oil LAND ROVER DISCOVERY 1995 Owner's Manual

GENERAL FITTING REMINDERS
7
INFORMATION COTTER PINS
1.Fit new cotter pins throughout when replacing
any unit.
2.Always fit cotter pins where cotter pins were
originally used. Do not substitute spring
washers: there is always a good reason for the
use of a cotter pin.
3.All cotter pins should be fitted as shown unless
otherwise stated.
NUTS
1.When tightening a slotted or castellated nut
never loosen it back to insert cotter pin or locking
wire except in those recommended cases where
this forms part of an adjustment. If difficulty is
experienced, alternative washers or nuts should
be selected, or washer thickness reduced.
2.Where self-locking nuts have been removed it is
advisable to replace them with new ones of the
same type.
NOTE: Where bearing pre-load is involved
nuts should be tightened in accordance
with special instructions.
LOCKING WIRE
1.Fit new locking wire of the correct type for all
assemblies incorporating it.
2.Arrange wire so that its tension tends to tighten
the bolt heads, or nuts, to which it is fitted.SCREW THREADS
1.Both UNF and Metric threads to ISO standards
are used. See below for thread identification.
2.Damaged threads must always be discarded.
Cleaning up threads with a die or tap impairs the
strength and closeness of fit of the threads and
is not recommended.
3.Always ensure that replacement bolts are at
least equal in strength to those replaced.
4.Do not allow oil, grease or jointing compound to
enter blind threaded holes. The hydraulic action
on screwing in the bolt or stud could split the
housing.
5.Always tighten a nut or bolt to the recommended
torque value. Damaged or corroded threads can
affect the torque reading.
6.To check or re-tighten a bolt or screw to a
specified torque value first loosen a quarter of a
turn, then re-tighten to the correct value.
7.Oil thread lightly before tightening to ensure a
free running thread, except in the case of
threads treated with sealant/lubricant, and
self-locking nuts.
UNIFIED THREAD IDENTIFICATION
1. Bolts
A circular recess is stamped in the upper surface
of the bolt head.
2. Nuts
A continuous line of circles is indented on one of
the flats of the hexagon, parallel to the axis of
the nut.
3. Studs, Brake Rods, etc.
The component is reduced to the core diameter
for a short length at its extremity.

LUBRICANTS, FLUIDS AND CAPACITIES
1
INFORMATION RECOMMENDED LUBRICANTS AND FLUIDS -
USA VEHICLES
AMBIENT TEMPERATURE°C
COMPONENT SPECIFICATION VISCOSITY -30 -20 -10 0 10 20 30 40 50
Engine Use oils to API 5W/20 )
service level
SGSH 5W/30 )
or 5W/40 )
RES.22.OL.G4
or
CCMC G4 10W/30
10W/40 )
10W/50 )
15W/40 )
15W/50 )
20W/40 )
20W/50 )
Automatic gearbox ATF Dexron IID
Final drive units API or GL5 90 EP
Swivel pin housings MIL - L - 2105 or
MIL - L - 2105B, C
or D 80W EP
Power steering ATF Dexron IID
LT 230T API GL4 or GL5
transfer gearbox MIL - L - 2105 or
MIL - L - 2105B
Brake reservoir Brake fluid must have a minimum
boiling point of 260°C (500ÊF) and
comply with FMVSS/116/DOT 4
Lubrication nipples
(hubs, ball joints,
etc.)NLGI-2 multipurpose lithium based
grease
See table on page 3 for remaining vehicle components

09LUBRICANTS, FLUIDS AND CAPACITIES
2
INFORMATION RECOMMENDED LUBRICANTS AND FLUIDS
All climates and conditions
AMBIENT TEMPERATURE°C
COMPONENT SPECIFICATION VISCOSITY -30 -20 -10 0 10 20 30 40 50
Petrol modelsOils must meet: 5W/30
Engine sump
RES.22.OL.G-4 5W/40
or 5W/50
CCMC G-4 or 10W/30
API SG or SH 10W/40
10W/50
15W/40
15W/50
20W/40
20W/50
25W/40
25W/50
DieselRES.22.OL.PD-2 15W/40
Engine sump or CCMC PD-2
or API CD
Main Gearbox
AutomaticATF Dexron IID
Main Gearbox
manualATF Dexron IID
Final drive units API or GL5 90 EP
Swivel pin housings MIL - L - 2105 or
MIL - L - 2105B 80 EP
CorD
Power steering ATF Dexron IID
Transfer box API GL4 or GL5 90 EP
LT230T MIL - L - 2105 or
MIL - L - 2105B 80 EP
CorD

LUBRICANTS, FLUIDS AND CAPACITIES
3
INFORMATION Propeller shaft Front
and RearNLGI - 2 Multi-purpose Lithium based GREASE
Lubrication nipples
(hubs, ball joints
etc.)
Seat slides
Door lock striker
Brake and clutch
reservoirsBrake fluids having a minimum boiling point of 260°C (500°F) and complying with
FMVSS 116 DOT4
Engine coolant Use an ethylene glycol based anti-freeze (containing no methanol)
V8i, Tdi, Mpi with non-phosphate corrosion inhibitors suitable for use in aluminium engines to ensure
the protection of the cooling system against frost and corrosion in all seasons. Use one
part anti-freeze to one part water for protection down to -36°C (-33°F).
IMPORTANT: Coolant solution must not fall below proportions one part
anti-freeze to three parts water, i.e. minimum 25% anti-freeze in coolant otherwise
damage to engine is liable to occur. Or a maximum of 60%.
Battery lugs, Petroleum jelly.
Earthing surfacesNOTE: Do not use Silicone Grease
where paint has
been removed
Air Conditioning
System Refrigerant Use only refrigerant R134a
Compressor Oil Nippon Denso ND-oil8 Unipart ND-oil8
ABS Sensor Silicone grease: Staborags NBU - Wabco 830 502,0634
bush-rear Wacker chemie 704 - Wabco 830 502,0164
Kluber GL301
LUBRICATION PRACTICE
Use a high quality oil of the correct viscosity range and service classification in the engine during maintenance and
when topping up. The use of oil not to the correct specification can lead to high oil and fuel consumption and
ultimately to damaged components.
Oil to the correct specification contains additives which disperse the corrosive acids formed by combustion and
prevent the formation of sludge which can block the oilways. Additional oil additives should not be used. Always
adhere to the recommended servicing intervals.
WARNING: Many liquids and other substances used in motor vehicles are poisonous. They must
not be consumed and must be kept away from open wounds. These substances, among others,
include anti-freeze windscreen washer additives, lubricants and various adhesives.

09LUBRICANTS, FLUIDS AND CAPACITIES
4
INFORMATION CAPACITIES
The following capacity figures are approximate and are provided as a guide only.
Capacities (approx.)* Litres Imp.Unit US unit
Engine sump oil
- 300Tdi models 5,8...................................................... 10.20 pt 12.30 pt
- V8i petrol models 3.9 6,1............................................ 10.70 pt 12.90 pt
- Mpi petrol models 4,90.................................................. 8.70 pt 10.40 pt
Extra when refilling after fitting new filter
- 300Tdi models 0,85...................................................... 1.50 pt 1.80 pt
- V8i petrol models 0,56.................................................. 1.00 pt 1.20 pt
- Mpi 0,4........................................................................ 0.70 pt 0.85 pt
Manual gearbox 2,67............................................................... 4.70 pt 5.70 pt
Automatic gearbox 9,1........................................................... 16.00 pt 19.20 pt
Transfer gearbox oil 2,30......................................................... 4.00 pt 4.90 pt
Front differential 1,70............................................................... 3.00 pt 3.60 pt
Rear differential 1,70................................................................ 3.00 pt 3.60 pt
Power steering box and reservoir LHD 2,90............................ 5.00 pt 6.00 pt
Power steering box and reservoir RHD 3,40............................ 6.00 pt 7.20 pt
Swivel pin housing oil (each) 0,35............................................ 0.60 pt 0.75 pt
Fuel tank usable fuel 89,0........................................................ 19.5 gall 23 gall
Cooling system
- 300Tdi models 11,50...................................................... 20.20 pt 24.30 pt
- V8i petrol models 11,30.................................................. 20.00 pt 23.90 pt
- Mpi 10,00........................................................................ 17.60 pt 21.00 pt
Washer bottle 7,0................................................................... 12.30 pt 14.80 pt
NOTE: * All levels must be checked by dipstick or level plugs as applicable. When draining oil
from the ZF automatic gearbox, oil will remain in the torque converter, refill to high level on
dipstick only.

LUBRICANTS, FLUIDS AND CAPACITIES
5
INFORMATION ANTI-FREEZE
ENGINE TYPE MIXTURE STRENGTH PERCENTAGE PROTECTION
CONCENTRATION LOWER
TEMPERATURE
LIMIT
V8i Engine One part anti-freeze
Diesel Engine One part water 50%
Complete protection-33°F
Vehicle may be driven away immediately from cold - 36°C
Safe limit protection-41°C
Coolant in mushy state. Engine may be started and driven away after warm-up
period-42°F
Lower protection-47°C
Prevents frost damage to cylinder head, block and radiator. Thaw out before
starting engine-53°F
CAUTION: Anti-freeze content must never be allowed to fall below 25% otherwise damage to the
engine is liable to occur. Also, anti-freeze content should not exceed 60% as this will greatly
reduce the cooling effect of the coolant.
FUEL REQUIREMENTS
Catalyst vehicles
Vehicles equipped with catalytic converter are designed to use ONLY unleaded fuel. Unleaded fuel must be used
for the emission control system to operate properly. Its use will also reduce spark plug fouling, exhaust system
corrosion and engine oil deterioration.
Using fuel that contains lead will result in damage to the emission control system and could result in loss of
warranty coverage. The effectiveness of the catalysts in the catalytic converters will be seriously impaired if leaded
fuel is used. The vehicle is equipped with an electronic fuel injection system, which includes two oxygen sensors.
Leaded fuel will damage the sensors, and will deteriorate the emission control system.
Regulations require that pumps delivering unleaded fuel be labelledUNLEADED.Only these pumps have nozzles
which fit the filler neck of the vehicle fuel tank.

09LUBRICANTS, FLUIDS AND CAPACITIES
6
INFORMATION RECOMMENDED FUEL
Petrol engines
- with catalytic converter unleaded only, 95 RON (USA 90 CLC or AKI)................................................
- non catalytic, 9.35:1 compression ratio leaded 97 RON/unleaded 95 RON.......................
- non catalytic, 8.13:1 compression ratio leaded 90 RON/unleaded 95 RON.......................
- Australia minimum 91 RON unleaded......................................................................
Diesel engines
300Tdi Diesel fuel oil,distillate,diesel fuel, automotive gas or...........................................................................
Derv to British standard 2869, Class A1 or A2
Using fuel with an octane rating lower than stated above could seriously impair vehicle performance.
CAUTION: Do not use oxygenated fuels such as blends of methanol/ gasoline or ethanol/gasoline
(e.g. 'Gasohol'). Take care not to spill fuel during refuelling.

MAINTENANCE
3
MAINTENANCE VEHICLE EXTERIOR
CHECK/ADJUST HEADLAMP ALIGNMENT
Check/adjust headlamp and auxiliary alignment.
CHECK FRONT WHEEL ALIGNMENT
Use recognised wheel alignment equipment to
perform this check and adjustment.
See STEERING,
Adjustment, Front Wheel Alignment
REMOVE WHEELS, CHECK TYRES
Check tyres (including spare) for compliance with
manufacturers' specification.
Check visually for cuts, lumps, bulges, uneven tread
wear and tread depth. Check road wheels for
damage.
Check/adjust tyre pressures.
CHECK/TIGHTEN TOWING BRACKET FITTINGSINSPECT BRAKE PADS FOR WEAR, CALIPERS
FOR LEAKS AND CONDITION
Check thickness of brake pads, fit new pads if
minimum thickness is less than 3,0mm. Check brake
pads for oil contamination. If new brake pads required.
See BRAKES, Repair, Front Brake Pads
or.See BRAKES, Repair, Rear Brake Pads
WARNING: When renewing brake pads, it
is essential that only genuine components
with correct grade of lining are used.
Always fit new pads as complete axle sets, NEVER
individually or as a single wheel set. Serious
consequences could result from out of balance
braking due to mixing of linings.
Refit road wheels
Fit road wheels in original hub position. Secure in
position with wheel nuts, do not fully tighten wheel
nuts at this stage, lower vehicle and finally tighten
wheel nuts to correct torque.
Alloy wheels:
130 Nm.
Steel wheels:130 Nm.
LUBRICATE ALL HINGES, DOOR CHECK
MECHANISMS, BONNET [HOOD] CATCHES AND
FUEL FILLER FLAP

10MAINTENANCE
4
MAINTENANCE UNDER BONNET [HOOD] MAINTENANCE
CHECK COOLING/HEATER SYSTEMS
Check cooling/heater systems for leaks and hoses for
security and condition.
Cooling system hoses should be changed at first
signs of deterioration.
CHECK CONDITION OF ENGINE MOUNTING
RUBBERS
CHECK BRAKE SERVO HOSE FOR SECURITY
AND CONDITION
CHECK FUEL EVAPORATIVE LOSS CONTROL
SYSTEM FOR LEAKS - V8i CATALYST, Mpi
CHECK FUEL FILLER CAP SEAL FOR LEAKS - V8i
- CATALYST, Mpi
CHECK CONDITION OF HEATER PLUG WIRING
FOR FRAYING, CHAFING AND DETERIORATION -
Tdi
CHECK IGNITION WIRING
Check ignition wiring and high tension leads for
fraying, chafing and deterioration.
CLEAN DISTRIBUTOR CAP - V8i
The electronic ignition employs a Lucas 35DLM8
distributor.
Internal operating parts of distributor are pre-set at
factory and do not normally require resetting.
Adjustments should only be made if unit is known to
be faulty or damaged. Distributor maintenance
consists of following items.
1.Clean outer surfaces of distributor cap to remove
dirt, grease etc.
2.Unclip cap, check cap for cracks.
3.Wipe inside cap with lint free cloth.
4.Check rotor arm, cap and flash shield tracking.
DO NOT DISTURB clear plastic insulating
cover (flash shield) which protects magnetic
pick-up module.
LUBRICATE DISTRIBUTOR ROTOR SPINDLE - V8i
Apply a spot of clean engine oil into rotor spindle after
rotor arm has been removed.
CLEAN/ADJUST SPARK PLUGS - V8i CATALYST
RENEW SPARK PLUGS V8i - V8i CATALYST
Clean, adjust and renew
1.Take great care when fitting spark plugs not to
cross-thread plug, otherwise costly damage to
cylinder head will result.

MAINTENANCE
9
MAINTENANCE
CHECK CONDITION OF DRIVE BELT - V8i - Tdi -
Mpi
RENEW - V8i - Tdi
Renew drive belt V8i.See ENGINE, Repair, Drive
Belt Renew
Renew drive belt Tdi.See ENGINE, Repair, Drive
Belt Renew
RENEW - Mpi
1.Check condition of drive belt, renew a belt that
shows signs of wear, splitting or oil
contamination.
2.Check belt length indicator, belt must be
renewed before indicator reaches R.H. end of
slot.
3.Use 15mm ring wrench on bolt and hold
tensioner pulley fully clockwise.
4.Release drive belt from tensioner pulley and
remove ring wrench.
5.Remove belt from between pulleys.
6.Clean drive belt pulley grooves and ensure
grooves are not damaged.
7.Fit new drive belt around pulley, except
tensioner pulley, ensuring all grooves are
correctly engaged.
8.Hold tensioner pulley fully clockwise and fit drive
centrally around tensioner pulley.
RENEW ANCILLARY DRIVE BELTS
CHECK/TOP UP AUTOMATIC TRANSMISSION
FLUID LEVEL
NOTE: Transmission fluid level is checked
when fluid is cold with engine idling in
neutral.
1.Ensure vehicle is on level ground.
2.Check fluid level registers between MAX and
MIN marking on dipstick.