sensor LAND ROVER FRELANDER 2 2006 Owner's Manual

DT C
Description Possible Cause Action
modul e (TCM) fault General Procedures ).
Cal ibrat e t he gear pos it ion sens or us i ng the
approved di agnos ti c s ys t em. Refer to the
warrant y poli cy and procedures manual if t he
TCM is sus pect .
P0709-00
Trans mis s ion range sens or
A circui t int ermi tt ent Incorrect adjus tment of t he
gear s elector lever cabl e Incorrect adjus tment of t he
gear posi ti on s ens or Int ernal t rans mi ss i on cont rol
modul e (TCM) fault P0711-00
Trans mis s ion flui d
temperature s ens or A
circuit range/performance Transmis si on fluid
temperat ure s ens or ci rcuit :
hi gh res is t ance i n t ermi nal s Transmis si on fluid
temperat ure s ens or fault Check t he transmis s ion fluid temperat ure
sens or and ci rcuit s. Refer to t he elect rical
gui des . Recti fy as necess ary.
P0712-00 Trans mis s ion flui d
temperature s ens or A
circuit l ow Transmis si on fluid
temperat ure s ens or ci rcuit :
short ci rcuit t o ground Transmis si on fluid
temperat ure s ens or ci rcuit :
open circui t P0713-00
Trans mis s ion flui d
temperature s ens or A
circuit hi gh Transmis si on fluid
temperat ure s ens or ci rcuit :
short ci rcuit t o power P0715-00
Turbine/Input shaft speed
(ISS) s ens or A circui t Transmis si on ISS ci rcuit :
short ci rcuit t o power Check t he transmis s ion ISS s ens or and circuit s .
Refer to the el ect ri cal guides . Ins tal l a new ISS
sens or as neces sary. For addit ional i nformati on,
refer t o: (307-01 Aut omati c
Transmis s ion/Trans axle)
Input Shaft Speed (ISS) Sensor - I6 3.2L Pet rol (Removal and Ins t al lat ion),
Input Shaft Speed (ISS) Sensor - TD4 2.2L Di esel (Removal and Ins t allat ion).
P0716-00
Turbine/Input shaft speed
(ISS) s ens or A circui t
range/performance Transmis si on ISS s ens or
ci rcuit : high res i st ance in
terminals Transmis si on ISS s ens or fault
P0718-00
Turbine/input shaft speed
(ISS) s ens or A circui t
int ermi tt ent Transmis si on ISS s ens or
ci rcuit : int ermi tt ent hi gh
res is tance in terminals Transmis si on ISS s ens or fault
P0720-00
Output s haft s peed (OSS)
s ens or circuit (vehi cle
s peed s ens or A circuit ) OSS s ens or ci rcuit : s hort
ci rcuit t o power Check t he transmis s ion OSS s ens or and circui ts .
Refer to the el ect ri cal guides . Rect ify as
neces sary.
P0721-00 Output s haft s peed (OSS)
s ens or circuit (vehi cle
s peed s ens or A circuit )
range/performance The wheel radi us does not
agree wit h t he wheel radius
programmed in t he car
confi gurati on fi le OSS s ens or not ins tall ed
correctl y OSS s ens or ci rcuit : high
res is tance in terminals OSS s ens or fault Check t hat t he correct wheels and ti res are
ins tall ed. Check t he transmis si on OSS s ensor
for correct ins t al lat ion. Check t he OSS s ensor
and ci rcuit s. Refer to t he elect rical guides.
Rect ify as neces s ary.
P0722-00 Output s haft s peed (OSS)
s ens or circuit (vehi cle
s peed s ens or A circuit ) no
s ignal OSS s ens or ci rcuit : high
res is tance in terminals OSS s ens or ci rcuit : open
ci rcuit OSS s ens or ci rcuit : s hort
ci rcuit t o ground OSS s ens or fault
Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Check t he transmis s ion OSS s ens or and circui ts .
Refer to the el ect ri cal guides . Rect ify as
neces sary. Refer t o t he warranty pol icy and
procedures manual if t he TCM is s us pect.
P0723-00 Output s haft s peed (OSS)
s ens or circuit (vehi cle
s peed s ens or A circuit )
int ermi tt ent OSS s ens or not ins tall ed
correctl y OSS s ens or ci rcuit :
intermit t ent hi gh res is t ance
in t ermi nals OSS s ens or fault
Int ernal t rans mi ss i on cont rol
modul e (TCM) fault Check t he transmis s ion OSS s ens or for correct
ins tall ati on. Check the OSS s ens or and circuit s .
Refer to the el ect ri cal guides . Rect ify as
neces sary. Refer t o t he warranty pol icy and
procedures manual if t he TCM is s us pect.
P0725-00 Engi ne s peed input ci rcuit Cont roll er area network
(CAN) circui t: open circui t CAN circuit : s hort circui t to
ground CAN module fault Carry out a compl ete vehicle read for CAN
relat ed DTCs. Recti fy as neces sary.
P0729-00 Gear 6 incorrect rati o Cont act resi s tance in the
terminals Sol enoi d regulat ing
incorrectl y Mechanical fault i n
trans mi ss i on - transmis s ion
component s worn and Carry out a compl ete read for related engi ne
torque DTCs . Check trans mi ss i on fl uid l evel and
condit ion. Refer t o the warrant y poli cy and
procedures manual if t he t rans mis s ion i s
sus pect .

DT C
Description Possible Cause Action
(SLC2) ci rcuit : short ci rcuit t o
power
C2 Pres sure cont rol s olenoid
(SLC2) fault P0970-00
Pres s ure control s olenoid C
cont rol circui t low C2 Pres sure cont rol s olenoid
(SLC2) ci rcuit : short ci rcuit t o
ground C2 Pres sure cont rol s olenoid
(SLC2) ci rcuit : open ci rcuit C2 Pres sure cont rol s olenoid
(SLC2) fault P0971-00
Pres s ure control s olenoid C
cont rol circui t hi gh C2 Pres sure cont rol s olenoid
(SLC2) ci rcuit : short ci rcuit t o
power C2 Pres sure cont rol s olenoid
(SLC2) fault P0973-00
Shift sol enoid A control
circuit l ow Shi ft s olenoid No. 1 ci rcuit :
short ci rcuit t o ground Shi ft s olenoid No. 1 ci rcuit :
open circui t Shi ft s olenoid No. 1 fault Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion is s us pect.
P0974-00 Shift sol enoid A control
circuit hi gh Shi ft s olenoid No. 1 ci rcuit :
short ci rcuit t o power Shi ft s olenoid No. 1 fault
P0976-00
Shift sol enoid B control
circuit l ow Shi ft s olenoid No. 2 ci rcuit :
short ci rcuit t o ground Shi ft s olenoid No. 2 ci rcuit :
open circui t Shi ft s olenoid No. 2 fault Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion is s us pect.
P0977-00 Shift sol enoid B control
circuit hi gh Shi ft s olenoid No. 2 ci rcuit :
short ci rcuit t o power Shi ft s olenoid No. 2 fault
P1783-68
Trans mis s ion
overtemperat ure condit ion Transmis si on fluid level l ow Transmis si on fluid
cooler/hos es are
obs t ructed/damaged/blocked. Mechanical fault i n the
trans mi ss i on The trans mi ss i on has been
expos ed to hi gh load and
hi gh ambient t emperature. Check t he transmis s ion fluid level and
condit ion. Check t he t rans mis s ion flui d cool er
/hos es for s igns of obst ruct ion/damage
/blockage. Recti fy as necess ary. Refer t o t he
warrant y poli cy and procedures manual if t he
trans mi s si on is sus pect .
P1799-00 Cont rol ler area net work
(CAN) t rans mi ss ion cont rol
module ( TCM)/ant i-lock
brake s yst em (ABS) circuit
malfunct ion CAN circuit fault (bet ween
ABS modul e (brake cont rol
modul e(BCM)) and TCM ABS (BCM) module fault Check t he CAN circui ts . Refer t o t he electrical
gui des . Recti fy as necess ary. Refer t o t he
warrant y poli cy and procedures manual if t he
ABS module (BCM) is sus pect .
P2158-00 Vehi cle Speed Sens or B
(i nput s haft s peed s ens or
(ISS)) ISS s ensor circui t: s hort
ci rcuit t o ground ISS s ensor circui t: s hort
ci rcuit t o power ISS s ensor circui t: open
ci rcuit ISS s ensor faul t Check t he ISS sens or and ci rcuit s. Refer to t he
el ect ri cal guides . Ins t al l a new ISS s ens or as
neces sary.
For addit ional informati on, refer t o: Input Shaft Speed (ISS) Sensor - I6 3.2L Pet rol (307-01
Aut omati c Trans mis s ion/Transaxle, Removal
and Ins tal lati on) /
Input Shaft Speed (ISS) Sens or - TD4 2.2L Dies el (307-01 Aut omat ic
Transmis s ion/Trans axle, Removal and
Ins tal lati on).
P2719-00 Pres s ure control s olenoid D
cont rol circui t
range/performance Press ure cont rol s olenoid
(SLC3) ci rcuit : short ci rcuit t o
ground Press ure cont rol s olenoid
(SLC3) ci rcuit : open ci rcuit Press ure cont rol s olenoid
(SLC3) ci rcuit : short ci rcuit t o
power Press ure cont rol s olenoid
(SLC3) fault Refer to the warrant y pol icy and procedures
manual i f the t rans mis s ion is s us pect.
P2720-00 Pres s ure control s olenoid D
cont rol circui t low Press ure cont rol s olenoid
(SLC3) ci rcuit : short ci rcuit t o
ground Press ure cont rol s olenoid
(SLC3) ci rcuit : open ci rcuit Press ure cont rol s olenoid
(SLC3) fault

1. Check for free play i n all s uspens ion and body mounti ng rubbers .
2. Check condit ion of s uspens ion rubber boot s and gait ers .
Fuel System
Check fuel sys tem pipes , hos es and unions for chafi ng, l eaks and corros ion.
Electrical Harnesses
Check al l el ect ri cal harnes s es for chafing.
Oil/Fluid Leaks
Check for oil/fluid leaks .
Power Steering
Check power s teering rod bal l joi nt fixi ngs , gait ers and condi ti on of bal l joi nt s and dus t covers .Check power s teering pipes , hos es and unions for chafi ng, leaks and corros ion.
Exhaust System
Check exhaust s ys tem for l eaks , securi ty and damage.
Fault Lamp(s)
If fault l amp(s ) are ill uminat ed, t est the as s oci at ed s yst em us i ng T4 and report findings .
Road Test
Carry out road t est of vehicle.For addit ional informat ion, refer t o: Road/Roller Tes ti ng (100-00 General Informati on, Des cri pt ion and Operati on).
General
Endors e Service Record.Report any unus ual features of vehi cl e condi ti on and any addi ti onal work required.
Vehicles Operating Under Arduous Conditions
Service i ntervals for vehi cles operati ng under arduous condi ti ons are det ailed bel ow.
Braking system
CAUTION: When vehicles are operating under arduous conditions, the following service items must be carriedout every 3 months or 3,750 miles (6,000 km).
Ins pect front brake pads for wear.Ins pect rear pads for wear.Check brake cal ipers for s igns of fl ui d l eaks .Check brake dis cs for condi ti on.Check al l brake boos t er and brake s ys t em pipes and hos es for condi ti on, chafi ng and leaks.Clean road wheel hub s pigot s and appl y greas e, Land Rover Part Number RY L 105020 t o t he wheel mat ing surfaceof each s pigot .
Brake Fluid Replacement
CAUTION: When vehicles are operating under arduous conditions, the following service item must be carried outevery 2 Years or 30,000 miles (48,000 km).
Replace brake fluid.
Road Wheel Speed Sensors
CAUTION: When vehicles are operating under arduous conditions, the following service item must be carried outevery 3 months or 3,750 miles (6,000 km).
Ins pect the road wheel s peed s ens or harness es for damage.
Engine Oil and Filter
CAUTION: When vehicles are operating under arduous conditions, the following service item must be carried outevery 3 months or 3,750 miles (6,000 km).
Renew engi ne oil and fil ter.

Ins pect rear pads for wear.
Check brake cal ipers for s igns of fl ui d l eaks .
Check brake dis cs for condi ti on.
Check al l brake boos t er and brake s ys t em pipes and hos es for condi ti on, chafi ng and
leaks.Clean road wheel hub s pigot s and appl y greas e, Land Rover Part Number RY L 105020 t o
t he wheel mat ing surface
of each s pigot . Brake Fluid Replacement
CAUTION:
When vehicles are operating under arduous conditions, the following service item mus t be carried out
every 2 Years or 30,000 miles (48,000 km).
Replace brake fluid. Road Wheel Speed Sensors
CAUTION:
When vehicles are operating under arduous conditions, the following service item mus t be carried out
every 3 months or 3,750 miles (6,000 km).
Ins pect the road wheel s peed s ens or harness es for damage. Engine Oil and Filter
• CAUTIO NS:
When vehicles are operating under arduous conditions, the following service item mus t be carried out every 3
months or 3,750 miles (6,000 km).
Vehicles operating on high sulphur content fuel - above 0.7%, the oil and filter cha nge period MUST NOT
exceed 3 months or 3,750 miles (6,000 km).
Vehicles operating on moderate sulphur content fuel - 0.3 to 0.7%, the oil and filte r change period MUST NOT
exceed 6 months or 7,500 miles (12,000 km).
Renew engi ne oil and fil ter. Air Filtering
CAUTION:
When vehicles are operating under arduous conditions, the following service item mus t be carried out
every 12 months or 15,000 miles (24,000 km).
Replace the ai r fi lt er el ement.
For addit ional informat ion, refer t o: Air Cl eaner (303-12A Int ake Ai r Dis t ri but ion and Fi lt ering - I6 3.2L Petrol ,
Removal and Inst all ati on). Accessory Drive Belt
CAUTION:
When vehicles are operating under arduous conditions, the following service item mus t be carried out
every 5 years or 75,000 miles (120,000 km).
Replace the access ory drive bel t. For addi ti onal informat ion, refer to: Acces s ory Drive Belt (303-05A Acces s ory Drive
- I6 3.2L Pet rol, Removal and Ins tal lat ion). Camshaft Timing Belt, Tensioner and Pulley
CAUTION:
When vehicles are operating under arduous conditions, the following service item mus t be carried out
every 4 years or 60,000 miles (96,000 km).
Replace the cams haft t iming belt , tens ioner and pul ley.
For addit ional informat ion, refer t o: Timi ng Belt (303-01B Engi ne - TD4 2.2L Dies el, Removal and Inst all ati on).
Radiator/Charge Air Cooler and Cooling Fan
CAUTION:
When vehicles are operating under arduous conditions, the following items must be ca rried out.
Vis uall y check t he radiat or/charge air cool er for ext ernal obst ruct ions, check cooli ng fan bl ades for damage.Remove any debris from t he charge air cool er us i ng a l ow pres s ure hos e.
Continuous Use In Severe Off-Road Conditions
CAUTION:
After 50 miles (80 km) continuous use in severe off-road conditions i.e. w ading, dee p mud and
abrasive grit/slurry, the following items must be cleaned and inspected.

Four i nit iators are fi tt ed t o the vehicl e. The front i ni ti ators are l ocat ed near t he front of the front wheel arches , behind t hefender s pl ash shi elds . The rear init iat ors are located at t he rear of t he rear wheel arches , behind t he fender spl ash shi el ds.Each init iat or has a connect or which connects to the vehicle body harnes s .
The ini ti at or is a pass ive, LF t rans mit ter. The init iat ors t rans mi t their s ignals which are recei ved by the ti re press ures ens ors , prompt ing them to modi fy their mode st atus .
The TPMS energis es each init iat or in t urn usi ng LF dri vers. The corres ponding t ire pres s ure sens or det ect s t he LF s ignal andres ponds by modifyi ng the mode s tat us wit hin t he RF t rans mis s ion.
Tire Pressure Sensor
The TPMS us es act ive t ire pres s ure s ens ors whi ch are l ocat ed on each wheel , ins ide the ti re cavit y. The sens or incorporat est he ti re val ve and is s ecured in the wheel by a nut on t he outs i de of the wheel. The s ensor contains a Pri nt ed Ci rcuit Board(PCB) whi ch hous es a Pos it ive Temperat ure Co-efficient (PTC) s ens or, a Piezo pres s ure s ens or. a radi o receiver andt ransmit ter and a l it hium bat t ery.
The t ire pres sure s ensors use the PTC sens or and the Pi ezo sens or to periodically measure t he pres sure and t emperatureof the ai r ins ide t he t ire. The dat a is trans mi tt ed by RF dat a s ignals at ei ther 315 MHz or 433 MHz dependant on marketrequirements .
The RF t rans mis s ion from t he sens or cont ai ns a unique i dent ificati on code in i ts trans mi ss i on dat a. This all ows t he TPMSt o identi fy the wheel on t he vehi cl e. If t he s ens or is replaced on a 'running' wheel, t he new s ens or i dent ificati on wil l belearnt when the vehicle is driven at s peed of more t han 20 km/h (12.5 mph) for 15 minutes .
If a new s ensor i s fi tt ed t o t he spare wheel, t he identi fi cat ion for that s ens or can be programmed int o t he TPMS usi ng IDS.The code is provi ded on a l abel wit h t he complet e ti re, wheel and sens or ass embly when new and is al s o pri nted on t hecas i ng of each s ensor. Alt ernati vel y, t he s pare wheel may al so be programmed to the TPMS by us i ng it as a 'running' wheelfor 15 minutes at a speed of more t han 20 km/h (12.5 mph), t hen replacing it t o t he spare wheel l ocat ion.
The t ire pres sure s ensor can als o det ect when t he wheel i s rot ati ng. In order t o preserve bat t ery power, t he s ens or us esdifferent t rans mis s ion rates when the wheel is st ati onary or moving. The wheel s peed required to change from st ati onaryt o moving t rans mis s ion rates is very low t o al low for the requi rement for sl ow off-road dri ving.

DT CDescriptionPossible CauseAction
C1A5893Front Ri ght W heel Module - nooperat ion (los t s ens or)Siemens i nternal algori thmIns tal l a new module as required
C1A5911Ri ght Front Init iat or - short togroundRight front ini ti at or ci rcuit -s hort t o groundRefer to el ect ri cal circui t diagrams andcheck ri ght front i ni ti ator circui t for s hort t oground
C1A5912Ri ght Front Init iat or - short topowerRight front ini ti at or ci rcuit -s hort t o powerRefer to el ect ri cal circui t diagrams andcheck ri ght front i ni ti ator circui t for s hort t opower
C1A5913Ri ght Front Init iat or - open ci rcuitRight front ini ti at or ci rcuit -open circuitRefer to el ect ri cal circui t diagrams andcheck ri ght front i ni ti ator circui t for openci rcuitC1A6016Rear Left W heel Module - circui tvolt age below t hres hold (lowbat tery)
Siemens i nternal algori thmIns tal l a new module as required
C1A6086Rear Left W heel Module - s i gnali nval id (out of range)Siemens i nternal algori thmIns tal l a new module as required
C1A6093Rear Left W heel Module - nooperat ion (los t s ens or)Siemens i nternal algori thmIns tal l a new module as required
C1A6111Left Rear Init iator - s hort t ogroundLeft rear i nit iator circui t -s hort t o groundRefer to el ect ri cal circui t diagrams andcheck left rear init iat or ci rcuit for short toground
C1A6112Left Rear Init iator - s hort t o powerLeft rear i nit iator circui t -s hort t o powerRefer to el ect ri cal circui t diagrams andcheck left rear init iat or ci rcuit for short topower
C1A6113Left Rear Init iator - open circui tLeft rear i nit iator circui t -open circuitRefer to el ect ri cal circui t diagrams andcheck left rear init iat or ci rcuit for openci rcuitC1A6216Rear Right W heel Modul e - circui tvolt age below t hres hold (lowbat tery)
Siemens i nternal algori thmIns tal l a new module as required
C1A6286Rear Right W heel Modul e - s ignali nval id (out of range)Siemens i nternal algori thmIns tal l a new module as required
C1A6293Rear Right W heel Modul e - nooperat ion (los t s ens or)Siemens i nternal algori thmIns tal l a new module as required
C1A6311Ri ght Rear Ini ti ator - s hort t ogroundRight rear i nit iator circui t -s hort t o groundRefer to el ect ri cal circui t diagrams andcheck ri ght rear init iat or ci rcuit for s hort t oground
C1A6312Ri ght Rear Ini ti ator - s hort t obat teryRight rear i nit iator circui t -s hort t o powerRefer to el ect ri cal circui t diagrams andcheck ri ght rear init iat or ci rcuit for s hort t opower
C1A6313Ri ght Rear Ini ti ator - open circui tRight rear i nit iator circui t -open circuitRefer to el ect ri cal circui t diagrams andcheck ri ght rear init iat or ci rcuit for openci rcuitC1B1412Sens or s upply #1 - circuit s hort t opowerSensor s uppl y #1 ci rcuit -s hort t o powerRefer to el ect ri cal circui t diagrams andcheck s ens or s upply #1 circui t for s hort t opower
C1D1800Local is ati on fai ledTire pres s ure moni torlocali sat ion fail edCheck for addit ional relat ed DTCs and referto t his DTC Index
C1D2105W heel module - general s i gnalfail ureSiemens i nternal algori thmCarry out t he pinpoint t est s as sociat ed t othis DTC usi ng t he manufacturer approveddi agnos ti c s yst em
U015500Los t Communicati on W i thIns trument Panel Clus ter (IPC)Cont rol Modul e
Lost communi cat ion wi thins t rument clus terCarry out t he as sociat ed network tes t forthis DTC usi ng t he manufacturer approveddi agnos ti c s yst em
U016400Los t Communicati on W i th HVACCont rol Modul eLost communi cat ion wi thcli mate control modul eCarry out t he as sociat ed network tes t forthis DTC usi ng t he manufacturer approveddi agnos ti c s yst em

Publi s hed: 11-May-2011
Wheels and Tires - Tire Low Pressure Sensor
Removal and Inst all ati on
Removal
W ARNING: The val ve seal and s teel was her mus t be replaced each t ime a t ire is changed to avoi d s eal failure. Thes eal and was her must be replaced if t he s ensor i s removed. Removal of the sens or retai ning nut mus t be regarded ass ens or removal. The valve cap mus t always be in pl ace except when i nfl at ing, rel easing or checki ng pres s ure.
• NOTE: If the s ens or i s repl aced on a 'runni ng' wheel, t he new s ens or ident ifi cat ion will be learnt when t he vehi cl e i s fi rs tdri ven. If a new s ensor i s ins t al led t o t he s pare wheel, t he ident ifi cat ion for that s ensor mus t be programmed i nto t he t irepres s ure moni toring s yst em (TPMS) module us ing Land Rover approved di agnos ti c equi pment . The ident ifi cat ion code i sprovided on a label wit h t he compl ete as s embly and i s als o print ed on t he cas ing of each s ens or.
1. W ARNING: Make sure t o s upport the vehicle wit h axles tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he wheel and t ire.
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal andInst all at ion).
2.
3. CAUTION: To avoid damage t o t he t ire low pres sure s ens or,rel ease the t ire bead from the rim, 180 degrees from t he val ve.
Remove t he ti re from t he wheel.
3.
Remove and dis card t he nut.Releas e and wi thdraw the s ens or al ong thevalve axis .
4.
Remove and dis card t he s eal and was her.5.
Installation
1. CAUTIONS:1.

Publi s hed: 11-May-2011
Vehicle Dynamic Suspension - Rear Suspension Height Sensor
Removal and Inst all ati on
Removal
• NOTE: This s ens or i s only fit ted to vehicles wit h Xenon headlamps and is i nst all ed on the LH s ide of t he vehi cl e.
• NOTE: Removal s t eps in t his procedure may cont ain i nst all ati on det ail s.
1. W ARNING: Make sure t o s upport the vehicle wit h axle
s tands .
Rais e and s upport t he vehi cl e.
1.
Remove t he wheel and t ire.
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal and
Inst all at ion).
2. T orque:
10 Nm 3.
4.

Publi s hed: 11-May-2011
Anti-Lock Control -
General SpecificationItemSpecification
Syst em make / typeConti nent al Teves - MK23E1
Wheel speed sensors:MakeConti nent al Teves
Yaw rate sensor:
Make / t ypeConti nent al Teves - RSC03Locat ionCenter cons ole in front of gear shi ft
Torque SpecificationsDescriptionNmlb-ft
ABS module to mount ing bracket nuts107
Accel erometer bolt s65Brake flui d t ube uni ons1511
Front road wheel s peed sens or to wheel knuckle bol t54
Rear road wheel speed s ensor t o wheel knuckle bolt54

Publi s hed: 11-May-2011
Anti-Lock Control - Front Wheel Speed Sensor
Removal and Inst all ati on
Removal
Rais e and s upport t he vehi cl e.
1.
Remove t he front wheel and t ire.
Refer t o: W heel and Ti re (204-04 W heel s and Tires, Removal and
Inst all at ion).
2.
Releas e t he fender spl as h shi el d.
Refer t o: Fender Spl ash Shi eld (501-02 Front End Body Panel s ,
Removal and Ins tall ati on).
3. 4.
T orque:
5 Nm 5.
Installation To i nst all , revers e t he removal procedure.
1.
If a new component i s t o be ins t al led, configure usi ng IDS.
2.