stop start Lancia Delta 2010 Owner handbook (in English)
[x] Cancel search | Manufacturer: LANCIA, Model Year: 2010, Model line: Delta, Model: Lancia Delta 2010Pages: 276, PDF Size: 5.31 MB
Page 129 of 276

128GETTING TO KNOW YOUR CAR
fig. 79L0E1016g
Identifying a parking space fig. 79
If the system identifies a suitable parking space between
two stationary vehicles or between other obstacles (e.g. ob-
jects with an extensive side surface such as vehicles, box-
es, etc.) it will signal that it has found a parking space that
can be entered. If the position reached is already suitable
at the beginning of the manoeuvre, the system will notify
the driver and engage reverse gear otherwise it will request
moving further forward.On the request to engage reverse gear the driver should sopt
the vehicle and engage reverse in order to confirm the wish
to start the manoeuvre; if the driver continues driving, af-
ter about 10 metres the system will no longer consider the
parking space identified and will start the search for an-
other suitable new space.
Manouevure
The driver will have control over the movements of the ve-
hicle using the accelerator, brake and clutch (only on ver-
sions with manual transmission) whilst the system will au-
tomatically manage the steering to enter the parking space
identified in the best possible way.
During the manoeuvre it will be possible to take advantage
of the information coming from the parking sensors (when
reversing it is advisable to reach the area where the rear
sensors provide a continuous tone signal), but it is always
advisable to keep an eye on the surrounding area.
The vehicle can be stopped during the manoeuvre and,
whilst remaining stationary, reverse gear can temporarily
be released (for example, to allow a pedestrian to go by in
the area of the manoeuvre).
The speed should be less than about 7 km/h during the
manoeuvre, otherwise the parking manoeuvre will be in-
terrupted.
001-142 Delta 3ed gb 30-11-2009 11:22 Pagina 128
Page 132 of 276

GETTING TO KNOW YOUR CAR131
1MESSAGES FROM THE SYSTEM IN THE INSTRUMENT PANEL
The Magic Parking system is
searching for a suitable parking
space.
The Magic Parking system is
searching for a suitable parking
space.
The Magic Parking system is
searching for a suitable parking
space.
A suitable parking space has
been identified and the position
is correct for starting the parking
manoeuvre. It is necessary to
stop and engage reverse gear.
Disengage
reverse
gearWhen the Magic Parking activation
button is pressed, reverse gear must
be released for the system to be
switched on.
Don’t touch
steer. wheel!The manoeuvre is about to commence,
the driver is invited to let go of the
steering wheel.
Don’t touch
steer. wheel!
Do the
manoeuvreThe manoeuvre has started, the driver
can accelerate and release the clutch
(in the case of a manual transmission)
to enter the parking space; the Magic
Parking system will manage the steer-
ing automatically.
Too fast!The speed of the vehicle is about to ex-
ceed the maximum speed permitted by
the system (the message will be dis-
played at about 25 km/h for the
search stage), if the driver increases
the speed further, the system will au-
tomatically be deactivated.
IMPORTANT Some text messages displayed by the instrument panel are accompanied by acoustic warnings
001-142 Delta 3ed gb 30-11-2009 11:22 Pagina 131
Page 135 of 276

134GETTING TO KNOW YOUR CAR
fig. 82L0E0249m
The ultimate responsibility when parking
and carrying out other dangerous manoeu-
vres still rests with the driver. When parking, make
sure that no-one is standing in the area, especially
children or animals. Parking sensors are designed
to assist drivers: in all cases, you must always pay
the utmost attention during potentially dangerous
manoeuvres, even when carried out at low speed.
Version with 8 sensors
On the version with 4 front sensors and 4 rear sensors, the
system is activated when reverse gear is engaged or by
pressing the button fig. 8. If there has been a request to
activate the Magic Parking system, the front and rear sen-
sors are not automatically activated during the search for
a parking space, but can be activated by pressing the spe-
cial button (fig. 82) or by engaging reverse gear when
the speed is below around 15 km/h.
When reverse gear is released, the front and rear sensors
remain activated until a speed of around 15 km/h is ex-
ceeded to allow the parking manoeuvre to be completed.
The system can also be activated by pressing the button
fig. 82 in the centre panel: a warning light in the button
comes on when the system is activated.
The sensors are deactivated by pressing the button again
fig. 82 or when a speed of 15 km/h is exceeded: the warn-ing light in the button remains off when the system is not
activated.
When the sensors are activated, the system starts to pro-
duce acoustic signals from the front or rear buzzers as soon
as an obstacle is detected with the frequency increasing as
the obstacle gets closer.
When the obstacle is less than about 30 cm away, the
sound becomes continuous. Depending on the position of
the obstacle (in front or behind) the sound is produced by
the corresponding buzzers (front or rear). The obstacle
closest to the vehicle is signalled.
The acoustic signal stops immediately if the distance of
the obstacle increases. The sound cycle remains constant
if the distance measured by the centre sensors remains un-
changed, whilst if this situation occurs for the side sen-
sors, the signal is interrupted after about 3 seconds (for
example, to prevent signals in the case of manoeuvres
alongside walls).
001-142 Delta 3ed gb 30-11-2009 11:22 Pagina 134
Page 168 of 276

STARTING UP AND DRIVING167
3
STARTING PROCEDURE FOR PETROL
VERSIONS
Proceed as follows:
❍engage the handbrake;
❍put the gear lever into neutral;
❍press the clutch pedal down to the floor without touch-
ing the accelerator;
❍turn the ignition key to AVV and release it the moment
the engine starts.
If the engine does not start at the first attempt, return
the ignition key to STOP before repeating the procedure.
If, when the ignition key is at MAR the
Ywarning light
remains lit together with warning light U, turn the key
to STOP and then back to MAR; if the warning light re-
mains lit, try with the other keys provided with the car.
Contact a Lancia Dealership if you still cannot start the
engine.
PROCEDURE FOR DIESEL VERSIONS
Proceed as follows:
❍engage the handbrake;
❍put the gear lever into neutral;
❍turn the ignition key to MAR: instrument panel warn-
ing lights
mandYwill light up;
❍wait for warning lights
Yandm, to turn off. The
hotter the engine is, the quicker this will happen;❍press the clutch pedal down to the floor without touch-
ing the accelerator;
❍turn the ignition key to AVV as soon as the
mwarn-
ing light goes out. Waiting too long will waste the work
done by the glow plugs.
Release the key as soon as the engine starts.
IMPORTANT When the engine is cold, the accelerator
pedal must be completely released when the key is turned
to AVV.
If the engine does not start at the first attempt, return the
ignition key to STOP before repeating the procedure. If,
when the ignition key is at MAR the
Ywarning light re-
mains lit, turn the key to STOP and then back to MAR; if
the warning light remains lit, try with the other keys pro-
vided with the car. Contact a Lancia Dealership if you still
cannot start the engine.
Warning light mwill blink for 60 seconds
after starting or during prolonged cranking
to indicate a fault in the glow plug preheat-
ing system. Use the car normally if the engine starts
and contact the Lancia Dealership as soon as pos-
sible.
165-174 Delta 3ed gb 11-11-2009 12:10 Pagina 167
Page 169 of 276

168STARTING UP AND DRIVING
Never jump start the engine by pushing, tow-
ing or driving downhill. This could cause a
flow of fuel into the catalytic converter and
damage it beyond repair.
HOW TO WARM UP THE ENGINE AFTER
IT HAS JUST STARTED
Proceed as follows:
❍drive off slowly, letting the engine turn at medium
speed. Do not accelerate abruptly;
❍do not demand maximum performance for the first few
kilometres. Wait until the engine coolant gauge starts
moving.
STOPPING THE ENGINE
Turn the ignition key to STOP while the engine is idling.
IMPORTANT After a taxing drive, you should allow the
engine to “catch its breath” before turning it off by letting
it idle to allow the temperature in the engine compartment
to fall.
A quick burst on the accelerator before turn-
ing off the engine serves absolutely no prac-
tical purpose, it wastes fuel and is damaging
especially to turbocharged engines.
HANDBRAKE
The handbrake lever is located between the two front seats.
Pull the lever upwards to operate the handbrake.
The car should be braked after a few snaps
of the lever, if it is not, contact a Lancia Deal-
ership to have it adjusted.
When the handbrake lever is engaged and the ignition key
is on MAR, the instrument panel warning light xwill
light.
Proceed as follows to release the handbrake:
❍slightly lift the handbrake and press release button
A-fig. 1;
❍hold button A pressed and lower the lever. The x
warning light on the instrument panel will go out.
Press the brake pedal when carrying out this operation
to prevent the car from moving accidentally.
165-174 Delta 3ed gb 11-11-2009 12:10 Pagina 168
Page 170 of 276

STARTING UP AND DRIVING169
3
PARKING THE CAR
Proceed as follows:
❍stop the engine and engage the handbrake;
❍engage a gear (on a slope, engage first gear if the car
is faced uphill or reverse if it is faced downhill) and
leave the wheels steered.
If the car is parked on a steep slope, it is further advisable
to block the wheels with a wedge or stone.
Do not leave the ignition key on MAR to prevent drain-
ing the battery. Always remove the key when you leave the
car.
Never leave children unattended in the car. Always remove
the ignition key when leaving the car and take it out with
you.
fig. 1L0E0072m
USING THE MANUAL GEARBOX
To engage the gears, press the clutch pedal fully and shift
the gear lever into one of the required positions (the gear
diagram varies according to the different versions and is
shown on the knob or on the plate below the lever fig. 2).
To engage sixth gear, operate the lever by pressing it to-
wards the right in order to avoid engaging fourth gear by
mistake. Use the same action to pass from sixth to fifth
gear.
IMPORTANT Reverse may only be engaged when the car
is at a standstill. With the engine running, wait at least 2
seconds before engaging reverse gear with the clutch
pressed down to the floor in order to avoid damaging or
scraping the gears.
fig. 2L0E0073m
165-174 Delta 3ed gb 11-11-2009 12:10 Pagina 169
Page 172 of 276

STARTING UP AND DRIVING171
3
Accessories fitted on longitudinal bars
Remove any accessories such as: longitudinal bars, ski
racks, luggage rack, from the roof if they are not being
used. These accessories decrease aerodynamic penetration
and have a negative effect on fuel consumption. It is bet-
ter to use a trailer to transport particularly bulky objects.
Electrical devices
Use electrical devices only for the amount of time needed.
The heated rear windscreen, additional headlights, wind-
screen wipers and heater fan need a considerable amount
of energy; increasing the requirement of current increas-
es fuel consumption (up to +25% in the urban cycle).
Climate control
The climate control system leads to higher fuel consump-
tion (up to +20% on average): use air vents only when the
external temperature allows.
Spoilers
The use of non-certified aerodynamic items may adversely
affect air drag and fuel consumption levels.DRIVING STYLE
Starting
Do not warm the engine up with the car standing: the en-
gine warms up very slowly in these conditions, increas-
ing fuel consumption and emissions. It is advisable to start
off immediately and slowly keeping the engine speed
down: the engine will warm up much faster this way.
Unnecessary actions
Avoid revving up when starting at traffic lights or before
stopping the engine. The latter action, like doubling the
clutch, is unnecessary and causes increased fuel con-
sumption and pollution.
Gear selection
Use a higher gear as soon as traffic and road conditions
allow. Using a low gear for faster acceleration will increase
fuel consumption.
In the same way improper use of a high gear increases
fuel consumption, emissions and engine wear.
Top speed
Fuel consumption considerably increases as speed in-
creases. Keep your speed as even as possible, avoiding un-
necessary braking and acceleration, which cause excessive
fuel consumption and increased emissions.
165-174 Delta 3ed gb 11-11-2009 12:10 Pagina 171
Page 215 of 276

214IN AN EMERGENCY
TOWING THE CAR
The tow ring provided with the car is housed in the tool
box under the luggage compartment mat.
FASTENING THE TOW RING fig. 43-44
Proceed as follows:
❍release cap A;
❍take the tow hook B from its seat in the tool support;
❍tighten the ring on the rear or front threaded pin.
fig. 43L0E0090mfig. 44L0E0091m
Before starting towing operations, turn the ig-
nition key to MAR and then to STOP, without
extracting it. If the key is extracted, the steer-
ing wheel lock will be automatically activated, thus
preventing steering. The power brakes and the elec-
trical power steering will not work while the car is be-
ing towed. More effort on the brake pedal and steer-
ing wheel will therefore be required. Do not use wires
for towing. Do not jerk. Make sure not to damage parts
in contact with the car while towing. Respect the spe-
cific rules of the Highway Code when towing the car
specifically in relation to the towing device and the be-
haviour to maintain on the road. Do not start the en-
gine while towing the car.
175-214 Delta 4ed gb 24-02-2010 14:36 Pagina 214
Page 235 of 276

234CARE AND MAINTENANCE
WHEELS AND TYRES
Check the pressure of each tyre, including the spare wheel,
approximately once every two weeks and before starting
a long journey: this check must be performed with the tyre
rested and cold.
It is normal for the pressure to increase when the car is
used; for the correct tyre inflation pressure, see “Wheels”
in chapter “6”.
Incorrect tyre pressure causes abnormal tyre wear fig. 4:
A normal pressure: evenly worn tread;
B low pressure: tread particularly worn on the edges;
C excessive pressure: tread particularly worn in the mid-
dle.
fig. 4L0E0096m
The tyres must be replaced when the tread is less than 1.6
mm thick. In all cases, follow the laws in force in the coun-
try where you are driving.
IMPORTANT NOTES
❍Avoid braking suddenly, burning starts and violent
knocks against the curb, potholes or other obstacles
where possible. Long distances on rough roads may
damage the tyres;
❍check the tyres regularly for cuts on the sides, swelling
or irregular tread wear. Go to a Lancia Dealership if
required;
❍do not overload your car: this may cause serious dam-
age to wheels and tyres;
❍if a tyre is punctured, stop immediately and change it
to avoid damage to the tyre, wheel rim, suspension and
steering system;
215-242 Delta 3ed gb 11-11-2009 12:14 Pagina 234