LAND ROVER DEFENDER 1999 Owner's Manual
Manufacturer: LAND ROVER, Model Year: 1999, Model line: DEFENDER, Model: LAND ROVER DEFENDER 1999Pages: 667, PDF Size: 8.76 MB
Page 21 of 667
01INTRODUCTION
14
INFORMATION READING THIS SUPPLEMENT
This Supplement is divided into sections shown on the
contents page, alongside a range of icons, familiar to
service technicians.
Relevant information is contained within each of these
sections. These are further divided into the following
sub-sections which appear at the foot of each page :-
Description and operation.
Adjustment.
Repair.
Overhaul.
To avoid repeating information through the sections,
where part of the repair operation impacts on another
section, a cross reference is given to direct the reader
to where the information is sited.
For example:
The maintenance section states the need to renew
drive belt. A cross reference sites this information in:
Section 12 Engine
- Sub-section: Repair
ProCarManuals.com
Page 22 of 667
04 - GENERAL SPECIFICATION DATA
CONTENTS
Page
INFORMATION
ENGINE - Td5 1......................................................................................................
FUEL SYSTEM - Td5 3...........................................................................................
COOLING SYSTEM - Td5 3....................................................................................
CLUTCH - Td5 3.....................................................................................................
TRANSMISSION - Td5 4.........................................................................................
STEERING 5...........................................................................................................
SUSPENSION 6......................................................................................................
ROAD SPRING DATA 6..........................................................................................
SHOCK ABSORBERS 7.........................................................................................
BRAKES 7...............................................................................................................
AIR CONDITIONING 8............................................................................................
WIPER MOTORS 8.................................................................................................
ELECTRICAL 8.......................................................................................................
BULBS9 .................................................................................................................
VEHICLE WEIGHTS AND PAYLOAD 10................................................................
TOWING WEIGHTS 11...........................................................................................
OFF-ROAD PERFORMANCE 11............................................................................
TYRE SIZE AND PRESSURES 12.........................................................................
WHEELS 12............................................................................................................
VEHICLE DIMENSIONS 13....................................................................................
ProCarManuals.com
Page 23 of 667
ProCarManuals.com
Page 24 of 667
GENERAL SPECIFICATION DATA
1
INFORMATION ENGINE - Td5
Type 2.5 litre in-line direct injection Diesel, turbocharged.................................................................................
and intercooled
Number of cylinders 5 in-line, No. 1 cylinder at front of engine.........................................................
Bore 84.450 mm (3.3248 in).................................................................................
Stroke 88.950 mm (3.5020 in)...............................................................................
Capacity 2498 cm
3(152.5 in3) ...........................................................................
Firing order 1 - 2 - 4 - 5 - 3.......................................................................
Compression ratio 19.5:1............................................................
Direction of rotation Clockwise viewed from the front of the engine...........................................................
Dimensions
Length 766 mm (30.1 in).....................................................................
Width 708 mm (27.8 in).......................................................................
Height 788 mm (31.0 in)......................................................................
Emissions standard :-
Engine Serial No. Prefixes 10P to 14P - EU2 Model ECD 2........
Engine Serial No. Prefixes 15P to 19P - EU3 Model ECD 3........
Lubrication
Type Wet sump, pressure fed.................................................................................
Pump type Eccentric rotor, crankshaft driven integral with stiffener........................................................................
plate.
Filter type:
Primary Centrifuge filter....................................................................
Secondary Disposable canister with full flow by-pass...............................................................
Pressure at idle (cold) 3.0 bar (43.5 lbf.in
2) ......................................................
Pressure at 3500 rev/min (hot) 1.5 - 3.0 bar (21.75 - 43.5 lbf.in2) .........................................
Relief valve opening pressure 4.0 bar (58 lbf.in2) ..........................................
Low oil pressure switch opening pressure 0.2 - 0.6 bar (3.0 - 8.8 lbf.in2) .......................
Crankshaft
Main bearing journal diameter 61.9875 - 62.0125 mm..........................................
Crankpin journal diameter 53.99 - 54.01 mm................................................
Crankshaft end float 0.020 - 0.250 mm.........................................................
Main bearings
Number and type 6 half shells (5 main, 1 thrust)..............................................................
Pistons
Type Graphite compound skirt with combustion chamber in.................................................................................
crown.
Clearance in cylinder bore 0.172 - 0.206 mm (measured at bottom of skirt, 90°to ...............................................
gudgeon pin)
Diameter 84.270 - 85.254 mm (measured 90°to gudgeon pin, ..........................................................................
and 40.00 mm from bottom of skirt.)
ProCarManuals.com
Page 25 of 667
04GENERAL SPECIFICATION DATA
2
INFORMATION Gudgeon pins
Type Fully floating, offset towards piston thrust side..................................................................................
Piston rings
Type
Upper compression Barrel edge, chrome plated.................................................
Lower compression Taper faced.................................................
Oil control Bevelled ring with spring................................................................
New ring to groove clearance
Upper compression Not measured.................................................
Lower compression 0.050 - 0.082 mm (0.002 - 0.003 in).................................................
Oil control 0.050 - 0.082 mm (0.002 - 0.003 in)................................................................
Piston ring fitted gap in cylinder bore
Upper compression 0.30 - 0.45 mm (0.0118 - 0.0177 in).................................................
Lower compression 0.40 - 0.60 mm (0.0157 - 0.0236 in).................................................
Oil control 0.25 - 0.40 mm (0.0098 - 0.0157 in)................................................................
Camshaft
Drive Duplex chain.................................................................................
End float 0.6 - 0.16 mm...........................................................................
Number of bearings 6..........................................................
Tappets
Type Hydraulic lash adjusters with followers.................................................................................
Valves
Stem diameter
Exhaust 6.905±0.008 mm (0.271±0.0003 in) ...................................................................
Inlet 6.915±0.008 mm (0.272±0.0003 in) .........................................................................
Head diameter
Exhaust 31.7 mm (1.25 in)...................................................................
Inlet 34.7 mm (1.37 in).........................................................................
Seat face angle
Exhaust 45° ...................................................................
Inlet 30° .........................................................................
Valve face angle
Exhaust 44°48’±12’ ...................................................................
Inlet 29°48’±12’ .........................................................................
Valve springs
Type Parallel, single coil.................................................................................
ProCarManuals.com
Page 26 of 667
GENERAL SPECIFICATION DATA
3
INFORMATION FUEL SYSTEM - Td5
Type Direct injection from pressure regulated supply with.................................................................................
cooled return flow
Pressure regulator setting 4 bar (58 lbf.in
2) ................................................
Pump Electric two stage submersible................................................................................
Pump output
Low pressure 30 l/h (6.6 gal/h) at 0.5 bar (7.25 lbf.in
2) ..........................................................
High pressure 180 l/h (39.6 gal/h) at 4 bar (58 lbf.in2) ..........................................................
Max consumption 30 l/h (6.6 gal/h).............................................................
Injectors Electronic unit injectors...........................................................................
Injector normal operating pressure 1500 bar (21750 lbf.in
2) ..................................
Filter In-line canister filter/water separator with water.................................................................................
detection
COOLING SYSTEM - Td5
Type Pressurised spill return partial flow, thermostatically.................................................................................
controlled
Cooling fans 11 blade axial flow on viscous coupling and 11 blade.....................................................................
axial flow electric
Electric cooling fan switching points
On Vehicle speeds of 50 mph (80 km/h) and below while...........................................................................
ambient temperature is 28°C (82°F) or above
Off Vehicle speeds of 62.5 mph (100 km/h) and above or...........................................................................
ambient temperatures of 25°C (77°F) and below
Coolant pump Centrifugal impeller, belt driven from crankshaft...................................................................
Thermostat Waxstat with pressure relief valve.......................................................................
Thermostat opening temperature
Initial opening 82°C (179°F) ..........................................................
Fully open 96°C (204°F) ...............................................................
Expansion tank cap relief valve operating pressure 1.4 bar (20.3 lbf.in
2) .........
CLUTCH - Td5
Type Diaphragm spring, hydraulically operated with.................................................................................
self-centering pre-loaded release bearing
Drive plate diameter 267 mm.........................................................
Pressure plate diameter 270 mm...................................................
ProCarManuals.com
Page 27 of 667
04GENERAL SPECIFICATION DATA
4
INFORMATION TRANSMISSION - Td5
Main gearbox
Type R380 Single helical constant mesh.......................................................................
Speeds 5 forward, 1 reverse, all synchromesh.............................................................................
Transfer box
Type LT230TE Two speed reduction on main gearbox output. Front.................................................................
and rear drive permanently engaged via a lockable
differential
Rear axle
Type Spiral bevel, fully floating shafts.................................................................................
Ratio 3.54:1.................................................................................
Front axle
Type Spiral bevel, enclosed constant velocity joints, fully.................................................................................
floating shafts, 32°angularity of universal joint on full
lock
Ratio 3.54:1.................................................................................
Propeller shafts
Type, front and rear Tubular 51 mm dia...........................................................
Universal joints Open type Hookes O3EHD.................................................................
ProCarManuals.com
Page 28 of 667
GENERAL SPECIFICATION DATA
5
INFORMATION STEERING
Power steering box
Make/type Adwest Varamatic - worm and roller box........................................................................
Ratio Variable: straight ahead 19.3:1 on lock 14.3:1.................................................................................
Steering wheel turns, lock-to-lock 3.375....................................
Steering pump
Make/type Hobourn-Eaton series 500........................................................................
Steering geometry
Steering wheel diameter 412 mm (16.22 in)..................................................
Toe-out measurement 0 to 2 mm toe out......................................................
Toe-out included angle 0°to 0°20’ .....................................................
Camber angle 0°* ..................................................................
Castor angle 3°* .....................................................................
Swivel pin inclination static 7°* ...............................................
* Check with vehicle on level ground, in unladen
condition and five gallons of fuel. Rock the front of the
vehicle up and down to allow it to take up a normal
static position.
Turning circle between kerbs
90 models:
265/75 x 16 tyres 12,65 m (41.5 ft)..............................................................
All other tyres 11,70 m (38.4 ft)...................................................................
110 models:
750 x 16 tyres 13,41 m (44 ft)..................................................................
130 models:
750 x 16 tyres 15,24 m (50 ft)..................................................................
ProCarManuals.com
Page 29 of 667
04GENERAL SPECIFICATION DATA
6
INFORMATION SUSPENSION
Type Coil springs controlled by telescopic dampers front.................................................................................
and rear.
Front Transverse location of axle by Panhard rod, and fore.................................................................................
and aft location by two radius arms. Anti-roll bar fitted
as standard on 90 models with 265/75 tyres and 130
models.
Rear Fore and aft movement inhibited by two tubular trailing.................................................................................
links. Lateral location of axle by a centrally positioned
’A’frame, upperlink assembly, bolted at the apex to a
ball joint mounting. Anti-roll bar fitted as standard on
90 models with 265/75 tyres, 110 models with self
levelling unit, and 130 models.
ROAD SPRING DATA
90 (2400 Kg) Part No. Colour Code
Front - Driver’s side NRC 9446 Blue/green
Front - Passenger side NRC 9447 Blue/yellow
Rear - Driver’s side NRC 9448 Blue/red
Rear - Passenger side NRC 9449 Yellow/white
90 (2550 Kg)
Front - Driver’s side NRC 9446 Blue/green
Front - passenger side NRC 9447 Blue/yellow
Rear - Driver’s side NRC 9462 Green/yellow/red
Rear - Passenger side NRC 9463 Green/yellow/white
110 (3050 Kg)
Front - both sides NRC 8045 Yellow/yellow
Rear - both sides NRC 6904 Red/green
110 Levelled (2950 Kg)
Front - both sides NRC 8045 Yellow/yellow
Rear - both sides NRC 7000 Green/white
110 (3400 Kg)
Front - both sides NRC 8045 Yellow/yellow
Rear - both sides NRC 6904 Red/green
Rear helper springs - both sides RRC 3266 No colour code
110 (3600 Kg)
Front - Driver’s side NRC 9448 Blue/red
Front - passenger side NRC 9449 Yellow/white
Rear - both sides NRC 6904 Red/green
Rear helper springs - both sides RRC 3226 No colour code
130 (3500 Kg)
Front - driver’s side NRC 9448 Blue/red
Front - passenger side NRC 9449 Yellow/white
Rear - driver’s side NRC 6389 Red/red
Rear - passenger side NRC 6904 Red/green
Front/rear helper springs - both sides RRC 3266 No colour code
ProCarManuals.com
Page 30 of 667
GENERAL SPECIFICATION DATA
7
INFORMATION SHOCK ABSORBERS
Type Telescopic, double-acting non-adjustable.................................................................................
Bore diameter 35.47mm...................................................................
BRAKES
Front brake
Caliper AP Lockheed, four opposed pistons..............................................................................
Operation Hydraulic, self adjusting.........................................................................
Disc 90 - Solid, outboard, 110/130 - Ventilated, outboard..................................................................................
Disc diameter 298 mm (11.73 in)...................................................................
Disc thickness 90 - 14,1 mm (0.56in), 110/130 - 24mm (0.95 in)..................................................................
Wear limit 1 mm (0.04in) per side of disc.........................................................................
Disc run-out maximum 0,15mm (0.006 in).....................................................
Pad area 58 cm
2(9.0 in2) ..........................................................................
Total swept area 801,3 cm2(124.2 in2) ...............................................................
Pad material Ferodo 3440 non asbestos.....................................................................
Pad minimum thickness 3 mm (0.12in)...................................................
Rear brake
Caliper AP Lockheed opposed piston..............................................................................
Operation Hydraulic, self adjusting.........................................................................
Disc Solid, outboard..................................................................................
Disc diameter 90 - 290 mm (11.42 in), 110/130 - 298 mm (11.73)...................................................................
Disc thickness 90 - 12,5 mm (0.49 in), 110/130 - 14,1 mm (0.56 in)..................................................................
Wear limit 90 - 0,38 mm (0.015 in), 110/130 - 1,0 mm (0.04 in).........................................................................
per side of disc
Disc run-out maximum 0,15 mm (0.006 in).....................................................
Pad area 90 - 30,5 cm
2(4.37 in2), 110/130 - 36,2 cm2(5.61 in2) ..........................................................................
Total swept area 90 - 694 cm2(106.98 in2) ...............................................................
Pad material Ferodo 3440 non asbestos.....................................................................
Pad minimum thickness UP TO 02MY - 3 mm (0.12 in)...................................................
Pad minimum thickness From 02MY - 2 mm (0.08 in)...................................................
Parking brake
Type Mechanical, cable operated drum brake on the rear of.................................................................................
the transfer gearbox output shaft
Drum internal diameter 254 mm (10.0 in).....................................................
Width 70 mm (2.75 in)................................................................................
Pad material Ferodo 3611 non asbestos.....................................................................
Servo/master cylinder
Manufacturer Lucas....................................................................
Servo type LSC 80........................................................................
Master cylinder type 25,4 mm (1.0 in) diameter, tandem.........................................................
Pressure reducing valve, failure conscious Cut-in pressure, 90 - 24 bar (360 Ibf/in
2) ratio 4.0:1, ......................
110 - 43 bar (645 Ibf/in2) ratio 2.9:1*
NOTE: * Pressure reducing valves are not fitted to all 110 specifications.
ProCarManuals.com