reverse KIA CARNIVAL 2007 Workshop Manual

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
1.Disconnect the negative ( - ) battery terminal.
2. Remove the third, fourth seat (Refer to the Body group - seat)
3. Remove the D pillar and luggage side trim (Refer to the Body group - Interior trim).
4. Use a small screw driver to loosen clip (A). But do not remove power tailgate push rod (B).
5.Remove the power tail gate module mounting bolts (2EA) and connectors (2EA). And then remove the power tail
gate module (A).
TORQUE : 25- 35N.m(2.5- 3.5Kg.m)
6.Installation is the reverse of removal
a.Connect the connectors tightly.
b. Check the power tail gate for normal operation correctly.
a.A lost drive unit mounting bolt in the vehicle may make a noise.
b. Don't operate the power tail gate when a push rod is removed.
c. A learn cycle must be performed whenever the power is removed.
d. Check the normal operating whenever a power tailgate component is removed or replaced. If the chime
sound is heard, check the DTC, wiring harness and cable connections.

4.Remove the left and right side anti- pinch strip sensor (B) after removing the screws (5EA).
5.Installation is the reverse of removal. Part (C) has to be assembled using the cloth.

5.Remove the tail gate handle rod (A) and connector (B) from the cinching latch assembly (C).
6.Remove the latch mounting screws (3EA) and cinching latch assembly (A) from the tail gate.
7.Installation is the reverse of removal.
a.Check the power tail gate for normal operation.
b. Check the normal operating whenever a power tailgate component is removed or replaced. If the chime
sound is heard, check the DTC, wiring harness and cable connections.

3.Installation is the reverse of removal.
TAIL GATE SWITCH
1.Disconnect the negative ( - ) battery terminal.
2. Open the tail gate and remove the tail gate trim switch (A) using the appropriate trim tool. And then remove the
connector (B).
3.Installation is the reverse of removal.

2007 > 2.7L V6 GASOLINE >
OPERATION
FUNCTION OF SAFETY POWER WINDOW
When driver door power window auto - up switch is operated, safety function is activated. 1. Safety function condition
When the system detects a force of 100N during the window rising, window is reversed.
2. Length of window reversing (except when holding the auto - up switch)
a. When detect the jamming within 4mm ~ 300mm from top of the door.
→ Window is reversed until 350mm from top of the door.
b.When detect the jamming over the 300mm from top of the door.
→ Window is reversed until 50mm from jamming position.
3.Length of window reversing (holding the auto - up switch)
a. When detect the jamming during holding the auto - up switch.
→ Window is reversed until 20mm from jamming position.
4.Safety function is not available area
Safety function is not available within 4mm from top of the door.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
FRONT POWER WINDOW MOTOR
1. Remove ( - ) negative battery terminal.
2. Remove the front door trim panel. (Refer to the Body group - front door)
3. Remove the window motor (B) after disconnecting the motor connector (A) and mounting nuts.
4.Installation is the reverse of removal.
SLIDING POWER WINDOW MOTOR
1.Remove ( - ) negative battery terminal.
2. Remove the sliding door trim panel. (Refer to the Body group - rear door)
3. Remove the door trim seal and glass.
4. Remove the door regulator.
5. Remove the power window motor (A) after disconnecting the motor connector and power window motor mounting
nuts.
6.Installation is the reverse of removal.
QUARTER GLASS MOTOR
1.Remove ( - ) negative battery terminal.
2. Remove the D pillar trim panel (A). (Refer to the Body group - interior trim)

3.Remove the quarter glass motor (B) after disconnecting the motor connector (A) and quarter glass motor mounting
bolts and screws.
4.Installation is the reverse of removal.
INSPECTION
FRONT POWER WINDOW MOTOR INSPECTION
1. Remove ( - ) negative battery terminal.
2. Remove the rear door trim panel. (Refer to the Body group - front door)
3. Disconnect the motor connector from the motor.
4.Connect the motor terminals directly to battery voltage (12V) and check that the motor operates smoothly. Next,
reverse the polarity and check that the motor operates smoothly in the reverse direction. If the operation is
abnormal, replace the motor.
SLIDING POWER WINDOW MOTOR INSPECTION

1.Remove ( - ) negative battery terminal.
2. Remove the sliding door trim panel. (Refer to the Body group - rear door)
3. Disconnect the motor connector from the motor.
4.Connect the motor terminals directly to battery voltage and check that the motor operates smoothly. Next, reverse
the polarity and check that the motor operates smoothly in the reverse direction. If the operation is abnormal,
replace the motor.
QUARTER GLASS MOTOR INSPECTION
1.Remove ( - ) negative battery terminal.
2. Remove the D pillar trim panel (A). (Refer to the Body group - interior trim)
3. Disconnect the motor connector from the motor.
4.Connect the motor terminals directly to battery voltage and check that the motor operates smoothly. Next, reverse
the polarity and check that the motor operates smoothly in the reverse direction. If the operation is abnormal,
replace the motor.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
DRIVER/ASSIST DOOR MODULE (DDM/ADM)
1. Remove ( - ) negative battery terminal.
2. Remove the front door trim panel. (Refer to the Body group - front door)
3. Disconnect the door module mounting screws (5EA) after disconnecting the module connectors (3EA) from the
motor.
4.Remove the door module (DDM/ADM) (A) from the front door trim panel.
5.Installation is the reverse of removal.
SLIDING POWER WINDOW SWITCH
1.Remove ( - ) negative battery terminal.
2. Disconnect the connector (B) after removing the sliding power window switch (A) from the B pillar trim (C).
3.Installation is the reverse of removal.
QUARTER GLASS SWITCH

1.Remove ( - ) negative battery terminal.
2. Disconnect the connector (B) after removing the quarter glass switch (A) from the rear cargo area luggage trim.
3.Installation is the reverse of removal.