sensor LAND ROVER DISCOVERY 1995 User Guide

MAINTENANCE
19
MAINTENANCE
RESET EMISSION MAINTENANCE REMINDER -
USA
The emission maintenance reminder is designed to
activate at 52,500 and 105,000 miles respectively and
will illuminate a 'Service Engine' red warning light in
instrument binnacle.
The emission maintenance reminder must be reset
after required maintenance has been carried out and
a new tamperproof label fitted by a Land Rover of
North America dealer. This emission maintenance
reminder is part of the Emission Control System
Reset
1.The control unit is located in the passenger
footwell.
2.Identify control unit and remove from plug.
3.Remove tamperproof label to reveal access hole
for resetting.
4.Place a thin metallic probe into access hole and
momentarily electrically short between reset pins
inside unit.RECOMMENDED SERVICE ITEMS
Refer Service Schedule sheets for intervals.
Clean sunroof drain tubes, clean and lubricate guide
rails and slides.
Renew the hydraulic brake fluid.
See BRAKES,
Repair, Brake System Bleed
Renew all hydraulic brake fluid, seals, brake servo
filter and flexible hoses.
All working surfaces of the master cylinder and caliper
cylinders should be examined and renewed where
necessary.
ABS vehicles only - renew hydraulic brake fluid and
flexible hoses examine the working surfaces of the
caliper cylinders and renew the seals or cylinders
where necessary.
Air cleaner - When the vehicle is used in dusty or field
conditions or deep wading, frequent attention to the
air cleaner may be required.
ABS vehicles used extensively in arduous off-road
conditions - check the rear wheel road speed sensor
for abrasive wear.

12ENGINE
20
REPAIR CYLINDER HEAD GASKET
Service repair no - 12.29.02
Remove
1.Disconnect battery negative lead.
2.Remove bonnet [Hood].
See CHASSIS AND
BODY, Repair, Bonnet [Hood]
3.Drain coolant.
4.Remove air cleaner assembly.
See FUEL
SYSTEM, Repair, Air Cleaner
5.Detach crankcase ventilation valve and side
breather hose from rocker cover and move to
one side.
6.Remove injection pipes.
7.Disconnect spill rail from fuel injectors.
8.Remove fuel injectors and sealing washers.
Identify each injector to the location from which it
is removed.
See FUEL SYSTEM, Repair,
Injectors
9.Remove inter-connecting harness from glow
plugs.
10.Remove glow plugs.
See FUEL SYSTEM,
Repair, Glow Plugs
11.Remove top hose, radiator to thermostat.
12.Disconnect by-pass hose from thermostat.
13.Disconnect hose, thermostat to water pump.
14.Disconnect water temperature sensor lead.
15.Remove hose inter-cooler to induction manifold.
16.Remove induction manifold.
See MANIFOLD
AND EXHAUST SYSTEM, Repair, Exhaust
Manifold - Tdi
17.Remove exhaust manifold and turbocharger
assembly.
See MANIFOLD AND EXHAUST
SYSTEM, Repair, Exhaust Manifold - Tdi
18.Disconnect heater hose from water pump and
move heater rail aside.
19.Disconnect heater hose from rear of cylinder
head.
20.Remove bolt securing air cleaner mounting
bracket to support strut.
21.Remove bolt securing harness bracket to
cylinder head.
22.Remove rear lifting bracket, this will also release
clips securing transmission and engine breather
pipes and multiplug. Note loose spacer under
clip securing engine breather pipe and multiplug.

12ENGINE
2
SPECIFICATIONS, TORQUECylinder head
Cylinder head to cylinder block See repair section......................................................
Stub pipe heater feed 22.................................................................................
Water temperature sensor 14.........................................................................
Blanking plug cylinder head 14.......................................................................
Engine lifting brackets 25................................................................................
Electrical harness clip bracket 25...................................................................
Exhaust manifold stud 10................................................................................
Exhaust manifold nut 45.................................................................................
Inlet manifold stud 8.......................................................................................
Inlet manifold nut and bolt 25..........................................................................
Air temperature sensor, inlet manifold 14.......................................................
Blanking plug, inlet manifold 14......................................................................
Heatshield to inlet manifold 6.........................................................................
Glow plug 20...................................................................................................
Glow plug terminal nut 2................................................................................
Injector clamp (stud) 8...................................................................................
Injector clamp (nut) 25....................................................................................
Thermostat housing 25...................................................................................
Water outlet elbow to thermostat housing 25..................................................
Water temperature switch, thermostat housing 11..........................................
Plug thermostat housing 6.............................................................................
Rocker shaft pedestal bolt 5 + 50° .....................................................................
Rocker cover (stud) 8.....................................................................................
Rocker cover (fixing nut) 10............................................................................
Breather cyclone to rocker cover 9................................................................
Tappet adjusting nut 16..................................................................................
Front cover to cylinder block 25......................................................................
Front cover plate to front cover 25..................................................................
Static idler - timing belt (stud) 10.....................................................................
Static idler - timing belt (nut) 45......................................................................
Tensioner (timing belt) 45...............................................................................
Camshaft hub bolt 80......................................................................................
Timing pulley to camshaft hub 25...................................................................
Fuel injection pump (stud) 8...........................................................................
Fuel injection pump (nut) 25...........................................................................
Abutment bracket to injection pump 25...........................................................
Support bracket injection pump to cylinder block 25.......................................
Fuel injection pump access plte to front cover plate 25..................................
Timing pulley to injection pump hub 25...........................................................
TV Damper pulley bolt to crankshaft 80 + 90° .....................................................
Fan pulley to hub 25.......................................................................................
Fan and viscous coupling to hub 45...............................................................
Auto tensioner, auxiliary drive (stud) 14..........................................................
Auto tensioner, auxiliary drive (nut) 45...........................................................
Auxiliary mounting bracket to cylinder block (stud) 8.....................................
Auxiliary mounting bracket to cylinder block (bolt and nut) 25........................
Water pump to block and mounting plate 25..................................................
Water pump pulley to hub 25..........................................................................

Tdi
3
SPECIFICATIONS, TORQUE Turbo charger oil drain adaptor to block 42....................................................
Oil drain pipe to turbocharger 25....................................................................
Turbocharger oil drain pipe to adaptor 38.......................................................
Turbocharger oil feed pipe adaptor to block 25...............................................
Turbocharger oil feed pipe to adaptor 25........................................................
Oil feed pipe to turbocharger 19.....................................................................
Turbocharger to cylinder head (stud) 10.........................................................
Turbocharger to cylinder head (nut) 45...........................................................
Turbocharger to blanking plate 25..................................................................
Turbocharger to EGR valve 25.......................................................................
EGR delivery tube to valve 25........................................................................
EGR delivery tube to mixing tube 25..............................................................
Fuel lift pump to filter (union) 15.....................................................................
Fuel filter from lift pump (banjo bolt) 33...........................................................
Fuel filter to fuel injection pump (banjo bolt) 33..............................................
Fuel injection pump from fuel filter (banjo bolt) 25..........................................
Injector pipes to injectors and fuel injection pump 29.....................................
Spill rail to injectors (banjo bolt) 10.................................................................
Spill rail to injection pump (banjo bolt) 25.......................................................
Boost pipe injection pump (banjo bolt) 10.......................................................
Plug, rear of injection pump 29.......................................................................
PAS pump to mounting plate 25.....................................................................
PAS pump mounting plate to auxiliaries mounting bracket 25........................
PAS pump pulley to hub 25............................................................................
Generator to auxiliaries mounting bracket 25.................................................
Starter motor (bolt and nut) 45........................................................................
Tachometer electrical connection 4...............................................................
Air conditioning compressor
Compressor mounting bracket to front cover 45.............................................
Compressor to mounting bracket (stud) 8......................................................
Compressor to mounting bracket (nut) 25......................................................
Belt tensioner pulley to tensioner arm 45........................................................
Belt tensioner assembly to front cover plate 25..............................................
Idler pulley to front cover plate 45...................................................................
Compressor belt guard (nut) 25......................................................................
Sensors to water outlet elbow (air/con) 25......................................................
Blanking plug, water outlet elbow (air/con) 25................................................
Generator mounting bracket to front cover 45................................................
Generator to mounting bracket 85..................................................................
Generator pulley to hub 95.............................................................................
Generator belt guard 25..................................................................................

12ENGINE
4
REPAIR CYLINDER HEAD GASKETS - RENEW
Service repair no - 12.29.01
1.Drain cooling system.
See COOLING SYSTEM,
Adjustment, Coolant
2.Remove inlet manifold.See FUEL SYSTEM,
Repair, Intake Manifold
3.Remove generator.
4.If fitted, remove compressor.
See AIR
CONDITIONING, Repair, Compressor
5.Remove rocker shafts.See Rocker Shaft
Renew
6.Remove push rods.
7.Remove both exhaust manifolds.
See
MANIFOLD AND EXHAUST SYSTEM, Repair,
Exhaust Manifold - V8i
8.Remove air cleaner assembly.See FUEL
SYSTEM, Repair, Air Cleaner Assembly
9.Remove air flow sensor.See FUEL SYSTEM,
Repair, Air Flow Sensor
10.Remove ground leads from rear of left hand
cylinder head
11.Right hand cylinder head - remove breather pipe
from lifting bracket.
12.Loosen cylinder head bolts, reversing tightening
sequence.
13.Remove cylinder heads.
14.Remove cylinder head gaskets.
15.Clean exhaust mating faces.
16.Clean head and block faces.
17.Fit new cylinder head gaskets, word TOP
uppermost. DO NOT use sealant.
18.Oil cylinder bores.
19.Clean threads of head bolts and lightly oil.
20.Locate cylinder heads on block.
21.Locate cylinder head bolts in position illustrated.
96 mm long bolts - 2, 4, 6, 7, 8, 9, 10
66 mm long bolts - 1, 3, 5
NOTE: There are no bolts fitted in the four
lower holes in each cylinder head.
NOTE: Left hand cylinder head illustrated,
arrow points to front of vehicle.
22.Tighten bolts progressively in sequence, shown
to
20 Nmthen a further 180°±5°
23.Reverse removal procedure. 1 to 11.

12ENGINE
6
REPAIR 11.Place one end of gasket into cover recess with
edge firmly against recess wall, holding
remainder of gasket clear. Work around cover,
pressing gasket into place ensuring edge firmly
contacts recess wall.
12.Allow cover to stand for thirty minutes before
fitting.
13.Fit rocker cover to cylinder head with four
screws, short screws inboard, tighten to
9 Nm.
14.Position fuel pipes.
15.Fit breather pipe to rocker cover, tighten clip.
16.Fit coolant pipes to inlet manifold, tighten bolts.
17.Fit spark plug leads to plugs and retaining clips.
18.Connect purge pipe from charcoal canister at
plenum, tighten clip.
ROCKER COVER - LEFT HAND - RENEW
Service repair no - 12.29.40
1.Remove air flow sensor.
See FUEL SYSTEM,
Repair, Air Flow Sensor
2.Remove plenum chamber.See FUEL SYSTEM,
Repair, Plenum Chamber
3.Remove dipstick.
4.Remove spark plug leads from plugs and
retaining clips.
5.Disconnect HT lead from coil.
6.Remove generator heat shield securing nut from
rocker cover.
7.Remove air flow meter harness clip.
8.Remove bolt securing dipstick tube clip.
9.Remove four rocker cover bolts, remove rocker
cover.
10.Discard gasket
11.Remove plug lead retaining clips from rocker
cover, fit to new rocker cover.
12.Clean and dry rocker cover and cylinder head
mating faces, using Bostik cleaner 6001.
NOTE: Gasket fits one way round only. It
must be fitted accurately, first time.
Subsequent movement will destroy
bonding.
13.Apply Bostik 1775 impact adhesive to rocker
cover seal face and gasket, using a brush to
ensure an even film. Allow adhesive to become
touch dry, approximately fifteen minutes.
14.Place one end of gasket into cover recess with
edge firmly against recess wall, holding
remainder of gasket clear. Work around cover,
pressing gasket into place ensuring edge firmly
contacts recess wall.
15.Allow cover to stand for thirty minutes before
fitting.
16.Fit rocker cover to cylinder head with four
screws, short screws inboard. Tighten to
9 Nm.
17.Position dipstick tube clip. Fit and tighten bolts.
18.Fit and tighten air flow meter harness clip.
19.Fit generator heat shield to rocker cover.
20.Connect HT lead to coil.
21.Connect spark plug leads to plugs and retaining
clips.
22.Fit dipstick.
23.Fit plenum chamber.
24.Fit air flow meter.

12ENGINE
12
REPAIR
12.Ensure service tools LRT-12-010 and
LRT-12-091 are scrupulously clean. Coat seal
guide and oil seal journal with clean engine oil.
CAUTION: Do not handle oilseal lip, check
it is not damaged. Ensure outside diameter
remains clean and dry.
13.Position oil seal guide LRT-12-010 on crankshaft
flange.
NOTE: Lubricant coating must cover seal
guide outer surface completely to ensure
that oil seal lip is not turned back during
assembly. Position oil seal, lipped side towards
engine, on seal guide. Seal outside diameter
MUST be clean and dry.
14.Fit oil seal using tool LRT-12-091. Remove seal
guide.
15.Tighten rear main bearing cap to
90 Nm.
16.Fit sump.
17.Fit flywheel or flexible drive plate and ring gear.ENGINE
Service repair no - 12.41.01
Remove
1.Park vehicle on level ground and apply park
brake.
2.De-pressurise fuel system.
See FUEL
SYSTEM, Repair, Depressurising Fuel
System
3.Remove bonnet [hood].See CHASSIS AND
BODY, Repair, Bonnet [Hood]
4.Remove battery.See ELECTRICAL, Repair,
Battery
5.Remove radiator/oil coolers.See COOLING
SYSTEM, Repair, Radiator/Oil Coolers
6.Place an absorbent cloth around fuel feed hose
at fuel rail and release compression nut.
Remove feed hose from rail, seal end of pipes
with masking tape to prevent ingress of dirt.
7.Release fuel return hose clamp and remove
hose from pressure regulator, seal both
openings with masking tape to prevent ingress of
dirt.
8.Remove vacuum hose from rear of regulator.
9.Manual vehicles: Disconnect throttle cable from
bracket. Automatic vehicles: Detach throttle
bracket from plenum chamber and lay assembly
to one side.
See FUEL SYSTEM, Repair,
Plenum Chamber DO NOT DISTURB KICK
DOWN CABLE SETTING.
10.Remove ram housing.See FUEL SYSTEM,
Repair, Ram Housing
11.Remove air flow sensor.See FUEL SYSTEM,
Repair, Air Flow Sensor
12.Remove air cleaner assembly.See FUEL
SYSTEM, Repair, Air Cleaner Assembly
13.Remove Generator.See ELECTRICAL,
Description and operation, Generator
14.Release air conditioning compressor from its
mounting and lay to one side. DO NOT
discharge air conditioning system.
See AIR
CONDITIONING, Repair, Compressor

V8i
13
REPAIR
NOTE: Release bolts securing compressor
mounting bracket to engine and remove
bracket to enable temporary lifting eye
ETC 5964 to be fitted. Secure lifting eye to
mounting bracket fixing points with suitable bolts
of equivalent size, pitch and thread. Leave lifting
eye attached until engine is reinstalled in vehicle.
15.Place drain tray underneath vehicle.
16.Disconnect hose from reservoir to power
steering pump. Secure hose end above level of
fluid reservoir to avoid unnecessary loss of fluid.
17.Disconnect power steering pump to power
steering box hose. Seal hose and pump
openings with masking tape to prevent ingress of
dirt. Wipe away any fluid spillage from chassis or
steering box.
18.Disconnect fuel temperature and coolant
temperature sensor multi-plugs.
19.Disconnect leads from coil.
20.Identify each injector multi-plug for re-assembly
and disconnect plugs from injectors.
21.Manoeuvre harness from behind fuel rails and
place to one side clear of engine assembly.
22.Remove two clamps securing gearbox oil cooler
pipes to engine block.
23.Remove engine mounting fixings on both sides
of cylinder block.
24.Fit lifting chains to engine lifting eyes as shown
in illustration RR1780E.
1. L/H Front chain 356mm total overall length.
2. R/H Front chain 330mm total overall length.
3. R/H Rear chain 457mm total overall length.
NOTE: All chain dimensions are measured
from end of lifting hook to end of last link
in chain.
25.Fit chain lifting eye to a suitable engine hoist.
Raise hoist high enough to enable engine
mountings to be removed, and withdraw rubber
mountings.
26.Lower hoist until engine rests securely on engine
mounting brackets. Remove lifting chains and
hoist.
27.Disconnect two heater hoses located on top of
right hand rocker cover.
28.Remove ground strap from rear of left hand
cylinder head. DO NOT remove from retaining
clip.
29.Remove all electrical harnesses from retaining
clips at rear of engine.
30.Remove transmission breather pipes from
retaining clip on rear lifting eye.
31.Remove top two bolts securing bell housing to
cylinder block.
32.Raise front of vehicle, lower vehicle on to axle
stands.
33.Remove bell housing bottom cover. Remove
gasket from bell housing face.
34.Remove nuts securing exhaust downpipes to
manifolds, remove heat shield from right hand
side downpipe.
35.Remove electrical leads from starter motor
solenoid. Disconnect multi-plug from oil level
sensor on side of sump, if fitted.
NOTE: Instructions 37, 38 and 39 refer to
automatic vehicles only.
36.With assistance rotate engine at crankshaft
pulley until two access holes in drive plate/ring
gear assembly are visible.
37.Remove two bolts visible through access holes.
Mark one access hole and one bolt hole to
ensure unit is reassembled in its original position
38.Rotate crankshaft 180Ê until two remaining
access holes are visible, remove two bolts.

V8i
15
REPAIR OIL SUMP
Service repair no - 12.60.44
Remove
1.Drain engine oil
See SECTION 10,
Maintenance, Under Vehicle Maintenance
2.Fit drain plug. Tighten to40 Nm.
3.If fitted, disconnect low oil level sensor multiplug.
4.Remove bolt securing dipstick tube to rocker
cover.
5.Working form the centre outwards, progressively
loosen and remove 17 bolts securing sump.
Remove sump.
6.Remove all traces of sealant from mating
surfaces of sump, cylinder block and front cover,
using a suitable solvent or plastic scraper.
7.Degrease mating surfaces of sump, cylinder
block and front cover.Refit
8.Apply RTV Hylosil White sealant to mating
surface of sump.
9.Position sump, tighten bolts finger tight.
10.Tighten bolts progressively in sequence shown.
Tighten to
18 Nm.
11.Fit bolt securing dipstick tube to rocker cover.
12.If fitted, connect low oil level sensor multiplug.

4.0 V8
3
REPAIR ENGINE ASSEMBLY
Service repair no - 12.41.01/99
Remove
1.Position vehicle on ramp.
2.Remove bonnet.
See CHASSIS AND BODY,Repair, Bonnet [Hood]
3.Remove radiator.See COOLING SYSTEM,
Repair, Radiator
4.Remove plenum chamber.See FUEL SYSTEM
SFI, Repair, Plenum Chamber
5.Remove mass air flow sensor.See FUEL
SYSTEM SFI, Repair, Mass Air Flow Sensor
(MAF Sensor)
6.Slacken hose clip securing bottom hose to
expansion tank.
7.Disconnect hose.
8.Remove 2 nuts securing expansion tank.
9.Remove nut and bolt securing expansion tank.
10.Remove expansion tank.
11.Disconnect servo vacuum hose from ram
housing.
12.Disconnect battery sensing lead Lucar from
generator.
13.Remove generator terminal cover.
14.Remove 2 terminal nuts and release leads from
terminals.
15.Release purge hose from ram pipe housing.
16.Position cloth to absorb fuel spillage.
17.Slacken clip securing fuel return hose to fuel rail.
18.Disconnect hose.
19.Plug connections.
20.Disconnect fuel feed hose union.
21.Plug connections. Position hoses aside.
22.Slacken clip securing heater return hose to pipe.
23.Disconnect hose.24.Slacken clip securing heater feed adaptor hose
to inlet manifold.
25.Remove bolt securing pipe bracket.
26.Disconnect feed hose from inlet manifold.
27.Disconnect hose/pipe assembly.
28.Disconnect leads from spark plugs and remove
ignition coils.
See FUEL SYSTEM SFI, Repair,
Ignition Coils
29.Disconnect fuel temperature sensor multiplug.
30.Disconnect coolant sensor multiplug.
31.Disconnect temperature gauge sensor lead.
32.Release camshaft sensor multiplug from bracket
and disconnect multiplug.
33.Disconnect oil pressure switch Lucar.
34.Disconnect air intake temperature sensor
multiplug.
35.Disconnect 8 injector multiplugs.
36.Remove 4 nuts securing harness brackets to
inlet manifold.
37.Release harness brackets.
38.Remove bolts securing gearbox breather pipes
to engine lifting bracket.