reverse KIA CARNIVAL 2007 Workshop Manual

3.Installation is the reverse of removal.
SHROUD REPLACEMENT
1.Loosen the screws.
2. Disconnect the connector, then remove the shroud assembly (A).
3.Installation is the reverse of removal.
LOWER CRASH PAD PANEL REPLACEMENT
1.Remove the glove box.
2. Remove the side air vent.
3. Remove the DVD cover (A).

9.Installation is the reverse of removal.
CRASH PAD REPLACEMENT
a.When prying with a flat- tipped screwdriver, wrap itwith protective tape, and apply protective tapearound the
related parts, to prevent damage.
b. Put on gloves to protect your hands.
1. Remove the following items.
a. Front seat.
b. Cluster facia panel, cluster.
c. Audio assembly.
d. Glove box.
e. Side cover, center under cover.
f. Front pillar trim.
2. Remove the photo sensor (C), speaker connector (B).
3. Disconnect the passenger`s air bag connector (A).
Loosen the bolt and nut, then remove the crash pad (D).
4. Installation is the reverse of removal.
a.Make sure the crash pad fits onto the guide pins correctly.
b. Before tightening the bolts, make sure the crash pad wire harnesses are not pinched.
c. Make sure the connectors are plugged in properly, and the antenna lead is connected properly.
d. Enter the anti- theft code for the radio, then enter.
[LHD]

COWL CROSS BAR ASSEMBLY REPLACEMENT
a.When prying with a flat- tipped screwdriver, wrap it with protective tape, and apply protective tape around the
related parts, to prevent damage.
b. Put on gloves to protect your hands.
1. Remove the crash pad.
2. Remove the connectors.
3. Loosen the bolts and nuts, then remove cowl cross bar assembly (A).
4. Installation is the reverse of removal.
a.Make sure the crash pad fits onto the guide pins correctly.
b. Before tightening the bolts, make sure the crash pad wire harnesses are not pinched.
c. Make sure the connectors are plugged in properly, and the antenna lead is connected properly.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
SUNVISOR REPLACEMENT
1. Loosen the mounting screws, then sunvisor (A) and holder (B).
2. Disconnect the connector (C).
3.Installation is the reverse of removal.
S/G CASE REPLACEMENT
1.Using a screwdriver, remove the side tray (A).
2.Installation is the reverse of removal.
REAR HEATER CONTROL UNIT REPLACEMENT
1.Remove the rear heater control unit (A).
2. Disconnect the connector (B).

ASSIST HANDLE REPLACEMENT
1.Remove the assist handle (A).
2.Installation is the reverse the removal.
OVERHEAD CONSOLE REPLACEMENT
1.Loosen the overhead console mounting screws, remove the overhead console assembly (A).
2. Disconnect the connector (B).
3.Installation is the reverse the removal.
ROOF AIR VENT REPLACEMENT
1.Using a screwdriver, remove the roof air vent (A).

2.Installation is the reverse the removal.
ROOM LAMP REPLACEMENT
1.Remove the room lamp.
a. Remove the lens (A).
b. Remove the screw.
c. Pull out the room lamp (B).
d. Disconnect the connector (C).
2.Installation is the reverse of removal.
ROOF TRIM REPLACEMENT
a.When prying with a flat- tipped screwdriver, wrap it with protective tape, and apply protective tape around the
related parts, to prevent damage.
b. Put on gloves to protect your hands.
1. Remove the following item.
a. Sunvior.
b. Assist handle.
c. Side tray.
2. Using a clip remover, detach the clips, and remove the roof trim (A).
3. Installation is the reverse the removal.
a.Replace any damage clips.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
FRONT DOOR SCUFF TRIM REPLACEMENT
a. Put on gloves to protect your hands.
b. When prying with a flat- tipped screwdriver, wrap it with protective tape to prevent damage.
c. Take care not to bend or scratch the trim and panels.
1. Remove the front door scuff trim (A).
2.Installation is the reverse of removal.
a.Replace any damaged clips.
REAR DOOR SCUFF TRIM REPLACEMENT
a.Put on gloves to protect your hands.
b. When prying with a flat- tipped screwdriver, wrap it with protective tape to prevent damage.
c. Take care not to bend or scratch the trim and panels.
1. Remove the rear door scuff trim (A).

2.Installation is the reverse of removal.
a.Replace any damage clips.
FRONT PILLAR TRIM
a.Put on gloves to protect your hands.
b. When prying with a flat- tipped screwdriver, wrap it with protective tape to prevent damage.
c. Take care not to bend or scratch the trim and panels.
1. Remove the front pillar trim (A).
2.Installation is the reverse of removal.
a.Replace any damage clips.
COWL SIDE TRIM REPLACEMENT

a.Put on gloves to protect your hands.
b. When prying with a flat- tipped screwdriver, wrap it with protective tape to prevent damage.
c. Take care not to bend or scratch the trim and panels.
1. Remove the front door scuff trim.
2. Remove the cowl side trim (A).
3.Installation is the reverse of removal.
a.Replace any damage clips.
CENTER LOWER PILLAR TRIM REPLACEMENT
a.Put on gloves to protect your hands.
b. When prying with a flat- tipped screwdriver, wrap it with protective tape to prevent damage.
c. Take care not to bend or scratch the trim and panels.
1. Remove the front seat belt lower anchor.
2. Remove the front door scuff trim.
3. Remove the rear door scuff trim.
4. Remove the center lower pillar trim (A).

5.Installation is the reverse of removal.
a.Replace any damage clips.
CENTER UPPER PILLAR TRIM REPLACEMENT
a.Put on gloves to protect your hands.
b. When prying with a flat- tipped screwdriver, wrap it with protective tape to prevent damage.
c. Take care not to bend or scratch the trim and panels.
1. Remove the center lower pillar trim.
2. Remove the center upper pillar trim (A).
3.Installation is the reverse of removal.
a.Replace any damage clips.
REAR PILLAR TRIM REPLACEMENT