lock LAND ROVER FREELANDER 2001 Workshop Manual

DOORS
REPAIRS 76-1-17
3.Remove screw securing door handle
escutcheon to door and remove escutcheon.
4.Remove cover from door pull and remove 3
screws securing door pull to door.
5.Remove screw cover for access to centre
screw and remove 5 screws securing door
pocket to door.6.Release 6 trim studs securing trim casing to
door and remove trim casing.
NOTE: Do not carry out further dismantling if
component is removed for access only.
7.Note fitted position of the long trim stud and
remove 6 trim studs from door trim casing.
8.Remove heat stakes securing door pocket to
trim casing.
NOTE: Heat stake procedure is not used on
early 04 MY vehicles.
9.Remove 4 Torx screws securing door pocket to
trim casing and remove pocket.
10.Remove foam pad from sill button guide.
11.Release retainer and remove sill button guide.
12.Release and remove locking ring securing door
pull to trim casing.
13.Remove 2 plastic rivets securing door pull to
trim casing and remove door pull.
NOTE: Plastic rivets are used for production
purposes only. Screws should be used to retain
all parts previously held in place with plastic
rivets.

DOORS
76-1-18 REPAIRS
Refit
1.Fit door pull to trim casing and secure with
screws and locking ring.
2.Fit sill button guide to trim casing and secure
with retainer.
3.Fit foam pad to sill button guide.
4.Fit door pocket to trim casing and secure with
Torx screws.
5.Fit trim studs to casing.
6.Fit trim casing to door and secure trim studs.
7.Fit screws securing door pull and fit screw
cover.
8.Fit door release handle escutcheon and secure
with screw.
9.Fit screws securing door pocket and fit screw
cover.
10.Position switch pack, connect multiplugs and
secure switch pack to trim casing.
Trim casing - rear door - up to 04MY
$% 76.34.04
Remove
1.Remove screw securing door release
escutcheon and remove escutcheon.
2.Remove 2 screws from door pull.
3.Release 10 trim studs securing trim casing to
door.
4.Disconnect multiplug and remove door trim
casing.
NOTE: Do not carry out further dismantling if
component is removed for access only.

DOORS
REPAIRS 76-1-21
8.Remove locking ring securing tweeter to trim
casing and remove tweeter.
9.Remove foam pad from sill button guide.
10.Release retainer and remove sill button guide.
11.Note the fitted position of the 2 long trim studs
and remove 9 trim studs from trim casing.
12.Release and remove locking ring securing door
pull to trim casing.
13.Remove 2 plastic rivets securing door pull to
trim casing and remove door pull.
NOTE: Plastic rivets are used for production
purposes only. Screws should be used to retain
all parts previously held in place with plastic
rivets.Refit
1.Fit door pull to trim casing and secure with
screws and locking ring.
2.Fit trim studs to casing.
3.Fit sill button guide to trim casing and secure
with retainer.
4.Fit foam pad to sill button guide.
5.Fit tweeter to trim casing and secure with
locking ring.
6.Fit and secure window lift switch and finisher to
trim casing.
7.Connect multiplugs to window lift switch and
door tweeter.
8.Position trim casing, align fasteners with holes
in door and press firmly into position.
9.Fit and tighten screws securing door pull to
door assembly.
10.Fit and secure door pull finisher to door pull.
11.Fit door release escutcheon to trim casing and
secure with screw.

DOORS
76-1-26 REPAIRS
Latch - front door - 3 door
$% 76.37.12
Remove
1.Remove upper plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - upper - 3 door.
2.Release sill button lock rod from door latch.
3.Remove control rod from exterior handle.
4.Disconnect multiplug from latch.
5.Remove 3 Torx screws securing latch to door.
6.On drivers door, release door lock barrel
paddle from latch.
7.Remove latch from aperture.8.Open security flap on latch.
9.Release interior release cable clamp from
latch.
10.Disengage interior release cable from latch.
Refit
1.Secure interior release cable to latch and close
latch security flap.
2.Fit interior release cable clamp to latch.
3.Position latch to door. On drivers door, align
lock barrel paddle to latch.
4.Fit and tighten Torx screws securing latch to
door.
5.Connect multiplug to latch.
6.Connect exterior handle control rod to latch.
7.Fit sill button lock rod to latch.
8.Check operation of latch.
9.Fit plastic sheet to door.

+ DOORS, REPAIRS, Plastic sheet -
front door - upper - 3 door.

DOORS
REPAIRS 76-1-27
Latch - front door - 5 door
$% 76.37.12
Remove
1.Remove front door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - 5 door.
2.Release sill button lock rod from door latch.
3.Release control rod from exterior handle.
4.Disconnect multiplug from latch.
5.Remove 2 screws securing RH glass cable
guide and position guide aside.
6.Remove 3 Torx screws securing latch to door.
7.On drivers door, release door lock barrel
paddle from latch.8.Remove latch from aperture.
9.Open security flap on latch.
10.Release interior release cable clamp from
latch.
11.Disengage interior release cable from latch.
Refit
1.Secure interior release cable to latch and close
latch security flap.
2.Fit interior release cable clamp to latch.
3.Position latch to door. On drivers door, align
lock barrel paddle to latch.
4.Fit and tighten Torx screws securing latch to
door.
5.Position RH glass cable guide and tighten
screws.
6.Connect multiplug to door latch.
7.Connect exterior handle control rod to latch.
8.Fit sill button lock rod to latch.
9.Check operation of door latch.
10.Fit front door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - 5 door.

DOORS
76-1-28 REPAIRS
Latch - rear door
$% 76.37.13
Remove
1.Remove rear door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
rear door.
2.Release exterior handle control rod from latch.
3.Release sill button lock rod from door latch.
4.Disconnect multiplug from latch.
5.Remove 3 Torx screws securing latch to door.
6.Remove latch from aperture.7.Open security flap on latch.
8.Release interior release cable clamp from
latch.
9.Disengage interior release cable from latch.
Refit
1.Secure interior release cable to latch and close
latch security flap.
2.Position latch to door, fit and tighten Torx
screws.
3.Connect multiplug to latch.
4.Connect exterior handle control rod to latch.
5.Fit sill button lock rod to latch.
6.Check operation of latch.
7.Fit rear door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
rear door.

DOORS
REPAIRS 76-1-31
Operating cable - lock remote control - 5
door
$% 76.37.60
Remove
1.Remove door latch.

+ DOORS, REPAIRS, Latch - front
door - 5 door.

+ DOORS, REPAIRS, Latch - rear door.
2.Release cable from interior door release and
remove cable.
Refit
1.Connect cable to interior door release.
2.Fit door latch.

+ DOORS, REPAIRS, Latch - front
door - 5 door.

+ DOORS, REPAIRS, Latch - rear door.
Finisher - rear screen - side - 5 door
$% 76.43.81
Remove
1.Open tail door.
2.Release tail door glass seal from aperture for
access to side finisher fixings.
3.Using a suitable trim stud removal tool, release
3 side finisher fixings from studs on body.
4.Remove side finisher from upper fixing.
5.Remove and discard fixings from finisher.
Refit
1.Fit NEW fixings to finisher.
2.Fit door glass seal to flange.
3.Fit finisher and secure fixings.

DOORS
REPAIRS 76-1-33
Handle - exterior - tail door
$% 76.58.05
Remove
1.Remove tail door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
tail door.
2.Raise glass by clicking latch.
3.Remove 3 nuts securing tail door handle to tail
door.
4.Release handle from tail door.
5.Disconnect 2 Lucars from number plate lamp.
6.Disconnect multiplug and remove handle from
door.7.Collect gasket.
8.Remove nut from lock barrel.
9.Remove lock barrel from handle.
Refit
1.Fit lock barrel to handle.
2.Fit gasket to handle.
3.Position handle and connect Lucars and
multiplug.
4.Fit handle to door and tighten nuts to 5 Nm (3.5
lbf.ft).
5.Fit tail door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
tail door.
6.Reset latch to lower glass.
7.Close door.

DOORS
76-1-34 REPAIRS
Handle - exterior - front door
$% 76.58.07
Remove
1.Remove front door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - 5 door.
2.Release clip securing latch control rod to door
latch and release rod.
3.Remove 3 Torx screws securing door latch,
lower latch and release door lock paddle.
4.Remove grommet to access screw.
5.Remove 2 door handle screw fixings.6.Remove door handle.
7.Remove door latch control rod.
Refit
1.Fit door latch control rod to handle.
2.Position handle to door and tighten securing
screws.
3.Fit grommet to door.
4.Position latch, locate door lock paddle, fit and
tighten Torx screws.
5.Connect control rod to door latch.
6.Fit front door plastic sheet.

+ DOORS, REPAIRS, Plastic sheet -
front door - 5 door.

EXTERIOR FITTINGS
REPAIRS 76-2-5
Mud flap - front
$% 76.10.83
Remove
1.Turn steering wheel to full lock.
2.Remove 3 screws securing mud flap.
3.Remove mud flap.
Refit
1.Position mud flap to body and secure with
screws.
2.Straighten steering.
Mud flap - rear
$% 76.10.85
Remove
1.Remove 3 screws securing mud flap.
2.Remove mud flap.
Refit
1.Position mud flap to body and secure with
screws.