diagram MAZDA 6 2002 Suplement Service Manual

T–4
MULTIPLEX COMMUNICATION SYSTEM
SYSTEM WIRING DIAGRAMA6E811155430203
.
End Of SieCAN SIGNAL-CHARTA6E811155430204
OUT: Output (sends signal)
IN: Input (receives signal)
1
2
67
3
8
4
5
ROAF AG
HG
2M2J2W
2X
9
10
CAN_L
CAN_H
A6E81111102
1PCM
2 DSC HU/CM (with DSC)
3 ABS (ABS/TCS) HU/CM (with ABS (ABS/TCS))
4 Data link connector-2
5 Instrument cluster
6 TCM (JA5AX-EL)7 4WD control module (4WD)
8Twist pair
9 2R (except MZR-CD (RF Turbo))
39 (MZR-CD (RF Turbo))
10 2U (except MZR-CD (RF Turbo))
13 (MZR-CD (RF Turbo))
SignalMultiplex module
PCM TCMABS (ABS/TCS)
HU/CM or
DSC HU/CM4WD control
moduleInstrument
cluster
Accelerator pedal position
(MZR-CD (RF Turbo))OUT IN IN–IN
Air induction type OUT–IN––
ATF temperature IN OUT–––
AT warning light conditions
(JA5AX-EL)IN OUT––IN
Battery reconnection
(except MZR-CD (RF
Turbo))OUT IN–––
Brake system configuration
(EBD/ABS/TCS/DSC)IN–OUT–IN
Brake system
statusABS IN–OUT––
EBD/ABS/
TCS/DSC––OUT IN IN
Brake system warning light
conditions (brake fluid level
sensor)––IN–OUT
Country OUT–IN––
Coupling torque (with
DSC)––IN OUT–
Coupling torque request
(with DSC)––OUT IN–

T–6
MULTIPLEX COMMUNICATION SYSTEM
ON-BOARD DIAGNOSTIC FUNCTIONA6E811155430205Outline
•The on-board diagnostic function is incorporated into the PCM, TCM, ABS (ABS/TCS) HU/CM (with ABS (ABS/
TCS)), DSC HU/CM (with DSC), 4WD control module, and instrument cluster. This function can narrow down
CAN system malfunction locations.
•Due to the adoption of the TCM and the 4WD CM, some DTCs and PID/data monitor items have been added.
Other functions are the same as those of the current Mazda6 (GG) model.
Block Diagram
.
Fail-Safe Function
•When the failure detection function detemines that there is a malfunction, the fail-safe function illuminates a
warning light to advise the driver of the malfunction.
1
3
24
5
6
A6E81111103
1PCM
2 TCM (JA5AX-EL)
3 ABS (ABS/TCS) HU/CM or DSC HU/CM4 4WD control module (4WD)
5 Instrument cluster
6Twist pair
Module Fail-safe function
PCM•MIL illuminated
TCM•AT warning light illuminated
•ABS (ABS/TCS) HU/CM (with ABS (ABS/TCS))
•DSC HU/CM (with DSC)•ABS (ABS/TCS) suspended (with ABS (ABS/TCS))
•DSC suspended (with DSC)
•ABS warning light illuminated
•DSC/TCS indicator light illuminated
•DSC OFF light illuminated
•TCS OFF light illuminated
4WD control module•4WD indicator light illuminated
Instrument cluster•Speedometer, tachometer, water temperature gauge: 0 displayed

WARNING AND INDEICATOR SYSTEM, THEFT-DETERRENT SYSTEM
T–11
T
SYSTEM WIRING DIAGRAMA6E811801069203
.
End Of Sie
OUTLINEA6E812050000201•An intruder sensor has been adopted on the rear part of the roof. (WGN)
•The construction and operation of the theft-deterrent system is the same as that of the current Mazda6 (GG)
model.
End Of Sie
INTRUDER SENSORA6E812050000202Outline
•WGN models are equipped with intruder sensors in two places in the vehicle, due to the necessity of movement
detection in the all around wider vehicle interior. The intruder sensors are located in the roof at the front (with
sliding sunroof), or the center (without sliding sunroof), and the cargo space.
•The structure and operation of the rear intruder sensor is the same as that of the current front and center
intruder sensors.
IG1
B+
1
345
2
6
97
8
2H 2V
1C 2F 2D 2M 2X 2W
A6E81181004
1 Instrument cluster
2Microcomputer
3 Glow indicator light
4 Sedimentor warning light
5 4WD indicator light6 PCM, ABS (ABS/TCS) HU/CM or DSC HU/CM
7 Fuel gauge sender sub-unit (4WD)
8 Fuel gauge sender unit
9 Sedimentor switch
THEFT-DETERRENT SYSTEM

T–12
THEFT-DETERRENT SYSTEM
Structural View
.
System Wiring Diagram
.
End Of Sie
3
1
2
A6E81201103
1 Front intruder sensor (with sliding sunroof)
2 Center intruder sensor (without sliding sunroof)3 Rear intruder sensor (WGN)
B+ IG1
F
PA
B
C
1
2
CB
A
B O
C
3
L
A6E81201101
1 Theft-deterrent control module
2 Rear intruder sensor (WGN)3 Front intruder sensor (with sliding sunroof)
Center intruder sensor (without sliding sunroof)

T–42
ON-BOARD DIAGNOSTIC [MULTIPLEX COMMUNICATION SYSTEM]
PROCEDURES FOR DETERMINING THE LOCATION OF A MALFUNCTIONA6E816255430204System Wiring Diagram
PCM
1. Check the display of DTC U0101, U0121 and/or U0155, using the SST (WDS or equivalent). (See T–41 DTC
TABLE.)
2. Referring to the following table, determine the malfunctioning part of the CAN system.
2WD
X: Normal
—: Communication error
PCMWIRING
HARNESS A
TWIST PAIRWIRING
HARNESS BWIRING
HARNESS C
INSTRUMENT
CLUSTER ABS (ABS/TCS)
HU/CM
OR
DSC HU/CM
TCM4WD
CONTROL
MODULE
WIRING
HARNESS EWIRING
HARNESS G
WIRING
HARNESS D
WIRING
HARNESS F
PCMWIRING
HARNESS A
INSTRUMENT
CLUSTER ABS (ABS/TCS)
HU/CM
OR
DSC HU/CM
WIRING
HARNESS C
WIRING
HARNESS B
2WD
4WD
A6E81621102
ModuleCommunication status
Malfunction location
ABS (ABS/TCS) HU/CM
DSC HU/CMInstrument cluster
PCM——•Wiring harness A
•PCM
—X•Wiring harness B
•ABS (ABS/TCS) HU/CM
•DSC HU/CM
X—•Wiring harness C
•Instrument cluster