lock LAND ROVER FREELANDER 2001 Owner's Manual

GENERAL DATA
04-2
Lubrication
Type Wet aluminium die-cast sump, pressure fed
Oil filter Disposable canister with full flow by-pass
Oil cooler Integral with oil filter assembly, connected to vehicle cooling system
Oil pump:
⇒ Type Crankshaft driven, eccentric rotor
⇒ Oil flow rate 30 litres / min. (6.625 gallons/min.)
⇒ Outer rotor to body clearance 0.080 - 0.158 mm (0.0031 - 0.062 in.)
⇒ Peak pressure up to 20 bar (290 lbf.in
2)
Oil pressure at idle:
⇒ Cold - 1000 rev/min. 1.5 bar (21.8 lbf.in
2)
⇒ Operating temperature (minimum) 0.5 bar (7.3 lbf.in
2)
⇒ Regulated pressure 4.2 ±0.5 bar (60.9 ± 7.3 lbf.in
2)
⇒ Pressure at 3500 rev/min (hot) 3.0 - 4.5 bar (43.5 - 65.3 lbf.in
2)
Relief valve opening pressure 4.2 bar (60.9 lbf.in
2)
Low oil pressure switch opening pressure 0.2 - 0.5 bar (2.9 - 7.3 lbf.in
2)
Cylinder block
Type Grey cast iron with hollow beam structure
Cylinder head warp - maximum 0.03 mm (0.001 in.)
Cylinder head bore:
†
⇒ Standard 84.000 - 84.018 mm (3.3071 - 3.3078 in)
⇒⇒ Wear limit 84.040 mm (3.3087 in)
⇒ Intermediate 84.080 - 84.098 mm (3.3102 - 3.3109 in)
⇒⇒ Wear limit 84.120 mm (3.3118)
⇒ 1st.Oversize (Grinding dimension) 84.250 - 84.268 mm (3.3169 - 3.3176 in)
⇒⇒ Wear limit 84.290 mm (3.3185 in)
Cylinder bore ovality (permitted roundness deviation)
†0.01 mm (0.0004 in)
⇒ Wear limit 0.04 mm (0.0016 in)
Cylinder bore taper (permitted conicity)
†0.01 mm (0.0004 in)
⇒ Wear limit 0.04 mm (0.0016 in)
†Measurements at top centre and bottom of bore
Crankshaft
Main journal diameter 60 mm (2.36 in.)
Crankpin journal diameter 44.975 - 45.009 mm (1.7707 - 1.7720 in)
End float 0.08 - 0.163 mm (0.0031 - 0.0064 in.)
Maximum out of round
†0.15 mm (0.006 in.)
Crankshaft seal PTFE
†At centre main journal; crankshaft supported on outer bearing pins

GENERAL DATA
04-6
Engine - K1.8 Petrol
General
Type 1.8 litre petrol, 16-valve DOHC
Cylinder arrangement 4 in-line, transverse, No.1 cylinder at front of engine
Bore 80.00 mm (3.150 in.)
Stroke 89.30 mm (3.516 in.)
Capacity 1796 cm
3 (109.59 in3)
Firing order 1-3-4-2
Compression ratio 10.5 :1 ± 0.5 :1
Direction of rotation Clockwise viewed from the front of the engine
Maximum power 88 kW (118 bhp) @ 5500 rev/min.
Maximum torque 165 Nm (223.7 lbf.ft) @ 2750 rev/min.
Idle speed 775 ± 50 rev/min.
Maximum intermittent engine speed 6750 rev/min.
Weight (fully dressed, wet) 108 kg (238 lb)
Dimensions:
⇒ Length (nominal) 654 mm (25.75 in.)
⇒ Width (nominal) 600 mm (23.62 in.)
⇒ Height (nominal) 615 mm (24.21 in.)
Spark plugs:
⇒ Type NLP 100290
⇒ Gap 1.0 mm ± 0.05 mm (0.039 in. ± 0.002 in.)
Ignition coils:
⇒ Make Nippon Denso - NEC 100730
⇒ Type 2 x twin output coils, plug top mounted; cylinders 1 & 4 and 2 & 3
⇒ Primary resistance (typical) 0.7 Ω
⇒ Secondary resistance (typical) 10 Ω
Fuel injection system:
Type Returnless fuel rail, multi-point fuel injection, electronically controlled
from ECM
Controller MEMS 3 breakerless, electronic, fully mapped engine management
system
Injectors:
⇒ Operating pressure 3.5 bar (50.8 lbf.in
2)
⇒ Fuel flow rate 117 g/min. @ 3.0 bar (4.13 fl.oz/min. @ 43.5 lbf. in
2)
Valve operation Self-adjusting, lightweight hydraulic tappets operated directly by
camshafts
Emissions standard ECD3
Cylinder block:
Material Aluminium alloy
Cylinder liner type Damp, bottom half stepped - sliding fit into lower part of cylinder block
Cylinder liner bore:
⇒ RED grade A 80.000 - 80.015 mm (3.1496 - 3.1501 in.)
⇒ BLUE grade B 80.016 - 80.030 mm (3.1502 - 3.1508 in.)

GENERAL DATA
04-11
Engine - KV6 Petrol
General
Type:
⇒ Up to 03 Model Year
⇒ From 03 Model Year2.5 litre V6, 24 valve, air assisted direct fuel injection petrol, water
cooled, transverse mounted
2.5 litre V6, 24 valve, direct fuel injection petrol, water cooled,
transverse mounted
Cylinder arrangement: 90° V6, numbered from the front of the engine
⇒ Left bank Cylinders 1, 3 and 5
⇒ Right bank Cylinders 2, 4 and 6
Bore (nominal) 80 mm (3.15 in.)
Stroke 82.8 mm (3.26 in.)
Capacity 2497 cm
3 (152.37 in3)
Firing order 1-6-5-4-3-2
Compression ratio 10.5 : 1 ± 0.5 : 1
Direction of rotation Clockwise viewed from front of engine
Maximum power 130 kW (177 bhp) @ 6500 rev/min.
Maximum torque 240.0 Nm (177 lbf.ft) @ 4000 rev/min.
Maximum engine speed:
⇒ Continuous 6500 rev/min.
⇒ Intermittent 6750 rev/min.
Idle speed 750 rev/min. ± 50 rev/min.
Weight (fully dressed, wet) 154 kg (340 lb)
Dimensions (dressed):
⇒ Length (nominal) 770 mm (30.3 in.)
⇒ Width (nominal) 750 mm (29.5 in.)
⇒ Height (nominal) 750 mm (29.5 in.)
Valve operation Self-adjusting lightweight hydraulic tappets operated directly by the
camshafts
Fuel injection system:
⇒ Make - Up to 03 Model Year
⇒ Make - From 03 Model YearSiemens engine management system
Siemens engine management system
⇒ Type - Up to 03 Model Year
⇒ Type - From 03 Model YearMulti-point, air assisted fuel injection controlled by ECM, electro-
mechanical injectors with twin sprays targeted on to back of inlet
valves
Multi-point fuel injection controlled by ECM, electro-mechanical
injectors with quadruple sprays targeted on to back of inlet valves
Inlet manifold Variable geometry
Spark plugs
⇒ Type
⇒ Plug gapNLP 100290
1.0 mm ± 0.05 mm (0.039 in. ± 0.002 in.)
Coils:
⇒ Make - Up to 03 Model Year
⇒ Make - From 03 Model Year
⇒ Type - Up to 03 Model Year
⇒ Type - From 03 Model YearBREMR
Champion BAE 403H
6 x coils (3 x plug top, 3 x remote mounted)
6 x coils (6 x plug top)
Emissions standard ECD3

GENERAL DATA
04-12
Cylinder head
Type Aluminium alloy
Cylinder head gasket * Multi-layer steel
Cylinder head warp:
⇒ Lateral
⇒ Longitudinal0.025 mm (0.001 in)
0.2 mm (0.08 in)
Cylinder head height
Reface height - minimum118.95 - 119.05 mm (4.683 - 4.687 in)
118.95 mm (4.683 in)
Cylinder block
Type Cosworth cast aluminium alloy with bearing ladder bolted to bottom of
block
Cylinder liner type Damp, bottom half stepped - sliding fit into lower part of cylinder block
Cylinder liner bore:
⇒ RED grade A 80.000 - 80.015 mm (3.1496 - 3.1502 in.)
⇒ BLUE grade B 80.015 - 80.030 mm (3.1502 - 3.1508 in.)
Crankshaft
Material / Type Cast spheroidal graphite iron with cold rolled fillets on all journals
except outer mains
Crankshaft end-float
⇒ Service limit0.10 - 0.30 mm (0.004 - 0.012 in.)
0.40 mm (0.016 in.)
Main journal diameter:
⇒ Grade 1 67.743 - 67.749 mm (2.6670 - 2.6673 in.)
⇒⇒ Grade A (Green)
†
⇒⇒ Grade B (Yellow)†
⇒⇒ Grade C (Black)†
⇒ Grade 2 67.737 - 67.743 mm (2.6668 - 2.6670 in.)
⇒⇒ Grade A (Blue)
†
⇒⇒ Grade B (Green)†
⇒⇒ Grade C (Yellow)†
⇒ Grade 3 67.731 - 67.737 mm (2.6666 - 2.6668 in.)
⇒⇒ Grade A (Red)
†
⇒⇒ Grade B (Blue)†
⇒⇒ Grade C (Green)†
Maximum out of round 0.010 mm (0.0004 in.)
Main housing diameter:
⇒ Grade A 71.600 - 71.593 mm (2.8189 - 2.8186 in.)
⇒ Grade B 71.593 - 71.586 mm (2.8186 - 2.8183 in.)
⇒ Grade C 71.586 - 71.579 mm (2.8183 - 2.8181 in.)
Big-end journal diameter:
⇒ Grade A 54.049 - 54.055 mm (2.1279 - 2.1281 in.)
⇒ Grade B 54.043 - 54.049 mm (2.1277 - 2.1279 in.)
⇒ Grade C 54.037 - 54.043 mm (2.1274 - 2.1277 in.)
⇒ Maximum out of round 0.010 mm (0.0004 in.)
Big-end housing diameter:
⇒ Grade 7 57.677 - 57.671 mm (2.2707 - 2.2705 in.)
⇒⇒ Grade A (Green)
*
⇒⇒ Grade B (Blue)*
⇒⇒ Grade C (Red)*
⇒ Grade 8 57.671 - 57.665 mm (2.2705 - 2.2703 in.)
⇒⇒ Grade A (Yellow)
*
⇒⇒ Grade B (Green)*
General

GENERAL DATA
04-13
⇒⇒ Grade C (Blue)*
⇒ Grade 9 57.665 - 57.659 mm (2.2703 - 2.2700 in.)
⇒⇒ Grade A (Black)
*
⇒⇒ Grade B (Yellow)*
⇒⇒ Grade C (Green)*
†
Cylinder block / bearing ladder bore diameter grades* Crankshaft big-end journal grades
Main bearings
Quantity 4
Material / type Glacier AS15 - oil grooves in upper half shells, plain lower half shells
Clearance in bearings 0.021 - 0.039 mm (0.0008 - 0.0015 in.)
Thrust washers:
⇒ Type / position Glacier AS15 - thrust washer halves at top and bottom of rear main
bearing, oil grooves in top and bottom halves
⇒ Thrust washer halves thickness 2.61 - 2.65 mm (0.103 - 0.104 in.)
Main bearing thickness:
⇒ Red 1.930 - 1.927 mm (0.0760 - 0.0759 in.)
⇒ Blue 1.927 - 1.924 mm (0.0759 - 0.0757 in.)
⇒ Green 1.924 - 1.921 mm (0.0757 - 0.0756 in.)
⇒ Yellow 1.921 - 1.918 mm (0.0756 - 0.0755 in.)
⇒ Black 1.918 - 1.915 mm (0.0755 - 0.0754 in.)
Big-end bearings
Material / Type Glacier AS15 - plain upper and lower half shells with locating tags
Clearance in bearings 0.022 - 0.040 mm (0.0009 - 0.0016 in.)
Big-end bearing thicknesses:
⇒ Red 1.803 - 1.800 mm (0.0710 - 0.0709 in.)
⇒ Blue 1.800 - 1.797 mm (0.0709 - 0.0707 in.)
⇒ Green 1.797 - 1.794 mm (0.0707 - 0.0706 in.)
⇒ Yellow 1.794 - 1.791 mm (0.0706 - 0.0705 in.)
⇒ Black 1.791 - 1.788 mm (0.0705 - 0.0704 in.)
Big-end end-float 0.19 - 0.29 mm (0.007 - 0.011 in.)
Connecting rods
Type Forged steel H-sections with horizontally split big-ends
Distance between centres 151.31 - 151.41 mm (5.957 - 5.961 in.)
Gudgeon pins
Type Semi-floating offset towards thrust side
Fit in connecting rods Interference
⇒ Diameter - Red coded 17.997 - 18.000 mm (0.7085 - 0.7087 in.)
⇒ Diameter - Green coded 17.994 - 17.997 mm (0.7084 - 0.7085 in.)
⇒ Length 52.3 - 52.6 mm (2.059 - 2.071 in.)
⇒ Clearance in piston 0.011 mm (0.0004 in.)
Pistons
Type Aluminium alloy, tin plated, thermal expansion with offset gudgeon pin
Piston diameter (at right angle to gudgeon pin and 10
mm (0.4 in. from bottom of skirt):
⇒ Grade A 79.965 - 79.980 mm (3.1482 - 3.1488 in.)
⇒ Grade B 79.981 - 79.995 mm (3.1489 - 3.1494 in.) General

GENERAL DATA
04-22
Manual Gearbox - PG1
Gear ratios:
⇒ First 3.250 : 1 (19.902 : 1 overall)
⇒ Second 1.894 : 1 (11.598 : 1 overall)
⇒ Third 1.222 : 1 (7.483 : 1 overall)
⇒ Fourth 0.848 : 1 (5.019 : 1 overall)
⇒ Fifth 0.649 : 1 (3.974 : 1 overall)
⇒ Reverse 3.000 : 1
Reverse idler gear to selector fork clearance 0.5 to 1.1 mm (0.020 - 0.043 in)
Selector fork prong width 13.0 to 13.3 mm (0.512 - 0.524 in)
Selector fork groove to pin clearance:
⇒ Standard 0.05 to 0.35 mm (0.002 - 0.014 in)
⇒ Service limit 0.50 mm (0.020 in)
Selector fork groove width 7.05 to 7.25 mm (0.278 - 0.285 in)
Gearshift arm to guide clearance:
⇒ Standard 0.20 to 0.30 mm (0.008 - 0.012 in)
⇒ Service limit 0.55 mm (0.022 in)
Interlock shift guide groove width 8.10 to 8.20 mm (0.319 - 0.323 in)
Synchro ring to gear clearance:
⇒ Standard 0.85 to 1.10 mm (0.033 - 0.043 in)
⇒ Service limit (minimum clearance) 0.40 mm (0.016 in)
Selector shaft forks in synchro sleeve grooves
clearance:
⇒ Standard 0.45 to 0.65 mm (0.018 - 0.026 in)
⇒ Service limit 1.00 mm (0.039 in)
Gearshift arm guide to selector fork clearance:
⇒ Standard 0.20 to 0.50 mm (0.008 - 0.020 in)
⇒ Service limit 0.80 mm (0.031 in)
Gearshift arm guide tongue width 11.90 to 12.00 mm (0.469 - 0.472 in)
Gearshift arm guide to interlock assembly clearance:
⇒ Standard 0.05 to 0.35 mm (0.002 - 0.014 in)
⇒ Service limit 0.60 mm (0.024 in)
Gearshift arm guide groove width 13.05 to 13.25 mm (0.514 - 0.522 in)
Interlock ball to gearshift arm guide clearance:
⇒ Standard 0.05 to 0.25 mm (0.002 - 0.010 in)
⇒ Service limit 0.50 mm (0.020 in)
Interlock ball outside diameter 12.05 to 12.15 mm (0.474 - 0.478 in)
2nd to 3rd gear clearance:
⇒ Standard 0.06 to 0.21 mm (0.002 - 0.008 in)
⇒ Service limit 0.30 mm (0.012 in)
3rd gear thickness:
⇒ Standard 35.42 to 35.47 mm (1.394 - 1.396 in)
⇒ Service limit 35.30 mm (1.390 in)

GENERAL DATA
04-25
Automatic Gearbox - Jatco
Gear Ratios - Td4 engine:
⇒ First 3.801:1
⇒ Second 2.131:1
⇒ Third 1.364:1
⇒ Fourth 0.935:1
⇒ Fifth 0.685:1
⇒ Reverse 2.970:1
Gear ratios - KV6 engine
⇒ First 3.474 : 1
⇒ Second 1.948 : 1
⇒ Third 1.247 : 1
⇒ Fourth 0.854 : 1
⇒ Fifth 0.685 : 1
⇒ Reverse 2.714 : 1
Final drive ratio:
⇒ Td4 engine
⇒ KV6 engine2.91 : 1
3.66 : 1
Torque converter lock-up
Td4
KV6Engaged in fourth and fifth gears.
50% throttle - 80 Kph (50 mph) in normal drive mode
50% throttle - 110 Kph (69 mph) in normal drive mode

GENERAL DATA
04-27
Steering
* The steering geometry settings are given in degrees and minutes, decimal parts of a degree and millimetres.
Steering and suspension geometry settings are for a vehicle at unladen weight.
Type Power assisted rack and pinion
Steering column Height adjustable by 3.5° or 30 mm vertical movement of steering
wheel
Turns - lock to lock 3.20
Turning circle: 11.38 m (37 ft 1.2 in) - with a 215/65 tyre
Overall ratio 19.5: 1
Wheel alignment*
Front
⇒ Camber angle (negative): -0° 15' ± 0° 45' (-0.25° ± 0.75°)
⇒ Cross camber angle 1° (1°) Maximum
⇒ Castor angle: 3° 30' ± 1° (3.92° ± 1.0°)
⇒ Cross castor angle 1° (1°) Maximum
⇒ King pin inclination 12° 18' (12.3°)
⇒ Front wheel alignment - total toe-out: - 0° 14' ± 0° 14' (- 0.23° ± 0.23°)
Rear
⇒ Camber angle (negative): -0° 30' ± 0° 45' (0.5° ± 0.75°)
⇒ Cross camber angle 1° (1°) Maximum
⇒ Thrust angle: 0° 0' ± 0° 6' (0° ± 0.10°)
⇒ Rear wheel alignment - total toe-in: 0° 20' ± 0° 15' (0.3° ± 0.25°)
Power assisted steering
Maximum Operating Pressure ( limited by pressure
relief valve in pump):
⇒ K1.8 90 - 100 bar (1305 - 1450 lbf/in
2)
⇒ KV6 & Td4 90 - 100 bar (1305 - 1450 lbf/in
2)
Pressure at idle 5 - 7 bar (72.5 - 101.5 lbf/in
2)
Maximum flow 5.5 ± 0.5 litres/min. (1.45 ± 0.13 US gal/min), limited by flow control
valve in pump

GENERAL DATA
04-31
Brakes
Front disc brakes
Type Pin-slider caliper with ventilated disc, self-adjusting
Disc diameter 262 mm (10.31 in)
Disc thickness:
⇒ New
⇒ Service limit20.8 - 21.00 mm (0.818 - 0.826 in)
18.00 mm (0.708 in)
Disc run-out (maximum) 0.040 mm (0.0016 in), with wheel on
Pad minimum thickness 3.00 mm (0.118 in)
Rear drum brakes
Drum inside diameter 254 mm (10.00 in)
Drum wear limit 255.49 mm (10.059 in), discard drum
Lining minimum thickness 2.00 mm (0.079 in)
Drum ovality limit 0.012 mm (0.0005 in)
Master cylinder
Bore diameter 23.80 mm (0.937 in)
Brake servo
Servo boost ratio 4.5 : 1
Parking brake
Type Mechanically operated via twin cables on rear drum brakes
Anti-lock braking system
Circuit type Diagonal split, dual circuit, 4-sensor ABS
ABS type TEVES MK20 with ABS, Hill Descent Control (HDC), Electronic
Traction Control (ETC) and Electronic Brakeforce Distribution (EBD)

IDENTIFICATION NUMBERS
05-2
Vehicle identification number -
Example: SALLNABG11A518779
Paint and trim colour codes
Paint code (F): a 3 digit code identifying the original
paint colour is stamped on the VIN plate.
Trim code (G):a code identifying the original trim
type and colour is stamped on the VIN plate.
Identification Number Locations
Engine number
K1.8 engine serial number is stamped on the front
face of the cylinder block adjacent to the gearbox.
K1.8 engines
KV6 engine serial number is stamped on the rear LH
side of the LH cylinder block.
KV6 engines
Td4 engine serial number is stamped on the bottom
LH side of the cylinder block.SALManufacturer's identifier (Land Rover UK)
LNMarque/Model
LN = Freelander
ATrim level
A = Trim level 1
BBody Style
B = 5 door models
GEngine
G = KV6 petrol engine models
1Transmission and Steering
1 = RHD automatic gearbox
1Model Year
1 = 2001 Model year
2 = 2002 Model year
3 = 2003 Model year
AAssembly plant
A = Solihull
6 figures= Serial number