reverse KIA CARNIVAL 2007 Workshop Manual

a.Put on gloves to protect your hands.
b. When prying with a flat- tipped screwdriver, wrap it with protective tape to prevent damage.
c. Take care not to bend or scratch the trim and panels.
1. Remove the luggage trim.
2. Remove the tailgate lift (A).
3. Remove the rear pillar upper trim (B).
4.Installation is the reverse of removal.
a.Replace any damage clips.
C PILLAR TRIM REPLACEMENT
a.Put on gloves to protect your hands.
b. When prying with a flat- tipped screwdriver, wrap it with protective tape to prevent damage.
c. Take care not to bend or scratch the trim and panels.
1. Remove the luggage trim.

2.Remove the C pillar trim(A).
LUGGAGE SIDE TRIM REPLACEMENT
a.Put on gloves to protect your hands.
b. When prying with a flat- tipped screwdriver, wrap it with protective tape to prevent damage.
c. Take care not to bend or scratch the trim and panels.
1. Remove the rear door scuff trim.
2. Remove the fire extinguisher.
3. Remove the transverse trim.
4. Remove the luggage side trim (A).
5. Installation is the reverse of removal.

2.Remove the rear pillar trim.
3. Loosen the mounting screw.
4.After loosening the quarter glass mounting bolts, then remove the quarter glass (A).
5.Installation is the reverse of removal.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
FRONT BUMPER COVER REPLACEMENT
a. Put on gloves to protect your hands.
b. When prying with a flat- tipped screwdriver, wrap it with protective tape to prevent damage.
c. Take care not bend or scratch the cover and other parts.
1. Disconnect the connector (C).
2. Remove the headlamp (B), under cover (A).
3. Loosen the front bumper mounting screws and clips.
4. Remove the front bumper.
5. Remove the connector (C).
6. Installation is the reverse of removal.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
REAR BUMPER COVER REPLACEMENT
a. When prying with a flat- tipped screwdriver, wrap it with protective tape , and apply protective tape around the
related parts your hands.
b. Put on gloves to protect your hands.
c. Take care not bend or scratch the cover and other parts.
1. Remove the rear combination ramp(A).
2. Loosen the rear bumper screws and clips.
3. Remove the rear bumper.
4. Installation is the reverse of removal.
a.Replace any damage clips.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
SEAT ASSEMBLY REPLACEMENT
1. Remove the seat assembly mounting cover.
2. After loosening the seat assembly mounting bolts, remove the seat assembly (A).
3.Open the connector box (A).
4. Disconnect the connector (B), and remove the seat assembly.
5.Installation is the reverse of removal.
SEAT MOUNTING BOLT INSTALLATION PROCEDURE
a. Set the into the most rearward position.
Check then each slide is locked, and then Tighten the front mounting bolt temporarily.
b. Set the seat into most forward position.
Check that each slide is locked, and then Tighten the rear mounting bolt completely.
c. Set the seat into the most rearward position.
Check the front mounting bolt completely.
d. Check that the seat operates to and fro smoothy and the locking portion locks properly.
LUMBAR SUPPORT LEVER REPLACEMENT
1.Loosen the lumber support lever mounting screw, remove the lumber support lever (A).
2. Installation is the reverse of removal.

RECLINER COVER REPLACEMENT
1.Remove the cover (A).
2.Loosen the recliner mounting screw and clip, then remove the recliner cover (A).
3.Installation is the reverse of removal.
ARMREST REPLACEMENT
1.Remove the cover (A).

2.After the armrest mounting bolt, then remove the armrest (B).
3.Installation is the reverse of removal.
SEAT BACK COVER REPLACEMENT
1.Remove front seat assembly.
2. Remove the recliner cover.
3. Remove the armrest.
4. Remove the connector (A), (B).
5.After disconnecting the scuff band (A), remove the seat back panel (B).
6.Remove the headrest and headrest guide (A).

10.After removing the hog- ring clips (A) on the front of seat back remove the seat back cover (B).
11.Installation is the reverse of removal.
a. To prevent wrinkles, make sure the material is stretched evenly over the cover (A) before securing the hogring
clips (B)
b. Replace the hogring clips with new ones using special tool (C).
SEAT CUSHION COVER REPLACEMENT
1.Remove front seat assembly.
2. Remove the recliner cover.
3. Disconnect the scuff band.
4. Disconnect the connector (A), (B).

8.Disconnect the seat cushion pad (B) from the track (A).
9.After removing the hog- ring clips (A) on the front of seat cushion remove the seat cushion cover (B).
10. Installation is the reverse of removal.
a. To prevent wrinkles, make sure the material is stretched evenly over the cover (A) before securing the hogring
clips (B).
b. Replace the hogring clips with new ones using special tool (C).