LAND ROVER DEFENDER 1996 Workshop Manual

51REAR AXLE AND FINAL DRIVE
2
DESCRIPTION AND OPERATION
Rear axle hub - 110/130
1.Axle casing
2.Ventilation pipe
3.Axle shaft
4.Wheel studs and hub
5.Wheel bearing stub axle
6.Wheel bearings
7.Inner hub seal8.Outer hub/axle shaft seal
9.Hub lock plate, thrust washer and nuts
10.Brake disc
11.Drive flange
12.Drive shaft circlip
13.Dust cap

REAR AXLE AND FINAL DRIVE
1
FAULT DIAGNOSIS FAULT DIAGNOSIS
Complaint - Oil leaks
An external leak of lubrication from the hub seals can
be caused by a faulty internal seal. For example, if the
seals which separate the differential from the hubs are
faulty and the vehicle is operating or parked on an
embankment, oil from the differential may flood one
hub resulting in a lack of lubrication in the differential.
When a seal is found to be leaking check the axle
ventilation system, as a blockage can cause internal
pressure to force oil past the seals.
See 'Description and Operation' for illustrations of oil
seal locations.
When investigating hub seal leaks check the grease
for dilution with oil. Also check the differential oil level,
for signs of metal particles in the oil and the condition
of internal seals.
If the vehicle is driven in deep water with defective oil
seals, water may contaminate the lubricants and raise
the differential oil level, giving a false impression that
the housing has been overfilled.
Do not assume that a high oil level in the
differential is due to over filling or, that a low level
is because of an external leak.

REAR AXLE AND FINAL DRIVE
1
REPAIR REAR AXLE
Service repair no - 51.25.01
Remove
WARNING: Remove and refit of axle
requires a further two persons to steady
the axle when lowering or repositioning
axle.
1.Drain brake system.
2.Support chassis rear.
3.Remove road wheels.
4.Support axle weight with hydraulic jack.
5.Disconnect shock absorbers.
6.Disconnect flexible brake hose at RH chassis
side member and breather hose at banjo
connection on axle casing.
7.Disconnect lower links at axle.8.Mark differential and propeller shaft flanges with
identification marks for assembly.
9.Remove 4 nuts and bolts, lower propeller shaft
and tie to one side.
10.Disconnect pivot bracket ball joint at axle
bracket.
11.Release bolts and remove coil spring retaining
plates.
12.Lower axle and remove road springs.
13.If applicable, remove anti-roll bar links at axle
See REAR SUSPENSION, Repair, anti-roll
bar
.
14.Remove axle assembly.

51REAR AXLE AND FINAL DRIVE
2
REPAIRREV: 05/99 Refit
15.Position axle and fit lower links. Tighten fixings
to
176 Nm (130 lbf/ft).
16.If applicable, fit anti-roll bar links to axleSee
REAR SUSPENSION, Repair, Anti-roll bar
links
.
17.Raise axle and locate road springs.
18.Fit coil spring retaining plates and secure with
fixing bolts.
19.Secure pivot bracket ball joint to axle bracket.
Tighten fixing to
176 Nm (130 lbf/ft).
20.Align propeller shaft to differential drive flange
and tighten fixings to
47 Nm (35 lbf/ft).
21.Reconnect flexible brake hose and axle breather
hose.
22.Refit shock absorbers.
23.Fit road wheels and tighten to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy Duty wheels -170 Nm (125 lbf/ft)
24.Remove rear chassis support.
25.Bleed brake system
See BRAKES, Repair,
brake system bleed
.

REAR AXLE AND FINAL DRIVE
3
REPAIR REAR HUB ASSEMBLY - 90
Service repair no - 64.15.01
Remove
1.Place rear axle onto axle stands and remove
road wheel.
2.Release brake hose clips and remove brake
caliper bolts. Secure to one side.
WARNING: Take care not to kink brake
hose.
3.Remove 5 bolts and withdraw axle shaft.
4.Remove joint washer.
5.Bend back lock washer tabs.
6.Remove locknut and lock washer.
7.Remove hub adjusting nut.
8.Remove spacing washer.
9.Remove hub and brake disc assembly complete
with bearings.
Rear hub components - 90
1.Axle shaft.
2.Axle shaft joint washer.
3.Axle shaft retaining bolt.
4.Lock nut.
5.Lock washer.
6.Hub adjusting nut.
7.Spacing washer.8.Outer bearing.
9.Hub.
10.Inner bearing.
11.Grease seal.
12.Brake disc.
13.Disc retaining bolt.

51REAR AXLE AND FINAL DRIVE
4
REPAIRREV: 05/99 Refit
10.Clean stub axle.
11.Fit hub assembly to stub axle.
12.Fit spacing washer.
13.Fit hub adjusting nut. Tighten to
50 Nm (37
lbf/ft).
Ensure hub is free to rotate with no
bearing play. Back off adjusting nut 90°and
tighten to
10 Nm (7 lbf/ft).
14.Fit a new lock washer.
15.Fit locknut. Tighten to
50 Nm (37 lbf/ft).
16.Tab over lock washer to secure adjusting nut
and locknut.
17.Using a new joint washer fit axle shaft to hub.
Tighten bolts to
65 Nm (48 lbf/ft).
18.Fit brake caliper. Tighten bolts to82 Nm (61
lbf/ft).
Secure brake pipes to axle casing.
19.Fit road wheel, remove axle stands and tighten
road wheel nuts to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)
20.Operate footbrake to locate brake pads before
driving vehicle.

REAR AXLE AND FINAL DRIVE
5
REPAIR REAR HUB ASSEMBLY - 110/130
Service repair no - 64.15.01
Remove
1.Loosen rear wheel nuts, jack up vehicle and
lower onto axle stands. Remove road wheel.
2.Release brake pipe clips, remove brake caliper
and brake disc shield bolts. Secure to one side.
WARNING: Take care not to kink brake
hose.3.Lever off dust cap.
4.Remove circlip from driveshaft.
5.Remove 5 bolts and withdraw driving member
and joint washer.
6.Bend back lock washer tabs.
7.Remove locknut and lock washer.
8.Remove hub adjusting nut.
9.Remove spacing washer.
10.Remove hub and brake disc assembly complete
with bearings.
Hub components
1.Dust cap.
2.Drive shaft circlip.
3.Drive member.
4.Drive member joint washer.
5.Drive member retaining bolt.
6.Lock nut.
7.Lock washer.
8.Hub adjusting nut.9.Spacing washer.
10.Outer bearing.
11.Hub.
12.Inner bearing.
13.Grease seal.
14.Brake disc
15.Disc retaining bolt.

51REAR AXLE AND FINAL DRIVE
6
REPAIRREV: 05/99 Refit
11.Clean stub axle and drive shaft and fit hub
assembly to axle.
12.Fit spacing washer.
13.Fit hub adjusting nut. Tighten to
50 Nm (37
lbf/ft).
Ensure hub is free to rotate with no
bearing play.
14.Back off adjusting nut 90°and tighten to
10 Nm
(7 lbf/ft).
15.Fit a new lock washer.
16.Fit locknut. Tighten to
50 Nm (37 lbf/ft).
17.Tab over lock washer to secure adjusting nut
and locknut.
18.Fit a new joint washer to driving member and fit
member to hub. Tighten bolts to
65 Nm (48
lbf/ft).
19.Fit circlip and dust cap.
20.Fit brake disc shield and brake caliper. Tighten
bolts to
82 Nm (61 lbf/ft).
21.Bleed brake systemSee BRAKES, Repair,
Brake system bleed
.
22.Fit road wheel, remove axle stands and tighten
road wheel nuts to correct torque:
Alloy wheels -
130 Nm (96 lbf/ft)
Steel wheels -100 Nm (80 lbf/ft)
Heavy duty wheels -170 Nm (125 lbf/ft)
23.Operate footbrake to locate brake pads before
driving vehicle.

REAR AXLE AND FINAL DRIVE
7
REPAIR DIFFERENTIAL ASSEMBLY - 90
Service repair no - 51.15.01
Remove
1.Using suitable container, drain axle oil.
2.Mark differential and propeller shaft flanges to
facilitate reassembly.
3.Remove 4 bolts and disconnect propeller shaft
from differential. Tie aside.
4.Remove 5 hub drive member bolts and withdraw
axle half shafts sufficiently to disengage from
differential unit.
5.Remove 10 nuts securing differential to axle
case.
6.Withdraw differential unit.
NOTE: The differential unit can only be
serviced as a complete assembly with
matching drive pinion. For advice ring
Land Rover Service Department.Refit
7.Ensure mating faces are clean and apply a bead
of RTV sealant to axle case.
8.Support differential unit and position on axle
casing.
9.Secure with self locking nuts and tighten to
40
Nm (30lbf/ft).
10.Align marks on flanges and secure propeller
shaft to differential. Tighten bolts to
48 Nm (35
lbf/ft).
11.Refit half shafts, using new drive member
gaskets. Tighten bolts to
65 Nm (48 lbf/ft).
12.Refill axle oil with approved lubricantSee
LUBRICANTS, FLUIDS AND CAPACITIES,
Information, Recommended lubricants and
fluids
.

REAR AXLE AND FINAL DRIVE
1
OVERHAUL DIFFERENTIAL ASSEMBLY - 110/130
Service repair no - 51.15.07
Overhaul
1.Drain off differential lubricating oil, and refit plug.
2.Remove rear axle assembly from vehicle
See
Repair, Rear axle
3.Remove hub driving member fixings.
4.Withdraw driving member and axle shaft
sufficiently to disengage differential.
5.Repeat instruction 4 for other axle shaft.
6.Remove fixings and support strip at differential
cover and withdraw cover and joint washer.
7.Note relationship marking on bearing caps and
axle casing to ensure correct refitting.
8.Remove fixings and withdraw differential bearing
caps.
9.Clean out and examine spreader tool pegholes
provided in gear casing face; ensure that holes
are free from dirt and burrs and damage.
10.Ensure that turnbuckle adjuster is free to turn.
Using axle spreader 18G31C
11.Fit axle spreader to engage peg holes.
(Spreader18G131C, Adaptor pegs18G131F)
12.Using a spanner, turn adjuster until all free play
between spreader and casing is taken up,
denoted by adjuster becoming stiff to turn.
13.Check that side members of spreader are clear
of casing.
14.Stretch casing, rotating adjuster by one flat at a
time, until differential assembly can be levered
out. Do not lever against spreader; use suitable
packing under levers to avoid damage to casing.