fuse JAGUAR XJ6 1994 2.G Workshop Manual

Introduction
FOREWORD
This Vehicle Service Manual (VSM) is Dart
-
of a
set of service literature which covers -. diagnosis and rectification of problems associated with all areas of the X300 family of vehicles.
It is designed to be read in conjunction with other manuals, namely the various Unit Service Manuals (USM) (as
applicable to the particular vehicle under diagnosis/ repair) and the X300 Electrical Diagnostic Manual (EDM); see list
below.
It should be noted that its scope is limited to those areas that are unique to the family, e.g. Remove & Refit procedures
for Body Components, Engine, Transmission etcetera, Fuel, Emissions & Engine Management systems, and so on.
Fault Diagnosis and repair procedures (together
with Technical Data, Recommended Lubricants, Capacities etcetera) for major assemblies such as engines, automatic and manual transmissions, are covered in the separate Unit Service
Manuals.
The Unit Service Manuals are notvehicle
-specific, but are designed to be read in conjunction with this VSM, and, where so equipped, with other Jaguar Vehicle Service Manuals for new models launched subsequent to the X300 family.
The X300 Electrical Diagnostic Manual is the final part of the 'set' of service documentation. This manual
is
family-specific, and is designed to aid theTechnician to isolate electrical faults and to correct them. It covers all aspects
of electrical fault diagnosis, including:
OBD
II Codes and emission control system related fault diagnosis / rectification.
Circuit Diagrams
Component (Relays, fuse boxes, control modules etcetera) Location
/ Harness Diagrams I Ground Locations
Connector Locations.
Service Manuals Required
The Manuals required to service the X300 family of vehicles are as follows:
X300 Vehicle Service Manual
X300 Electrical Diagnostic Manual
Unit Service Manuals:
AJ16 Engine Service Manual
VI2 Engine Service Manual ZF AutomaticTransmissions Service Manual (ZF supplies transmissions for 3.2 liter and 4.0 liter normally aspirated
versions) Powertrain Automatic Transmissions Service Manual (The Powertrain name succeeds that of Hydra
-Matic.
Powertrain are suppliers of the 4L 80 E transmission as fitted to 4.0 litre supercharged and 6.0 litre versions)
Each
of the X3Okpecific manuals is divided into Sections which adopt the same title and number where relevant, i.e. Section 5.1 of both the VSM and the EDM cover Fuel, Emission Control & Engine Management System (AJ16). An
over
-all contents list showing each section title and number together with its page-edge locator is given in this section
and in the introduction to the EDM.
The VSM (not applicable to the EDM) also contains Appendices which cover specialized areas such as the current
vehicle specification, routine maintenance schedule etc. These are carried at the rear of this Manual, and have their
own contents page within this section.
INDEX
rapid location of information. The entries are set out as per the following example: @ This manual carries a comprehensive index at the rear, which is designed to save the Technician time by permitting
CLIMATE CONTROL SYSTEMS. Section 14.
See also Electrical Diagnostic Manual
Clutch
Description: Sect. 7.7 - 10
Fault diagnosis: Sect 7.1 - 11
In the example the heading in upper case lettering is to a section title, and it refers to the section number, 14, and also to the EDM as electrical diagnostic information will be found in that manual's section 14. The entry for clutch tells us that the relevant description will be found on page 10 of Section 7.1 of this manual, and
that fault diagnosis procedures start on page 11. In this case there is no reference to the EDM as electrical diagnosis does not apply to this area.
GLOSSARY OF TERMS
This Section contains a Glossary of general and emissions-related terminology (commencing on page 5).
X300 VSM 1 Issue 1 August 1994

(if applicable) term(s) (or Eng- lish Equivalent)
N
National Institute of Occupational NIOSH Safety & Health (US)
Newton N SI unit of force. 1 N = 0.2248 pounds force
Newton meters Nm
SI unit of torque. Must not be confused with nm (nanometer)
compounds of nitrogen and oxygen formed
at high temperatures. Major source of
exhaust
-gas air-pollution
RAM which retains memory even if power
N
Ox
NVRAM
Memory supply is interrupted
normally aspirated fueling system using intake air at
atmospheric pressure; not supercharged or
turbocharged
Normally Closed NC
Normally Open NO
North American Specification NAS vehicles for sale
in the USA and Canadian
markets
0
I number I No.
octane number
I
I open circuit
I oriainal eauiDment manufacturer
I outside diameter OSHA
OBD
OEM
0. dia
OHC
oc
N Ox
02s
measure ofthe anti-knockproperties ofafuel
instrument which records the total mileage
covered by a vehicle
a system that monitors some or all computer
input and output control signals.
Signal(s) outside the pre-determined limits imply a
fault in the svstem or a related svstem
a circuit which does not provide a complete
path for flow of current
engine configuration with single camshaft
positioned above the valves
catalytic converter system that reduces
levels
of HC and CO
a sensor which detects oxygen content in the
exhaust gases mileometer
oilwav
EGO,
02 EOS,
EGS, OS, EGOS,
Lambda Sensor
Issue 1 August 1994 20 X300 VSM

Term(s) Abbreviation Definition Previously used
(if applicable) term(s) (or Eng-
lish Equivalent)
T
tachometer
Thermal Vacuum Valve
Three
-way Catalytic Converter
Three
-way + Oxidation Catalytic
Converter TWC + OC
Throttle
------I
Throttle Body TB
Throttle Position TP
Throttle Position Sensor TPS
throw
-out bearing
throw
-out fork
tie
-rod (steering)
timing
tire
top dead center TDC
torque converter
Transmission
Transmission Control Module
Transmission Control Switch
Transmission Oil Temperature TOT
Transmission Range TR
I Transmission Speed Sensor TSS
tread
trunk
turn indicator, turn signal lamp
two cycle a
circuit that provides input for an electronic
tachometer display
controls vacuum levels or routing based on
temperature
catalytic converter that reduces the levels of
HC,
CO & NOx
catalyticconverter systemthat has both TWC
and OC. Usually secondary air is introduced
between the two catalvsts
procedure whereby the performance of a
product is measured under various
conditions - - . -. . . - . . -
a valve for regulating the supply of a fluid,
usually air or an aidfuel mixture, to an engine
device containing the throttle
interprets throttle position and movement to
identify idle, acceleration and full
-power
demands
relationship between spark plug firing and
piston position, usually expressed
in crankshaft degrees BTDC or ATDC of the
compression stroke
device which, by its design, multiplies the
torque in a fluid coupling between an engine
and transmission
device which selectively increases or
decreases the ratio of relative rotation
between its
inDut and outDut shafts
controls the shifting pattern of the
(automatic) transmission
Modifies the operation of electronically
controlled transmissions
indicates temperature
of transmission fluid
the range in which the transmission is
operating
indicates rotational speed of transmission
output shaft or turbine
shaft
track between tire contact centers; not to be
confused with tire contact tread pattern
principle of engine which fires every second
stroke of the piston cat
cat, dual bed
Throttle poten
-
tiometer, TPS, TP
clutch release
bearing
clutch release
lever
track rod
tvre
TCC, CCC, CCO,
LUS, MLUS,
MCCC
transmission
ECU
track boot, luggage
compartment
direction indica
- tor
two stroke
Issue 1 August 1994 26 X300 VSM

13.4 TRUNK
13.4.1 Trunk, Description
The trunk houses the spare wheel, the battery, an electrical carrier containing electrical fuses, relays and modules and
a compact disc auto-changer attached to body bracketry. The trunk is fitted with push-fit, velour finish, liners (1 Fig. 1) to the sides and front inner panel; the trunk floor is covered with carpet attached to a removable floor board (2 Fig. 1) and a battery cover (3 Fig. I), one covering the spare wheel and wheel changing equipment, the other covering the
battery and electrical carrier.
The floor board rests on the spare wheel, the front and rear edges
of the floor board locating in blocks on the fuel tank
backboard and on the rear of the body. The blocks accommodate the two possible height settings caused by the differ- ence in thickness between the space saver and full sized spare wheels.
A tread plate (4 Fig. 1) is attached to the trunk sill and a liner is fitted to the rear of the trunk below the sill. Interior trim finisher panels are fitted to the rear lamp units accessed from the trunk opening.
The trunk lid
(5 Fig. 1) is fitted with a removable moulded liner and two trunk illumination lights; the lid is supported by two gas struts, attached through press-on fittings between the inner wheel arch and trunk hinge (6 Fig. 1). A warning
triangle is attached by a bracket to the trunk lid and retained in the open position by a rubber block (Europe inc UK only).
Trunk locking is based on a central latch and striker, operated electrically through the central locking system
by an ad- jacent actuator or by key in a barrel lock located behind the trunk lid badge.
For details on renewal
of trunk front and side liners, trunk carpet, trunk seal retainer and battery cover, see relevant
Service Repair Operations.
2 4 3 J76-1056
1. Trunk Liners 2. Removable floor board 3. Battery cover
4. Treadplate 5. Trunk lid 6. Hinge
Fig.
1 Trunk Components and Trim
Issue 1 August 1994 X300 VSM 38

Body Components & Trim a
13.5 HOOD
13.5.1 Hood, Description
The hood is fitted with black moulded covers over the inner fenders and behind the headlamp units; the right hand
fender cover incorporates compartments for spare fuses and tool kit (where fitted). Two gas struts attached by press- on fittings on the body and hood support the hood cover.
13.5.2 Plenum Chamber Finisher, Renew
SRO 76.10.01
9 Open the hood and fit suitable fender cover.
. Remove the wiper arm, see section 15.6.
. Undo and remove the plenum chamber finis..er securing
. Displace and reposition the plenum chamber.
. Disconnect the washer jet tubes.
9 Disconnect the washer jet multi-plugs.
. Displace the washer jet securing tangs.
. Displace and remove the washer jets (2 Fig. 1).
. Place the finisher aside.
. Fit and fully seat the washer jets to the new plenum
. Connect the washer jet multi-plugs.
9 Reconnect the washer jet tubes.
. Position the plenum chamber finisher.
. Fit and tighten the finisher securing screws.
. Refit the wiper arm.
9 Remove the fender cover and close the hood.
screws
(1 Fig. 1).
chamber
finisher.
13.5.3 Hinge, Renew
. Disconnect vehicle battery ground lead.
. Open hood and fit fender protectors.
. Remove radiator grille.
. 12 cylinder only:
. Remove fan cowl to top panel clips and move the cowl as-
sembly clear.
. Move water bleed pipe from top panel clips.
. Release fixings and remove radiator top mounting panel.
. Remove hinge securing nuts RH or LH (ground lead on the
CAUTION: Ensure that the hood cover is adequately sup- ported and that paint damage cannot occur.
. Remove hinge bolts RH or LH, noting the position of the
ground lead on the left hand side.
. To refit, carry out reversal of the above procedure, ensur- ing that the hood should be fully aligned before finally
torque tightening the fixings.
left
hand side).
I
0
Fig. 1
X300 VSM Issue 1 August 1994 42

Key to Fig. 1, Battery Power Distribution Cables, page 22.
Rear heel board 1 Fuse box power lead 1
Terminal to terminal post link lead 2
Engine bay 1 fuse box power cable LH 3
Starter to alternator cable 4
Engine bay 1 fuse box power cable RH 5
Batt.ry Power Distribution Cabb Numb
1 Starter cable I 6 I
Battery positive extension cable 7
Battery positive cable 8
Battery negative cable 9
Trunk fuse box power cable 10

Black
Black
Black All
models
All Models
All Models
Black
Black All
Models
All Models
Black/
White Stripe
Black/
White Stripe
Black Non
Aircon.
Models
only
Non Power
Wash Models
only
Optional
0 Key to Fig. 1, hgine Compartment Relays, page 14.
Number v12 Color
All Models
SRO
B6.55.04
Rdaw
Horn
Location
Engine
compartment,
inside the left
hand side fuse box.
Engine
compartment,
behind left hand head
lamp assembly.
see starter
motor
solenoid. All
Models
1 ~~
All
Models 5 Starter Motor
Solenoid
4 All Models
All Models 18.30.34 Air-conditionin
g Water Pump
Wiper Motor
On
/Off
2 see starter
motor
solenoid.
see starter
motor
solenoid. All
Models
3 Wiper Fast /
Slow
18.30.71 Engine
compartment, behind right
hand head
lamp assembly. 8 EMS Engine
Management
System
Control
Black
I
All Models 9 Ignition Coil
PI Main Relay see
EMS
control.
see EMS
control. Black
I
All
Models 8
Air Pump 7 see EMS
control.
see EMS
control. Black
Air Injection
Black Air Con
- Model Air
Injection
only
All Models
18.30.34
86.55.08 Air
Conditioning
Compressor
Clutch
Relay Case
Engine
compartment,
on the right
hand side inner
wing valance.
Relay
Case Non Power
Wash
Models
only
11
10
12
Power Wash
Screen Wash Optional
All Models
All Models
Black
All Models
Ignition Relay
Engine
compartment,
inside
right
hand fuse box.
X300 VSM 33 Issue 1 August 1994

I SRO I Rdw* AJ16 v12
Automatic Automatic
Models only Models only
Automatic Automatic
Models only Models only
UK
& ROW -
Manual Seat
only
UK
& ROW -
Manual Seat
onh/
UK & ROW -
Manual Seat
only
Manual Seat
only
UK
& Manual -
Seat only
UK
& Manual -
Seat only
UK
& ROW -
Optional
Optional
Optional Optional
Keylock
Number
13
14
15
16
34
35
17
36
37
38
Driver's Seat Height
Control (Upward)
Driver's Seat Height
Control (Downward)
Passenger Seat
Height Control (Upward)
Passenger Seat
Height Control
(Downward)
Driver's Seat Heater
All Models
All Models
All Models
Passenger Seat
Heater
RH Front
Screen
Heater
LH Front Screen
Heater
Ignition All Models
25
All Models 26
All Models 23
Ignition
Air
-conditioning
Isolate
LH Blower
RH Blower
LH Blower
high
speed
RH Blower high
speed
Deadlock front
lefthear right All
Models All Models
20
Below gear selector 'J' gate.
Not NAS or
Japan
UK
& Europe
only
All Models
All Models
USA
&
Canada only
All Models
All Models
All Models
All Models
Below
gear selector
'J' gate.
Not NAS or
30
UK & Europe 31
All Models 28
All Models 29
USA & 27
All Models 24
All Models 33
All Models 22
All Models 32
Japan
only
Canada only
On
seat panel below
driver's seat.
86.55.78
86.55.74
On seat panel below
driver's seat.
Deadlock front
righthear left
Door Lock
Door Unlock
Driver's Door
Unlock
Mirror Heater
Puddle Lamps
Cigar Lighter
Fuel Flap Lock On
seat panel below
passenger's seat.
On seat panel below
passenger's seat.
On seat panel below
driver's seat.
On seat panel below
passenger's seat.
Left hand side footwell on
front
'A' post, behind cover.
Left hand side footwell on
front
'A' post, behind cover.
Fuse box assembly
RH side heelboard.
Fuse box assembly
LH side heelboard.
Behind
RH side heelboard.
Behind
RH side heelboard.
Behind RH side heelboard.
Behind
RH side heelboard.
Behind
RH side heelboard.
Behind LH side heelboard.
Behind LH side heelboard.
Behind LH side heelboard.
Behind LH side heelboard.
Behind LH side heelboard.
Behind
RH side heelboard.
Behind LH side heelboard.
Behind
RH side heelboard.
Behind LH side heelboard.
Color
Blue
Blue
Violet
Violet
Violet Violet Blue Blue
Blue
Blue
Blue
Blue
Blue
Blue
Blue Blue
Blue
Violet
Violet
Violet
Violet
Violet
Violet Blue
Blue
Violet All
Models All Models
All Models All Models
All Models All Models
18
X300 VSM 35 Issue 1 August 1994

rl Electrical
'5.12.3 Trunk Relays, General DescrptiOn
05
04
03
02
1
18
I
2-
U 37
038
Fig. 1 Trunk Relays
JW 1681
Fig.1 shows all relays located inside the trunk. To locate and renew relays, open the trunk lid, remove the wheel floor
carpet board, followed by the carpeted battery/fuse cover and the back panel carpet board.

Electrical IT
Key to Fig. 1, Trunk Relays, page 18.
, 86.55.73 Trunk Lid Release
Accessory
Socket
86.56.10 High Mount Stop
86.56.11 Fuse box Assembly/
! Aux. Positive
X300 VSM 37 Issue 1 August 1994