lock LAND ROVER FREELANDER 2001 Workshop Manual

EXTERIOR FITTINGS
76-2-8 REPAIRS
Cable/rod - bonnet lock control
$% 76.16.29
Remove
1.Remove bonnet lock.
2.Tie a draw string to end of bonnet release cable
and pull cable from bonnet locking platform.
3.Untie draw string from bonnet release cable.
4.Remove 3 cable ties and release bonnet
release cable from harness.5.Remove bolt securing bonnet release lever to
'A' post lower panel.
6.Remove bonnet release cable from lever and
remove lever.
7.Pull sound insulation away from bulkhead for
access to bonnet release cable grommet.
8.Remove grommet from engine bulkhead.
9.Remove bonnet release cable.

EXTERIOR FITTINGS
REPAIRS 76-2-9
Refit
1.Fit bonnet release cable through bulkhead.
2.Position bonnet release lever and connect
bonnet release cable to lever.
3.Fit release lever to 'A' post and tighten bolt to 9
Nm (7 lbf.ft).
4.Fit bonnet release cable grommet to bulkhead.
5.Position bonnet release cable to main harness
and secure with cable ties.
6.Fit sound insulation to bulkhead.
7.Tie draw string to end of bonnet release cable.
8.Pull draw string to fit bonnet release cable
through bonnet locking platform.
9.Untie draw string from bonnet release cable.
10.Fit bonnet lock.
11.Close bonnet and check for correct locking
operation.

EXTERIOR FITTINGS
76-2-10 REPAIRS
Bumper - assembly - front - up to 04MY
$% 76.22.72
Remove
1.Open bonnet.
2.Remove 8 screws securing wheel arch liners to
bumper, release liners from wheelarch for
access.
3.Remove 2 screws securing bumper valance to
underbelly panel brackets.
4.Remove 3 scrivets securing bumper to
armature.
5.Remove 2 bolts securing rear edge of front
bumper to inner front wing.
6.Remove 4 screws securing bumper to bonnet
locking platform.
7. NAS Models: Release side repeater,
disconnect multiplug and remove repeater.
8.With assistance carefully lift and pull forward
each side of bumper to release bumper side
mounts and clips.
CAUTION: Always protect paintwork when
removing or refitting any body trims or
bumpers.
9.Remove front number plate.
10.Remove badge from grill and discard clips.Refit
1.Fit badge to grill.
2.Fit number plate.
3.With assistance, fit bumper assembly to body.
4. NAS Models: Feed side repeater harness
through bumper, connect multiplug and fit
repeater.
5.Ensure bumper locating pegs are correctly
aligned.
6.Fit and tighten bolts securing bumper to wings.
7.Fit screws securing bumper to bonnet locking
platform.
8.Fit scrivets to armature.
9.Fit screws securing bumper to underbelly
panel.
10.Fit and align wheelarch liners and tighten
screws.
11.Close bonnet.

EXTERIOR FITTINGS
REPAIRS 76-2-11
Bumper - assembly - front - from 04MY
$% 76.22.72
Remove
1.Open bonnet.
2.Remove 8 screws securing wheel arch liners to
bumper, release liners from wheel arch for
access.
3.Remove 4 screws securing bumper valance to
underbelly panel.
4.Remove 3 scrivets securing bumper to
armature.5.Disconnect multiplugs from fog/driving lamps.
6.Remove 2 bolts securing rear edge of front
bumper to inner front wing.
7.Remove 4 screws securing bumper to bonnet
locking platform.
M76 4674

EXTERIOR FITTINGS
76-2-12 REPAIRS
8.With assistance, carefully pull each side of
bumper forward to release it from its
mountings.
CAUTION: Always protect paintwork when
removing or refitting any body trims or
bumpers.
9.Remove front bumper.
NOTE: Do not carry out further dismantling if
component is removed for access only.
10.Remove front number plate.
11.Remove clips securing badge to grille, remove
badge and discard clips.12.Release and remove fog/driving lamp finisher
from bumper.
13.Remove 6 screws securing fog/driving lamps to
bumper.
14.Remove 6 speed nuts from bumper.
Refit
1.Fit 6 speed nuts to bumper.
2.Fit fog/driving lamps to bumper and secure with
screws.
3.Fit fog/driving lamp finishers to bumper.
4.Fit badge to grille.
5.Fit number plate.
6.With assistance, fit bumper assembly to body.
7.Ensure bumper locating pegs are correctly
aligned.
8.Fit and tighten bolts securing bumper to wings.
9.Connect multiplugs to fog/driving lamps.
10.Fit screws securing bumper to bonnet locking
platform.
11.Fit scrivets to armature.
12.Fit screws securing bumper to underbelly
panel.
13.Fit and align wheel arch liners and tighten
screws.
14.Close bonnet.
M76 4677
M76 4679

INTERIOR TRIM COMPONENTS
76-3-14 REPAIRS
Fascia - up to 04MY
$% 76.46.23
Remove
1.Remove front console.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - front - up to 04MY.
2.Remove rotary coupler.

+ RESTRAINT SYSTEMS, REPAIRS,
Rotary coupler - (SRS) air bag system.
3.Disconnect 4 multiplugs from wiper/indicator
switch.
4.Loosen clamping screw and remove wiper/
indicator switch.
5.Remove 2 screws from steering column lower
finisher and remove finisher.6.Open drivers glove box lid and remove fuse box
cover.
7.Disconnect 2 multiplugs from fusebox.
8.Close glove box.
9.Remove clock.

+ INSTRUMENTS, REPAIRS, Clock.
10.Remove both 'A' post upper trim finishers.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
11. Models without passenger airbag: Remove
fascia stowage box.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Stowage box - fascia.
12. Models with passenger airbag: Remove
passenger airbag.

+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - fascia - passenger - up to 04MY.

INTERIOR TRIM COMPONENTS
REPAIRS 76-3-17
26. Models without passenger airbag: Remove 4
nuts from grab handle and remove handle.
27.Remove 4 screws from centre bracket and
remove bracket.28.Remove 4 face level vents and collect seals.
29.Remove glove box hinge pins and remove
glove box lids.
30.Remove glove box lamp and mat.
31.Remove 4 screws from glove box and remove
glove box.
32.Remove 2 screws from each glove box lock and
remove locks.
33.Remove switch blank.
34.Disconnect multiplug from immobilisation ECU.
35.Remove 2 nuts securing immobilisation ECU to
fascia and remove ECU.
36.Remove fascia and coin tray mats.
M76 3995

INTERIOR TRIM COMPONENTS
76-3-18 REPAIRS
Refit
1.Fit fascia and coin tray mats.
2.Fit immobilisation ECU to fascia and secure
with nuts.
3.Connect multiplug to immobilisation ECU.
4.Fit switch blank.
5.Fit glove box locks to fascia and secure with
screws.
6.Fit glove box and secure with screws.
7.Fit glove box lamp and mat.
8.Fit glove box lids and secure hinge pins.
9.Fit face level vents and seals to fascia.
10.Fit centre bracket and secure with screws.
11. Models without passenger airbag: Fit grab
handle and secure with nuts.
12.Fit instrument pack lower cover and secure with
screws.
13.Fit instrument pack to fascia and secure with
screws.
14.Fit fascia harness to fascia and secure with
clips.
15.Connect Lucars to glove box lamp and switch.
16.Connect multiplugs to mirror switch and
headlamp levelling switch.
17.Fit mirror switch and headlamp levelling switch.
18.Connect multiplugs to instrument pack.
19.Fit instrument pack upper cover and secure
with screws.
20.Connect multiplugs to switches on instrument
bezel finisher, fit bezel and secure with screws.
21.With assistance fit fascia to vehicle and secure
with bolts.22.Connect fascia harness multiplugs to main
harness.
23. Models with passenger airbag: Fit passenger
airbag.

+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - fascia - passenger - up to 04MY.
24. Models without passenger airbag: Fit fascia
stowage box.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Stowage box - fascia.
25.Fit 'A' post upper trim finishers.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
26.Fit clock.

+ INSTRUMENTS, REPAIRS, Clock.
27.Open drivers glove box lid and remove fuse box
cover.
28.Connect multiplugs to fusebox.
29.Fit fusebox cover and close glove box lid.
30.Fit steering column lower cover and secure with
screws.
31.Fit wiper/indicator switch and tighten clamping
screw.
32.Connect multiplugs to wiper/indicator switch.
33.Fit rotary coupler.

+ RESTRAINT SYSTEMS, REPAIRS,
Rotary coupler - (SRS) air bag system.
34.Fit front console.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Console - front - up to 04MY.

INTERIOR TRIM COMPONENTS
76-3-20 REPAIRS
10.Disconnect 2 multiplugs from fuse box.
11.Close glove box.
12.Remove clock.

+ INSTRUMENTS, REPAIRS, Clock.
13.Remove hazard warning switch.

+ DRIVER CONTROLS, REPAIRS,
Switch - hazard warning - from 04MY.
14.Remove both 'A' post upper trim finishers.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
15.Remove passenger airbag.

+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - fascia - passenger - from 04MY.
16.Disconnect 2 multiplugs from fascia harness.17.Remove 14 bolts securing fascia.
18.With assistance remove fascia.
NOTE: Do not carry out further dismantling if
component is removed for access only.
19.Disconnect 4 multiplugs from fascia switch
assembly.
20.Remove 4 switches from fascia switch carrier.
M76 4722
M76 4714

INTERIOR TRIM COMPONENTS
76-3-22 REPAIRS
29.Noting fitted position remove fascia harness
assembly.Refit
1.Fit and secure fascia harness.
2.Fit striker plate, secure with screws and adjust
if necessary.
3.Fit passenger side glove box assembly.
4.Fit face level air vents.
5.Fit and secure cruise switch carrier assembly to
fascia.

+ FUEL DELIVERY SYSTEM -
PETROL, REPAIRS, Switch - engagement
(on/off) - from 04MY.
6.Fit glove box lids and secure hinge pins.
7.Connect mirror switch multiplug and fit switch
assembly to fascia.
8.Fit switches to fascia carrier and connect
multiplugs.
9.With assistance fit fascia to vehicle and secure
bolts to 10 Nm (7 lbf.ft).
10.Connect fascia harness multiplugs to main
harness.
11.Fit passenger airbag.

+ RESTRAINT SYSTEMS, REPAIRS,
Air bag - fascia - passenger - from 04MY.
12.Fit 'A' post upper trim finishers.

+ INTERIOR TRIM COMPONENTS,
REPAIRS, Trim finisher - 'A' post - upper -
renew.
13.Fit hazard warning switch.

+ DRIVER CONTROLS, REPAIRS,
Switch - hazard warning - from 04MY.
14.Fit clock.

+ INSTRUMENTS, REPAIRS, Clock.
15.Open drivers side glove box.
16.Fit Radio/CD module.

+ IN CAR ENTERTAINMENT,
REPAIRS, Radio/CD - from 04MY.
17.Fit fuse box cover and close glove box lid.
18.Fit steering column lower cover and secure with
screws.
19.Fit wiper/indicator switch and tighten clamping
screw.
20.Connect multiplugs to wiper/indicator switch.
21.Fit rotary coupler.

+ RESTRAINT SYSTEMS, REPAIRS,
Rotary coupler - (SRS) air bag system.
22.Fit heater control to fascia and secure with
screws.
23.Fit instrument pack.

+ INSTRUMENTS, REPAIRS,
Instrument panel - from 04MY.
M76 4721