lock Lancia Thesis 2007 Owner handbook (in English)

ASR SYSTEM (wheel antiskid system)
Warning light/symbol
V
Message
ASR OFF
ASR ON
SYSTEM
UNAVAILABLEMeaning of the message
System has been deactivated
manually
System has been activated
manually
System setting in progressAction
–
–
–
EBD SYSTEM (electronic brakeforce distributor)
Warning light/symbol
x>
Message
EBD SYSTEM FAULT
SWITCH OFF ENGINE,
DO NOT PROCEED
SYSTEM
UNAVAILABLEMeaning of the message
EBD system failure
System setting in progressAction
Stop the car and contact a
Lancia Dealership
The car is fitted with an
electronic brakeforce
distributor (EBD). The
turning on at the same time of
the
xand >warning lights on
the instrument panel together
with message “EBD SYSTEM
FAULT” on the multifunction
display, with engine running,
indicates and EBD system fail-
ure; in this case heavy braking
may cause the rear wheel lock
before time, with the possibility
of skidding.
–
129

148
FRONT CONTROL PANEL (fig. 121)
fig. 121L0A0054b
INITIALISING THE AIR
CONDITIONING CONTROL UNIT
Whenever the battery is electrically
connected again or it is reloaded
after being completely flat or after
replacing one of the protection fuses,
to restore the correct operation of
the air conditioning, of the door
locking and of the ESP system. It is
necessary to perform the initialisa-
tion operations contained in the
paragraph “If battery is to be dis-
connected” in the chapter “In an
emergency”.

172
INSTRUMENT
DIMMER (fig. 127)
Turn ring Aupwards or downwards
when the outside lights are on to re-
spectively decrease or increase instru-
ment brightness.HEATED REAR WINDOW
(fig. 128)
Press button Ato switch the heated
rear window on/off. The led on the
button will come on.
The heated rear window will be au-
tomatically switched off after about
20 minutes.
The electrical rearview mirror
demister will also be switched on au-
tomatically.
fig. 127
L0A0202b
fig. 128
L0A0198b
FUEL CUT-OFF SWITCH AND
CIRCUIT BREAKER
The car is fitted with two safety
switches that come into operation in
the case of an accident to block fuel
supply and power, thereby stopping
the engine and the car electric utili-
ties. It also prevents fuel spilling if the
lines are broken in the accident or
sparks and flashover due to electric
component damages.
After the crash, remember to turn
the ignition key to STOPto prevent
the battery running down.

173
If, after an accident, you
can smell petrol or see
that the fuel feed system is
leaking, do not reset the switches
to avoid the risk of fire.Mechanical connections
of outside handles are
active only if the doors
are locked. In case the driver has
activated the central door locking
from the inside and, after an
accident, the inertial switch was
not able to activate the automatic
door unlocking as a result of bat-
tery loss or damage, it will not be
possible to reach the passenger
compartment from the outside.Anyway, door opening
from the outside depends
on their conditions after
the accident: if a door is distorted
it might be impossible to open it
even if it is unlocked. In this case
try to open the other car doors.
Before resetting the fuel
cut-off switch, carefully
check for any fuel leaks or
damages to the car electric devices
(e.g.: headlights).
fig. 129
L0A0273b
If, after an accident, you cannot see
any fuel leaks or damages to the car
electric devices (e.g.: headlights) and
the car is in a fit state to continue its
journey, reset the fuel cut-off switch
and the circuit breaker according to
the following instructions.
Door unlocking in case of
accident
In case of accident with activation of
the inertial switch as a consequence,
door locks are automatically unlocked
to let rescuers reach the passenger
compartment from the outside.Resetting the fuel cut-off switch
(fig. 129)
fig. 130
L0A0030b

174
Lift cover Aset at the driver's left
and press button Bto reset the fuel
cut-off switch.
Resetting the circuit breaker
Before resetting the cir-
cuit breaker, carefully
check for any fuel leaks or
damages to the car electric devices
(e.g.: headlights).Circuit breaker is located on the left
side of the boot, inside a box directly
set and connected to the battery pos-
itive terminal.
To reach the circuit breaker:
1) Open the tailgate.
2) Loosen knob A(fig. 130) and re-
move the battery cover B.
3) Press tabs A(fig. 131) and re-
move cover B.
4) Press button A(fig. 132) to reset
the circuit breaker.Initialising the control units of
the door locks, air conditioner
and ESP system
After resetting the circuit breaker, to
restore correct door locking, air con-
ditioning and ESP system, perform
the following operations:
1) Close the doors and the tailgate,
fit the key into the lock of one of the
front doors and perform a door cen-
tralised opening/closing cycle.
2) Start the engine and turn on the
compressor of the conditioner, setting
a lower temperature value than that
of the environment and check
whether the led on the disconnection
push button of the conditioner com-
pressor òis lit.
3) Turn the steering wheel one
fourth turn at least (the car can be at
standstill but the engine shall be run-
ning) and start running the car for a
few metres in a straight line until the
ESP warning light
áis off.
fig. 131
L0A0031b
fig. 132
L0A0347b

ELECTRIC PARKING BRAKE
(EPB) (fig. 133)
The car is fitted with the EPB
(Electric Parking Brake) that cuts in
when switching the engine off and
will cut out when starting the engine
and pressing the accelerator pedal
(for manual gearbox versions when
releasing the clutch pedal at the
same time). The EPB can also be
disengaged manually by pressing
button Aset on the central console
with engine running or ignition key
to MAR.
After disengaging the EPB manual-
ly, when opening the driver’s door
the EPB will re-engage automatical-
ly, press button Aagain to disengage
it.The button shape is rather large so
the brake can be engaged rapidly,
even by the passenger, in case of
emergency.
The advantages of this system, com-
pared to the usual lever, are several:
– no effort should be made to
engage and disengage the parking
brake
– the parking brake efficiency is
always at top level in any using con-
dition, contrary to the lever which
guarantees the car complete stop only
when fully lifted
– the EPB is controlled by electric
wires, therefore all problems regard-
ing transmission cables, such as
adjustments, freezing or tears, no
longer exist
– improved safety as a result of the
sophisticated electronic control sys-
tem, similar to the ABS one, prevent-
ing wheels from blocking if the park-
ing brake is engaged during driving
– improved safety when the car is
stationary and children are left
inside the car; in this case the brake
cannot be disengaged if the ignition
key is at STOPor removed– it has automatic functions that
other systems lack.
When the parking brake is engaged
and the ignition key is at MAR, the
instrument panel warning light x
turns on.
This warning light turns on when
the parking brake reaches its highest
working level, and it turns off when
the brake is disengaged and com-
pletely released. Unlike usual park-
ing brakes, whose warning light
turns on even when the lever is lift-
ed a little bit, the EPB system warn-
ing light turns on only when the car
has come to a complete stop.
When the brake is engaged, a typi-
cal noise can be heard by the driver;
the parking brake is completely
engaged or disengaged when the
operating noise stops.
fig. 133
L0A0197b
When engaging the park-
ing brake keep the brake
pedal always depressed.
175

177
“Automatic parking brake” function
and the press “OK”. Deactivation of
automatic operation can be achieved
also in the following way:
– turn the key to STOP(the park-
ing brake is engaged)
– turn the key back to MAR,
depress the brake pedal and at the
same time keep button Apressed for
at least 2 seconds. Warning light x
flashes thrice to indicate the auto-
matic operation deactivation.
When the key is turned again to
STOPthe parking brake will not be
engaged. The parking brake auto-
matic operation will be automatical-
ly restored when the key is turned
again to MAR.IMPORTANTIf, after the parking
brake has been disengaged, the car
starts moving at a speed higher than
the usual manual movement, deacti-
vation of the automatic mode is
immediately cancelled and the park-
ing brake is engaged.
If, after the parking
brake has been disen-
gaged, the car starts mov-
ing at a speed higher than the
usual manual movement, deacti-
vation of the automatic mode is
immediately cancelled and the
parking brake is engaged.Proceed as follows: release the
accelerator pedal, press and keep
button A(fig. 133) pressed for the
whole manoeuvre: the system elec-
tronic control unit will come imme-
diately into action with alternate
braking on/off cycles on the rear
wheels (thus preventing wheel lock-
ing). Braking cycles are applied
alternately on right and left wheel to
guarantee roadholding, braking
continuity and to reduce braking
distance.
Wheel locking could take place
under the safety speed threshold
(lower than 10 km/h).
A buzzer will sound during the
whole manoeuvre to indicate that
the dynamic mode shall only be used
in an emergency, but this is also use-
ful to warn the driver if the parking
brake has been inadvertently
engaged by other passengers.
Use in an emergency
In particular cases (e.g. fault in the
whole hydraulic brake system, both
service and emergency brake), the
parking brake can be used to stop
the car running (“dynamic mode”).

179
The car is fitted also with an emer-
gency button A(fig. 134), placed in
the boot right compartment, which
can be used to unblock the car if it has
been stopped on the road for a break-
down or an accident and the key can-
not be turned to MAR(accident with
fire risk). To reach the button remove
the compartment cover turning the
catch A(fig. 135) to 1with the igni-
tion key.
To disengage the parking brake
through the emergency button pro-
ceed as follows:
– press and release the main button
on the central console
– press and release the emergency
button in the boot
– press again and release the main
button on the central console.
The time elapsed between these
operations should be lower than 30
seconds.MANUAL GEARBOX
To engage the gears, press down
the clutch and put the gear lever into
one of the positions shown in the
diagram (fig. 136); the diagram is
also on the gear lever knob.
To engage reverse (R), wait for the
car to come to a standstill and lift
the ring Aunder the knob (with the
fingers of the hand operating the
lever).
Release the ring after engaging
reverse gear. You do not need to lift
the ring to disengage reverse.To change gear properly
you must push the clutch
pedal fully down. It is
therefore essential that there is
nothing under the pedals: make
sure mats are lying flat and do
not get in the way of the pedals.
Reverse can only be
engaged when the car is at
a standstill. Wait for two
seconds or longer with the clutch
fully pressed before engaging
reverse when the engine is run-
ning to prevent scraping and
damaging the gears.
Do not drive with your
hand resting on the gear
stick as the force exerted,
even if only slight, could lead to
premature wearing of the gear-
box internal components.
fig. 136
L0A0357b

180
ELECTRONIC
AUTOMATIC
GEARBOX
(COMFORTRONIC)
The electronic automatic gearbox,
besides the usual provided opera-
tions, enables a manual operation
sequential gear selection by shifting
the related lever into the special sec-
tor.
IMPORTANTIn order to use the
automatic gearbox in the right way
it is necessary to read this paragraph
fully, to learn from the very begin-
ning how to perform correct opera-
tions, also on the basis of the Shift-
lock and Key-lock functions the
automatic gearbox is fitted with.STARTING THE ENGINE
The engine can be started only with
the selector to Por N (fig. 137).
For safety reasons, it is advisable to
start the engine with the brake pedal
pressed.
IMPORTANTAt the moment of
departure, after starting the engine,
do not press the accelerator pedal
before and during the gear lever
shift. Observing this precaution is
particularly important when the
engine is cold.MOVING OFF
After starting the engine at idle and
while keeping the brake pedal
pressed (Shift-lock safety), shift the
gear lever to D, or to the manual
sequential operation position.
Release the brake pedal and press
gradually the accelerator pedal.
IMPORTANTThe lever shift from
Pis possible only if the ignition key
is at MARand the brake pedal is
depressed (Shift-lock safety).
The gear lever can be shifted freely
from position Dto other positions
without pressing the brake pedal,
according to the diagram shown on
the mask. Only when shifting from
position Pit is necessary, for safety
reasons, to press the brake pedal to
move the lever.
fig. 137
L0A0184b

181
Do not tax the engine
until it has not reached
operating temperature.
STOPPING THE CAR
To stop the car press the brake
pedal, regardless of the gear lever
position.
If the brake pedal is not
pressed, when the gear
lever is to D or R and the
engine is running idle, even on a
flat ground, the car starts moving.The ignition key can be extracted
from the ignition switch only when
the gear lever is at P(Key-lock safe-
ty) and the ignition key is at STOP.
Letter Pon the instrument panel
display (fig. 138) will come on for
30 seconds, then it will go off.IMPORTANTIn case of emer-
gency (failures, flat battery, etc.), it
is possible to remove the ignition key
even if the gear lever is not at P. To
do this, turn the key to STOP, press
button A(fig. 139) and at the same
time remove the key.
fig. 138
L0A0238b
fig. 139
L0A0178b