reverse KIA CARNIVAL 2007 Workshop Manual

5.Installation is the reverse of removal.
GLASS REPLACEMENT
1.Remove the following items.
a. Door trim.
b. Door belt weather strip.
c. Rear channel.
a.Take care not to drop to glass and scratch the glass surface.
2. Carefully move the glass (A) until you can see the bolts, then loosen them. Separate the glass run from the door
panel and carefully pull the glass out through the window slot.
3.Installation is the reverse of removal.
a.Roll the glass up and down to see if it will move freely without binding.
b. Make sure that there is no gap between the glass and glass run channel when the glass is closed.
c. Adjust the position of the glass as necessary.
POWER WINDOW MOTOR REPLACEMENT
1.Remove the rear door trim.

2.After disconnecting the connector (B), remove the power window motor (A).
3.Installation is the reverse of removal.
a.Roll the glass up and down to see if it move will freely without binding.
OUT SIDE HANDLE REPLACEMENT
1.Remove the following items.
a. Door trim.
b. Door trim seal.
c. Actuator.
2. Loosen the mounting bolt, then remove the outside handle bracket (A).
3.Remove the outside handle (A).

4.Installation is the reverse of removal.
a.Make sure the door locks and opens properly.
LATCH ASSEMBLY REPLACEMENT
1.Remove the following parts.
a. Door trim.
b. Door trim seal.
2. Disconnect the connector.
3. Loosen the latch mounting screws, remove the latch (A).
4.Installation is the reverse the removal.
a.Make sure the door lock and opens properly.
REGULATOR ASSEMBLY REPLACEMENT
1.Remove the following parts.
a. Door trim.
b. Door trim seal.
c. Glass.

2.Disconnect the connector (B).
3. After loose the dooring module mounting nuts, remove the window regulator (A).
4.Installation is the reverse of removal.
a.Make sure the connector is plugged in properly and each rod is connected securely.
b. Make sure the door lock and open properly.
INSIDE HANDLE REPLACEMENT
1.Disconnect the clip (A), remove the inside handle (B).
2.Installation is the reverse of removal.
a.Make sure the door lock and open properly.
CHANNEL REPLACEMENT
1.Remove the door trim.
2. Remove the glass.
3. Loosen the channel mounting nuts, remove the channel (A).

4.Installation is the reverse of removal.
DOOR ACTUATOR REPLACEMENT
1.Remove the inside handle.
2. Remove the door trim.
3. Remove the door trim seal.
4. Disconnect the connector (A) and cable (B).
5.After loosening the mounting bolts and nuts, then remove the actuator assembly (A).

6.Disconnect the outside handle cable (A).
7.Installation is the reverse of removal.
DOOR BELT WEATHERSTRIP REPLACEMENT
1.Loosen the mounting screw, then remove the door belt weather strip (A).
2.Installation is the reverse of removal.
DOOR MOTOR REPLACEMENT
1.Remove the rear combination ramp.
2. After loosening the rail cover mounting bolts, then remove the rail cover (A).
3.Remove the rear cable (A).

8.Installation is the reverse of removal.
ADJUSTMENT
GLASS ADJUSTMENT
a. Check the glass run channel for damage or deterioration, and replace them necessary.
1. Remove the following parts.
a. Door trim.
2. Carefully move the glass (A) until you can see the glass mounting bolts then loosen them.
3.Push the glass against the channel then tighten the glass mounting bolts.
4. Check that the glass moves smoothly.
5. Raise the glass fully, and check for gaps. check that the glass contacts the glass run channel evenly.
6. Check for water leaks. Run water over the roof and on the sealing area as shown, and note these items:
a. Use a 12mm (1/2in.) diameter hose (A).
b. Adjust the rate of water flow as shown (B).
c. Do not use a nozzle.
d. Hold the hose about 300mm(12in.) away from The door.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
ROOF RACK REPLACEMENT
a. When prying with a flat- tipped screwdriver, wrap it with protective tape, and apply protective tape around the
related parts, to prevent damage.
b. Put on gloves to protect your hands.
c. Take care not to scratch the body surface.
1. Remove the roof rack cover (A).
2. Remove the roof rack (B), by removing nut protector covers, and removing the nuts.
3. Installation is the reverse of removal.
FRONT MUD GUARD AND WHEEL GUARD REPLACEMENT

a.When prying with a flat- tipped screwdriver, wrap it with protective tape, and apply protective tape around the
related parts, to prevent damage.
b. Put on gloves to protect your hands.
c. Take care not to scratch the body surface.
1. Remove the wheel guard (B) first by removing the clip and screw, then remove the wheel guard(A), by removing
the screws and clip.
2.Installation is the reverse of removal.
REAR MUD GUARD AND WHEEL GUARD REPLACEMENT
a.When prying with a flat- tipped screwdriver, wrap it with protective tape, and apply protective tape around the
related parts, to prevent damage.
b. Put on gloves to protect your hands.
c. Take care not to scratch the body surface.
1. Remove the wheel guard (B) first by removing the clip and screw, then remove the wheel guard(A), by removing
the screws and clip.
2.Installation is the reverse of removal.
SIDE GARNISH AND SIDE SILL REPLACEMENT

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
OUTSIDE REAR VIEW MIRROR RELPLACEMENT
a. When prying with a flat- tipper screwdriver, wrap it with protective tape, and apply protective tape around the
related parts, to prevent damage.
b. Put on gloves to protect your hands.
1. Remove the quadrant inner cover (A).
2.Remove the door trim.
3. After disconnecting the connector (A), remove the outside rear view mirror (B).
4.Installation is the reverse of removal.
INSIDE REAR VIEW MIRROR REPLACEMENT
1.Push the inside rear view mirror base (A) down to remove to inside rear view mirror assembly (B).