reverse KIA CARNIVAL 2007 Workshop Manual

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.Disconnect the negative ( - ) battery terminal.
2. Remove the console lower cover (A).
3.Remove the center facia panel(A) after loosening screws. Take care not to damage fixing clips.
4.Remove the windshield deicer switch from the center facia panel switch.
5.Installation is the reverse of removal.

2007 > 2.7L V6 GASOLINE >
INSPECTION
1.Disconnect the negative ( - ) battery terminal.
2. Remove the center facia panel, console lower cover and center air vent (A) after loosening screws. Take care not
to damage fixing clips.
3.Remove the center facia panel switch and air control panel (A) after loosening screws.
4.Disconnect the air control panel connector (A).
5.Installation is the reverse of removal.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
1.Remove the steering column upper and lower shrouds (A) after removing 3 screws.
2.Remove the wiper switch (A) by pushing the lock pin (B) after disconnecting the connector.
[LHD]
[RHD]
3.Installation is the reverse of removal.
INSPECTION
Check for continuity between the terminals while operating the wiper and washer switch. If it is not normal condition,
replace wiper and wiper switch.
[LHD]

2007 > 2.7L V6 GASOLINE >
REMOVAL
1.Remove the windshield wiper arm and blade after removing the mounting nut (A).
TORQUE: 28~32 Nm (2.8~3.2 kgf.m, 20~23.1 lbf.ft)
2.Remove the weather strip and the cowl top cover (A) after removing 4 fasteners.
3.Remove the windshield wiper motor and linkage assembly after removing 4 bolts. Disconnect the wiper motor
connector (A) and windshield deicer connector (B) from the wiper motor & linkage assembly.
Torque: 7 - 11Nm (0.7- 1.1, kgf.m, 5.0 - 7.9 lbf.ft)
4.Installation is the reverse of removal.
INSTALLATION
1.Install the wiper arm and blade to the specified position.
Specified position AB

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
1.Disconnect the negative ( - ) battery terminal.
2. Remove the front bumper cover. (Refer to Body group - Front bumper)
3. Remove the washer hose, the washer motor connector (A) and washer level sensor connector (C).
4. Remove the washer reservoir after removing 2 bolts and 1 step bolt.
5.Installation is the reverse of removal.
INSPECTION
1.With the washer motor connected to the reservoir tank, fill the reservoir tank with water.
2. Connect positive (+) battery cables to terminal 2 and negative ( - ) battery cables to terminal 1 respectively.
3. Check that the motor operates normally and the washer motor runs and water sprays from the front nozzles. If they
are abnormal, replace the washer motor.

5.Installation is the reverse of removal.
INSTALLATION
1.Install the rear wiper arm and blade to the specified position.
※ Specified position : The first defogger line from bottom of the rear window.
2. Set the rear washer nozzle on the specified spray position.
INSPECTION
1.Remove the 3P connector from the rear wiper motor.
2. Connect battery positive (+) and negative ( - ) cables to terminals 2 and 1 respectively.
3. Check that the motor operates normally. Replace the motor if it operates abnormally.

2007 > 2.7L V6 GASOLINE >
INSPECTION
Check it by the procedure below to see if the function of the ECM is normal.
1. Turn the ignition key to the "ON" position.
2. Cover the front sensor to stop functioning.
3. Shine a light at the rear sensor.
4. The ECM should be darkened as soon as the rear sensor detects the light.
If this test is performed in daytime, the mirror may be darkened as soon as the looking sensor is covered.
5. When the reverse gear is engaged, the ECM should not be darkened.
REPLACEMENT
1.Push the inside rear view mirror base down to remove the inside rear view mirror assembly (A) after removing the
mirror wire cover.
Take care not to damage the mounting bracket during removal.
2.Installation is the reverse of removal.

2007 > 2.7L V6 GASOLINE >
REPLACEMENT
GLASS REPLACEMENT
a. Put on glove to protect your hands.
1. Remove both decoration cover (A).
2.Remove the glass (A) by lifting it up.
a.Do not damage the roof panel.
3.Installation is the reverse of removal.
MOTOR REPLACEMENT

1.Remove the over head console.
a.Confirm the position of guide whether it is closed or not when you remove the motor.
2.Disconnect the motor connector (A), remove the screws and then remove the motor (B).
3.Installation is the reverse of removal.
a.Make sure to initialize the motor.
DEFLECTOR REPLACEMENT
1.Open the glass fully.
2. Disconnect the deflector link (A) from the frame (B) and then remove the deflector (C ).

3.Installation is the reverse of removal.
SUNROOF ASSEMBLY REPLACEMENT
1.Remove the follows parts.
a. Front and rear door scuff trim.
b. Center upper and lower pillar trim.
c. Headliner.
d. Sunroof glass.
2. Disconnect the drain tubes (A).
3. After loosening the mounting bolts and nuts, remove the sunroof assembly (B).
a.Take care not to scratch the interior trims and other parts.
4. Installation is the reverse of removal.