tests associated with this
DTC using the manufacturer approved diagnostic
system. Check instrument cluster for related DTCs
and refer to the relevant DTC Index
Page 242 of 3039
Published: 17-Apr-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Steering
Column Lock Module (VIM)
Description and Operation
Steering Column Lock Module (VIM)
CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault and may also cause additional faults in the vehicle being checked and/or the donor vehicle.
NOTES:
If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the
Warranty Policy and Procedures manual, or determine if any prior approval programme is in operation, prior to the installation
of a new module/component.
Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer approved diagnostic system).
When performing voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal places,
and with an up-to-date calibration certificate. When testing resistance, always take the resistance of the DMM leads into
account.
Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
If DTCs are recorded and, after performing the pinpoint tests a fault is not present, an intermittent concern may be the
cause. Always check for loose connections and corroded terminals.
Where an 'on demand self-test' is referred to, this can be accessed via the 'DTC Monitor' tab on the manufacturers
approved diagnostic system.
Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as required.
The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Steering Column Lock Module, for
additional Diagnosis and Testing information refer to the relevant Diagnosis and Testing Section.
For additional information, refer to: Steering Column Switches (211-05 Steering Column Switches, Diagnosis and Testing).
DTC Description Possible Causes Action B100D-51
Column Lock
Authorisation - Not
programmed
Module not programmed
Configure the Steering Column Lock Module using the
manufacturers approved diagnostic system B100D-62
Column Lock
Authorisation -
Signal compare
failure
Signal compare failure
- This DTC will be
logged if the
encrypted data
exchange does
not match
between Steering
Column Lock and
the Central
Junction Box
Configure the modules using the manufacturers approved
diagnostic system. If the problem persists, complete a
CAN network integrity test using the manufacturers
approved diagnostic system. Perform an on demand
self-test and retest B100D-64
Column Lock
Authorisation -
Signal plausibility
failure
Signal plausibility failure
Steering Column Lock
unable to perform lock
action
CAN Network fault
Anti-lock Braking
System, Engine Control
Module, Central Junction
Box fault
NOTE: Prior to clearing this DTC, carry out the Vehicle
Functional Reset application using the manufacturer approved
diagnostic system
Check the serviceability of the steering column and lock.
Clear the DTC and retest. If the problem persists, carry
out CAN Network Integrity Test and Module Self Test
using the manufacturer approved diagnostic system.
Alternatively, refer to the electrical circuit diagrams and
Page 244 of 3039
Published: 12-May-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Television
Module (TVM)
Description and Operation
Television Control Module (TVCM)
CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.
NOTES:
If a control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty
Policy and Procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new
module/component.
Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system).
When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places, and with
an up-to-date calibration certificate. When testing resistance always take the resistance of the digital multimeter leads into
account.
Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the
cause. Always check for loose connections and corroded terminals.
Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as required.
The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Television Control Module (TVCM). For
additional diagnosis and testing information, refer to the relevant Diagnosis and Testing section in the workshop manual.
For additional information, refer to: Information and Entertainment System (415-00 Information and Entertainment System - General Information, Diagnosis and Testing).
DTC Description Possible Causes Action B1A56-11
Antenna - Circuit
short to ground
Antenna circuit
short to ground
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna circuit for short to ground B1A56-12
Antenna - Circuit
short to battery
Antenna circuit
short to power
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna circuit for short to power B1A56-13
Antenna - Circuit
open
Antenna circuit
open circuit
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna circuit for open circuit B1D55-11
Antenna#2 - Circuit
short to ground
Antenna #2
circuit short to
ground
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #2 circuit for short to
ground B1D55-12
Antenna#2 - Circuit
short to battery
Antenna #2
circuit short to
power
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #2 circuit for short to power
Page 245 of 3039
DTC Description Possible Causes Action B1D55-13
Antenna#2 - Circuit
open
Antenna #2
circuit open
circuit
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #2 circuit for open circuit B1D56-11
Antenna #3 Circuit -
Circuit short to
ground
Antenna #3
circuit short to
ground
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #3 circuit for short to
ground B1D56-12
Antenna #3 Circuit -
Circuit short to
battery
Antenna #3
circuit short to
power
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #3 circuit for short to power B1D56-13
Antenna #3 Circuit -
Circuit open
Antenna #3
circuit open
circuit
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #3 circuit for open circuit B1D57-11
Antenna #4 Circuit -
Circuit short to
ground
Antenna #4
circuit short to
ground
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #4 circuit for short to
ground B1D57-12
Antenna #4 Circuit -
Circuit short to
battery
Antenna #4
circuit short to
power
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #4 circuit for short to power B1D57-13
Antenna #4 Circuit -
Circuit open
Antenna #4
circuit open
circuit
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check antenna #4 circuit for open circuit B1D58-11 Television Output -
Circuit short to
ground
Television output
circuit short to
ground
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check television output circuit for short to
ground B1D58-12 Television Output -
Circuit short to
battery
Television output
circuit short to
power
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check television output circuit for short to
power B1D58-13 Television Output -
Circuit open
Television output
circuit open
circuit
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system. Refer to electrical
circuit diagrams and check television output circuit for open
circuit U3000-49
Control Module -
Internal electronic
failure
Internal
electronic failure
Suspect the television module, check and install a new module
as required, refer to the new module/component installation
note at the top of the DTC Index U3003-16
Battery Voltage -
Circuit voltage below
threshold
Circuit voltage
below threshold
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system U3003-17
Battery Voltage -
Circuit voltage above
threshold
Circuit voltage
above threshold
Carry out any pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system
Page 246 of 3039
Published: 17-Apr-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Tire
Pressure Monitoring System Module (TPM)
Description and Operation
Tire Pressure Monitoring System (TPM)
CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault and may also cause additional faults in the vehicle being checked and/or the donor vehicle.
NOTES:
If the control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the
Warranty Policy and Procedures manual, or determine if any prior approval programme is in operation, prior to the installation
of a new module/component.
Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer approved diagnostic system).
When performing voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal places,
and with an up-to-date calibration certificate. When testing resistance, always take the resistance of the DMM leads into
account.
Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
If DTCs are recorded and, after performing the pinpoint tests a fault is not present, an intermittent concern may be the
cause. Always check for loose connections and corroded terminals.
Where an 'on demand self-test' is referred to, this can be accessed via the 'DTC Monitor' tab on the manufacturers
approved diagnostic system.
Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as required.
The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Tire Pressure Monitoring System, for
additional Diagnosis and Testing information refer to the relevant Diagnosis and Testing Section.
For additional information, refer to: Wheels and Tires (204-04 Wheels and Tires, Diagnosis and Testing).
DTC Description Possible Causes Action C1A56-31
Left Front Tire Pressure
Sensor and Transmitter
Assembly - No signal
Missing, incompatible or
defective tire pressure
sensor or radio frequency
receiver
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test F in section 204-04,
Diagnosis and Testing, Wheels and Tires C1A56-68
Left Front Tire Pressure
Sensor and Transmitter
Assembly - Event
information
Information only - vehicle
exposed to extreme
temperature environment
and/or tire pressure
sensor low battery
voltage event
No action required C1A56-91
Left Front Tire Pressure
Sensor and Transmitter
Assembly - Parametric
Tire pressure sensor has
reported out of range
information for pressure,
temperature or
acceleration
Replace defective tire pressure sensor. Refer to
the relevant section of the workshop manual C1A56-93
Left Front Tire Pressure
Sensor and Transmitter
Assembly - No operation
No tire pressure sensor
can be localized at this
position due to an
initiator or tire pressure
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test G in section 204-04,
Diagnosis and Testing, Wheels and Tires www.JagDocs.com
Page 247 of 3039
DTC Description Possible Causes Action sensor malfunction
C1A57-11
Left Front Initiator -
Circuit short to ground
Left front initiator circuit
is short to ground
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test B1 in section 204-04,
Diagnosis and Testing, Wheels and Tires C1A57-12
Left Front Initiator -
Circuit short to battery
Left front initiator circuit
is short to power
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test B2 in section 204-04,
Diagnosis and Testing, Wheels and Tires C1A57-13
Left Front Initiator -
Circuit open
Left front initiator circuit
open
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test B9 in section 204-04,
Diagnosis and Testing, Wheels and Tires C1A58-31
Right Front Tire Pressure
Sensor and Transmitter
Assembly - No signal
Missing, incompatible or
defective tire pressure
sensor or radio frequency
receiver
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test F in section 204-04,
Diagnosis and Testing, Wheels and Tires C1A58-68
Right Front Tire Pressure
Sensor and Transmitter
Assembly - Event
information
Information only - vehicle
exposed to extreme
temperature environment
and/or tire pressure
sensor low battery
voltage event
No action required C1A58-91
Right Front Tire Pressure
Sensor and Transmitter
Assembly - Parametric
Tire pressure sensor has
reported out of range
information for pressure,
temperature or
acceleration
Replace defective tire pressure sensor. refer to
the relevant section of the workshop manual C1A58-93
Right Front Tire Pressure
Sensor and Transmitter
Assembly - No operation
No tire pressure sensor
can be localized at this
position due to an
initiator or tire pressure
sensor malfunction
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test G in section 204-04,
Diagnosis and Testing, Wheels and Tires C1A59-11
Right Front Initiator -
Circuit short to ground
Right front initiator circuit
is short to ground
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test C1 in section 204-04,
Diagnosis and Testing, Wheels and Tires C1A59-12
Right Front Initiator -
Circuit short to battery
Right front initiator circuit
is short to power
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test C2 in section 204-04,
Diagnosis and Testing, Wheels and Tires C1A59-13
Right Front Initiator -
Circuit open
Right front initiator circuit
open
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test C9 in section 204-04,
Diagnosis and Testing, Wheels and Tires C1A60-31
Left Rear Tire Pressure
Sensor and Transmitter
Assembly - No signal
Missing, incompatible or
defective tire pressure
sensor or radio frequency
receiver
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test F in section 204-04,
Diagnosis and Testing, Wheels and Tires C1A60-68
Left Rear Tire Pressure
Sensor and Transmitter
Assembly - Event
information
Information only - Vehicle
exposed to extreme
temperature environment
and/or tire pressure
sensor low battery
voltage event
No action required
Page 248 of 3039
DTC Description Possible Causes Action C1A60-91
Left Rear Tire Pressure
Sensor and Transmitter
Assembly - Parametric
Tire pressure sensor has
reported out of range
information for pressure,
temperature or
acceleration
Replace defective tire pressure sensor, refer to
the relevant section of the workshop manual C1A60-93
Left Rear Tire Pressure
Sensor and Transmitter
Assembly - No operation
No tire pressure sensor
can be localized at this
position due to an
initiator or tire pressure
sensor malfunction
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test G in section 204-04,
Diagnosis and Testing, Wheels and Tires C1A61-11
Left Rear Initiator -
Circuit short to ground
Left rear initiator circuit
short to ground
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test D1 in section 204-04,
Diagnosis and Testing, Wheels and Tires C1A61-12
Left Rear Initiator -
Circuit short to battery
Left rear initiator circuit
short to power
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test D2 in section
204-04,Diagnosis and Testing, Wheels and Tires C1A61-13
Left Rear Initiator -
Circuit open
Left rear initiator circuit
open
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test D9 in section 204-04,
Diagnosis and Testing, Wheels and Tires C1A62-31
Right Rear Tire Pressure
Sensor and Transmitter
Assembly - No signal
Missing, incompatible or
defective tire pressure
sensor or radio frequency
receiver
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test F in section 204-04,
Diagnosis and Testing, Wheels and Tires C1A62-68
Right Rear Tire Pressure
Sensor and Transmitter
Assembly - Event
information
Information only - vehicle
exposed to extreme
temperature environment
and/or tire pressure
sensor low battery
voltage event
No action required C1A62-91
Right Rear Tire Pressure
Sensor and Transmitter
Assembly - Parametric
Tire pressure sensor has
reported out of range
information for pressure,
temperature or
acceleration
Replace defective tire pressure sensor, refer to
the relevant section of the workshop manual C1A62-93
Right Rear Tire Pressure
Sensor and Transmitter
Assembly - No operation
No tire pressure sensor
can be localized at this
position due to an
initiator or tire pressure
sensor malfunction
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test G in section 204-04,
Diagnosis and Testing, Wheels and Tires C1A63-11
Right Rear Initiator -
Circuit short to ground
Right rear initiator circuit
short to ground
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test E1 in section 204-04,
Diagnosis and Testing, Wheels and Tires C1A63-12
Right Rear Initiator -
Circuit short to battery
Right rear initiator circuit
short to power
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing). Go to pinpoint test E2 in section 204-04,
Diagnosis and Testing, Wheels and Tires C1A63-13
Right Rear Initiator -
Circuit open
Right rear initiator circuit
open
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test E9 in section 204-04,
Diagnosis and Testing, Wheels and Tires
Page 249 of 3039
DTC Description Possible Causes Action C1A64-68
Spare Wheel Tire
Pressure Sensor and Transmitter Assembly -
Event information
Information only - vehicle
exposed to extreme
temperature environment
and/or tire pressure
sensor low battery
voltage event
No action required C1A64-91
Spare Wheel Tire
Pressure Sensor and Transmitter Assembly -
Parametric
Tire pressure sensor has
reported out of range
information for pressure,
temperature or
acceleration
Replace defective tire pressure sensor, refer to
the relevant section of the workshop manual C1A64-93
Spare Wheel Tire
Pressure Sensor and Transmitter Assembly -
No operation
Missing, incompatible or
defective tire pressure
sensor or radio frequency
receiver
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test H in section 204-04,
Diagnosis and Testing, Wheels and Tires C1D19-11
External Receiver Data
Line - Circuit short to
ground
Tire pressure monitoring
system radio frequency
receiver or data line
circuit is short to ground
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test A in section
204-04,Diagnosis and Testing, Wheels and Tires C1D19-12
External Receiver Data
Line - Circuit short to
battery
Tire pressure monitoring
system radio frequency
receiver or data line
circuit is short to power
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test I in section 204-04,
diagnosis and testing C1D19-87
External Receiver Data
Line - Missing message
Radio Frequency
reception blocked
Tire pressure monitoring
system radio frequency
receiver faulty
Tire pressure monitoring
system radio frequency
receiver or data line
circuits open circuit
Missing, incompatible or
defective tire pressure
sensors
For additional information, refer to: Wheels and
Tires (204-04 Wheels and Tires, Diagnosis and
Testing).Go to pinpoint test J in section 204-04,
Diagnosis and Testing, Wheels and Tires U0010-88
Medium Speed CAN
Communication Bus - Bus
off
CAN bus fault
Carry out CAN network integrity tests. Refer to
the electrical wiring diagrams and check CAN
network for short, open circuit U0140-00
Lost communication with
body control module - No
sub type information
CAN bus fault
Central junction box fault
Refer to the electrical wiring diagrams and check
central junction box power and ground supplies
for short, open circuit. Carry out CAN network
integrity tests U0142-00
Lost Communication With
Body Control Module "B" -
No sub type information
CAN bus fault
Rear junction box fault
Refer to the electrical wiring diagrams and check
rear junction box power and ground supplies for
short, open circuit. Carry out CAN network
integrity tests U0155-00
Lost Communications
With Instrument Panel
Cluster (IPC) Control
Module - No sub type
information
CAN bus fault
Instrument cluster fault
Refer to the electrical wiring diagrams and check
instrument cluster power and ground supplies for
short, open circuit. Carry out CAN network
integrity tests U0164-00
Lost Communication With
HVAC Control Module - No
sub type information
CAN bus fault
Climate control module
fault
Refer to the electrical wiring diagrams and check
climate control module power and ground supplies
for short, open circuit. Carry out CAN network
integrity tests
Page 251 of 3039
Published: 12-May-2014
General Information - Diagnostic Trouble Code (DTC) Index DTC: Touch
Screen Display (FCDIM)
Description and Operation
Touch Screen (TS)
CAUTION: Diagnosis by substitution from a donor vehicle is NOT acceptable. Substitution of control modules does not
guarantee confirmation of a fault, and may also cause additional faults in the vehicle being tested and/or the donor vehicle.
NOTES:
If a control module or a component is suspect and the vehicle remains under manufacturer warranty, refer to the Warranty
Policy and Procedures manual, or determine if any prior approval programme is in operation, prior to the installation of a new
module/component.
Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan tool to
the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system).
When performing voltage or resistance tests, always use a digital multimeter accurate to three decimal places, and with
an up-to-date calibration certificate. When testing resistance always take the resistance of the digital multimeter leads into
account.
Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may be the
cause. Always check for loose connections and corroded terminals.
Check DDW for open campaigns. Refer to the corresponding bulletins and SSMs which may be valid for the specific
customer complaint and carry out the recommendations as required.
The table below lists all Diagnostic Trouble Codes (DTCs) that could be logged in the Touch Screen (TS). For additional
diagnosis and testing information, refer to the relevant Diagnosis and Testing section in the workshop manual.
For additional information, refer to: Information and Entertainment System (415-00 Information and Entertainment System - General Information, Diagnosis and Testing).
DTC Description Possible Causes Action B100E-25
Video Input 'A' - Signal
shape/waveform
failure
ODST Only - TV video
synch mis-match
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system B100F-25
Video Input 'B' - Signal
shape/waveform
failure
ODST Only - Reverse
Camera video synch
mis-match
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system U1A01-01
Communication Link -
General electrical
failure
ODST Only - cable
from navigation
module not correctly
installed
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system.
Check electrical harness from navigation module is
correctly installed U1A01-15
Communication Link -
Circuit short to battery
or open
TSD to navigation
module circuit - short
to power, open circuit
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system.
Refer to the electrical circuit diagrams and check TSD to
navigation module circuit for short to power, open circuit U1A4B-48
Control Module
Processor B -
Supervision software
failure
Supervision software
failure
Re-configure the TSD using the manufacturer approved
diagnostic system www.JagDocs.com
Page 252 of 3039
DTC Description Possible Causes Action U3000-44
Control Module - Data
memory failure
EEPROM, External
RAM access failure
Suspect the TSD, check and install a new TSD as
required, refer to the new module/component
installation note at the top of the DTC Index U3000-48
Control Module -
Supervision software
failure
Supervision software
failure
Re-configure the TSD using the manufacturer approved
diagnostic system U3000-4B
Control Module - Over
temperature
Touch panel backlight
- high temperature
detected
Allow the system to cool, clear the DTC and
check/monitor system for re-occurrence. If DTC re-occurs
suspect the TSD. Check and install a new TSD as
required, refer to the new module/component
installation note at the top of the DTC Index U3000-55
Control Module - Not
configured
Incorrect Car
Configuration
Parameters received
Check/amend Car Configuration File using the
manufacturer approved diagnostic system U3000-87
Control Module -
Missing message
Car Configuration File
not received
Check RJB for related DTCs and refer to relevant DTC
Index. Check CAN and MOST networks, carry out the
CAN and MOST network tests using the manufacturer
approved diagnostic system U3000-98
Control Module -
Component or system
over temperature
TSD internal
temperature over
limit
Allow the system to cool, clear the DTC and
check/monitor system for re-occurrence. If DTC re-occurs
suspect the TSD. Check and install a new TSD as
required, refer to the new module/component
installation note at the top of the DTC Index U3003-16
Battery Voltage -
Circuit voltage below
threshold
Circuit voltage below
threshold
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system U3003-17
Battery Voltage -
Circuit voltage above
threshold
Circuit voltage above
threshold
Carry out any pinpoint tests associated with this DTC
using the manufacturer approved diagnostic system