lock LAND ROVER FREELANDER 2001 Workshop Manual

STEERING
REPAIRS 57-7
25.Remove dust seal from pinion housing.
Refit
1.Fit PAS rack to vehicle from passengers side.
2.Fit dust shield to pinion housing.
3. KV6 models: Fit RH Hydramount.

+ ENGINE - K SERIES KV6, REPAIRS,
Hydramount - engine - RH.
4.Ensure pipe unions are clean.
5.Fit new 'O' rings to fluid pipes.
6.Fit fluid pipes to PAS rack but do not tighten at
this stage.
7.Align fluid pipe bracket to PAS rack, fit bolt but
do not tighten at this stage.
8.With assistance fit PAS rack pinion to steering
column, ensuring column coupling is aligned
with gear input flag.
9.Fit washers and new bolts securing steering
rack mounting to bulkhead, but do not tighten at
this stage. Ensure large washer is fitted to lower
bolt.
10.Fit rubber mount and clamp to PAS rack.
11.Fit bolts securing clamp to bulkhead but do not
tighten at this stage.
12.Tighten PAS rack mounting bolts to 45 Nm (33
lbf.ft).
13.Tighten PAS rack clamp bolts to 45 Nm (33
lbf.ft).
14.Tighten PAS rack fluid feed pipe union to 18
Nm (13 lbf.ft).
15.Tighten PAS rack fluid return pipe union to 22
Nm (16 lbf.ft).
16.Tighten fluid pipe bracket to 10 Nm (7 lbf.ft).
17.Align PAS rack clamp and tighten bolt.
18.Align pipes to clamp fit bolt and tighten to 10
Nm (7 lbf.ft).
19.Fit pinch bolt to steering column and tighten to
32 Nm (24 lbf.ft).
CAUTION: Nuts and bolts must be tightened
with the weight of the vehicle on the
suspension.20.Ensure tapers in track rod end and steering arm
are clean and rubber boot is not damaged.
21.Fit ball joints to steering arms, fit new nuts and
tighten to 55 Nm (40 lbf.ft).
22. KV6 models: Align coolant rail to cylinder
block, fit bolts and tighten to 10 Nm (7 lbf.ft).
23. KV6 models: Position heat shield, fit nuts and
tighten to 25 Nm (18 lbf.ft)
24. Td4 manual models: Align IRD hose 'P' clip fit
bolt and tighten to 25 Nm (18 lbf.ft).
25. Td4 manual models: Align gearchange
linkage to bulkhead, fit bolts and tighten to 25
Nm (18 lbf.ft).
26. Td4 manual models: Connect gear change
rods to gear change linkage.
27. Td4 auto models:Align IRD hose 'P' clip fit bolt
and tighten to 25 Nm (18 lbf.ft).
28.Fit road wheel(s) and tighten nuts to 115 Nm
(85 lbf.ft).
29.Remove stands and lower vehicle.
30.Bleed PAS system.

+ STEERING, ADJUSTMENTS, Power
assisted steering (PAS) system - bleed.
31.Check and adjust front wheel alignment.

+ STEERING, ADJUSTMENTS, Front
wheel alignment - check & adjust.

STEERING
REPAIRS 57-11
Drive belt - K1.8
$% 57.20.02
Remove
1.Disconnect battery earth lead.
2.Turn steering on RH lock.
3.Remove 3 bolts securing RH splash shield to
body and remove shield.
4.Fit a 13 mm spanner to hexagon on belt
tensioner and rotate fully clockwise to release
tension on drive belt.
5.To hold tensioner in this position, fit a suitable
pin, not exceeding 3 mm diameter, through
centre of hexagon into tensioner backplate.
6.Remove and discard drive belt.Refit
1.Clean drive belt pulley grooves and ensure
grooves are not damaged.
2.Fit drive belt. Ensure belt is located correctly in
pulley grooves.
3.Release tension, remove retaining pin and
lower tensioner pulley onto drive belt.
4.Fit splash shield and secure with bolts.
5.Straighten steering.
6.Connect battery earth lead.

STEERING
57-16 REPAIRS
Nacelle - column
$% 57.40.29
Remove
1.Remove key from starter switch.
2.Carefully remove upper half of nacelle. Take
care when releasing clips from lower half of
nacelle.
3.Remove 2 screws securing lower nacelle to
steering column.
4.Lower steering column tilt lever.
5.Carefully remove cover from starter switch
being careful not to damage the passive coil.
6.Carefully pull lower half of nacelle from
retaining clip on column lockRefit
1.Ensure that the steering column tilt lever is
lowered.
2.Position lower half of nacelle and engage with
clip on column lock.
3.Raise column tilt lever.
4.Fit and tighten 2 screws securing lower half of
nacelle to steering column.
5.Fit cover to starter switch.
6.Fit upper half of nacelle and ensure that clips
engage with lower half.

STEERING
REPAIRS 57-17
Column lock & ignition/starter switch
assembly
$% 57.40.31
Remove
1.Disconnect battery earth lead.
2.Remove starter key from ignition lock.
3.Remove steering column nacelle.

+ STEERING, REPAIRS, Nacelle -
column.
4.Disconnect multiplugs from ignition switch and
passive coil.
5.Remove passive coil.
6.Remove 2 screws and remove ignition switch.
7.Move rubber column cover aside to access
column lock bolts.
8.Mark both column lock bolts using a centre
punch.
9.Drill out both column lock bolts.10.Remove column lock saddle and remove
column lock.
11. Models with automatic transmission:
Loosen union and release key interlock cable
from column lock.
Refit
1. Models with automatic transmission: Align
key interlock cable to column lock and tighten
union to 4 Nm (3 lbf.ft).
2.Position lock to steering column assembly and
fit shear bolts. Do not tighten shear bolts at this
stage.
3.Insert starter key, check operation of steering
lock and that key turns freely.
4.Ensure correct operation of key interlock cable.
5.Remove starter key from column lock.
6.Tighten shear bolts fully and shear heads off.
7.Position ignition switch to column, fit and
tighten screws.
8.Fit passive coil.
9.Connect multiplugs to ignition switch and
passive coil.
10. Models with automatic transmission:
Ensure correct operation of microswitch.
11.Align column cover.
12.Fit steering column nacelle.

+ STEERING, REPAIRS, Nacelle -
column.
13.Connect battery earth lead.

STEERING
57-18 REPAIRS
Cable - key interlock
$% 57.40.51
Remove
1.Disconnect battery earth lead.
2.Remove front console.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - front - up to 04MY.
3.Loosen bolt securing cable clamp.
4.Disconnect cable from interlock mechanism.
5.Remove key from starter switch.
6.Remove steering column nacelle.

+ STEERING, REPAIRS, Nacelle -
column.
7.Remove bolt securing steering column height
adjuster lever and remove lever.
NOTE: Thread is left handed.
8.Remove nut securing height adjuster clamp
bolt and remove bolt.
9.Collect plastic stop.10.Loosen union and disconnect cable from
column lock.
11.Release cable from 2 retaining clips.
12.Note the cable routing, manoeuvre cable from
under heater and steering column bracket.
13.Remove cable.

STEERING
REPAIRS 57-19
Refit
1.Position cable, align to heater and steering
column bracket and secure in retaining clips.
2.Align key interlock cable to column lock and
tighten union to 4 Nm (3 lbf.ft).
3.Fit height adjuster clamp bolt and tighten nut to
10 Nm (7.5 lbf.ft). Ensure bolt and plastic stop
are correctly located in slot in column bracket.
4.Fit height adjuster lever and tighten bolt 12 Nm
(9 lbf.ft). Ensure lever is in the fully up position
before tightening bolt. Hold clamp bolt nut to
prevent nut rotation.
5.Connect cable to interlock mechanism.
6.Check key interlock cable adjustment.

+ STEERING, ADJUSTMENTS, Cable
- key interlock - adjust.
7.Fit steering column nacelle.

+ STEERING, REPAIRS, Nacelle -
column.
8.Fit front console.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - front - up to 04MY.
9.Connect battery earth lead.
Column assembly - inner & outer
$% 57.41.01
Remove
1.Disconnect battery earth lead.
2.Remove steering column multi purpose switch.

+ LIGHTING, REPAIRS, Switch -
combined direction indicator/headlight/
horn.
3.Disconnect multiplugs from ignition switch and
passive coil.
4.Remove 2 screws securing steering column
aperture trim and remove trim.

STEERING
57-20 REPAIRS
5.Lower glove lid and remove fuse box cover.
6.Carefully cut 2 harness clips from LH side of
column and release harness.
7.Release 2 harness clips from RH side of
column and release harness.
8. Models with automatic transmission:
Release key interlock cable from column clip.9. Models with automatic transmission:
Loosen union and release key interlock cable
from column lock.
10. Models with automatic transmission:
Remove bolt securing steering column height
adjuster lever and remove lever.
11. Models with automatic transmission:
Remove nut securing height adjuster clamp
bolt and remove bolt.
12. Models with automatic transmission:
Release key interlock cable from steering
column.
13. Models with automatic transmission: Fit
clamp bolt and nut to retain support bracket in
position.

STEERING
REPAIRS 57-21
14.Remove pinch bolt securing steering column to
PAS rack pinion.
15.Remove bolt securing steering column to
fusebox support bracket.
16.Remove 2 nuts and 2 bolts securing steering
column to fascia support rail.
17.Collect snubber.
18.Release steering column from support bracket
and PAS rack pinion.
19.Remove steering column assembly.
20.Remove 2 cable ties from steering column.
21.Remove key interlock cable clip.22.Remove 2 screws securing ignition switch and
remove ignition switch.
23.Remove passive coil.
24.Position steering column assembly in a vice.
25.Centre punch or drill out steering lock shear
bolts.
CAUTION: If steering column is to be re-
used, take care not to deform or damage
column in vice.
26.Remove steering column lock.
CAUTION: Take care not to damage steering
lock body if the lock is to be refitted.

STEERING
57-22 REPAIRS
Refit
1.Remove column from vice.
2.Fit new cable ties to steering column.
3. Models with automatic transmission: Fit key
interlock cable clip.
4.Position steering column to vehicle, locate
steering column on PAS rack, aligning column
coupling with PAS rack input flag.
5.Locate steering column on studs fit nuts but do
not tighten at this stage.
6.Fit bolts and snubber to pivot mountings and
tighten bolts to 14 Nm (10 lbf.ft).
7.Tighten nuts to 14 Nm (10 lbf.ft).
8.Fit and tighten PAS rack pinion clamp bolt to 32
Nm (24 lbf.ft).
CAUTION: Nuts and bolts must be tightened
with weight of vehicle on suspension.
9. Models with automatic transmission:
Remove clamp bolt from height adjuster and
position key interlock cable.
10. Models with automatic transmission: Fit
height adjuster clamp bolt and tighten nut to 10
Nm (7.5 lbf.ft). Ensure bolt and plastic stop are
correctly located in slot in column bracket.
11. Models with automatic transmission: Fit
height adjuster lever and tighten bolt 12 Nm (9
lbf.ft). Ensure lever is in the fully up position
before tightening bolt. Hold clamp bolt nut to
prevent nut rotation.
12. Models with automatic transmission:
Remove starter key from column lock.
13. Models with automatic transmission: Align
key interlock cable to column lock and tighten
union to 4 Nm (3 lbf.ft).
14. Models with automatic
transmission:Position lock to steering column
assembly and fit shear bolts. Do not tighten
shear bolts at this stage.
15. Models with automatic transmission: Insert
starter key, check operation of steering lock
and that key turns freely.
16. Models with automatic transmission:
Ensure correct operation of key interlock cable.
17. Models with automatic transmission:
Remove starter key from column lock.
18. Models with automatic transmission:
Tighten shear bolts fully and shear heads off.
19. Models with automatic transmission: Fit
passive coil.
20. Models with automatic transmission:
Position ignition switch to column, fit and
tighten screws.
21. Models with automatic transmission:
Secure key interlock cable in clip.
22. Models with automatic transmission:
Ensure key interlock cable is correctly fitted.23.Fit side support bolt and tighten to 10 Nm (7.5
lbf.ft).
24.Position harness and secure cable ties.
25.Fit fusebox cover and close glove box lid.
26.Connect multiplugs to column switch and
passive coil.
27.Fit aperture trim and secure with screws.
28. Fit steering column multi purpose switch.

+ LIGHTING, REPAIRS, Switch -
combined direction indicator/headlight/
horn.
29.Connect battery earth lead.

STEERING
REPAIRS 57-25
Steering wheel
$% 57.60.01
Remove
1.Remove airbag module from steering wheel.

+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - steering wheel.
2.Disconnect multiplug from rotary coupler.
3.Centralise steering wheel with road wheels in
straight ahead position.
4.Restrain steering wheel and loosen self locking
nut securing steering wheel to column.
5.Pull steering wheel from column splines.
6.Remove and discard self-locking nut.
7.Remove steering wheel.8.Attach tape across edge of rotary coupler to
retain correct setting.
9. Td4 models: Remove 3 screws securing
damper and remove damper.