wheel MAZDA 626 1987 User Guide

1 A DISASSEMBLY (CYLINDER BLOCK)
CYLINDER BLOCK—I
1. Clutch cover (MTX), Backing plate (ATX)
2. Clutch disc (MTX), Drive plate (ATX)
3. Flywheel (MTX), Adaptor (ATX)
4. End plate
5. Oil pan
76G01A-051
6. Oil strainer
7. Stiffener (FE 8-valve...only ECE, 12-valve)
8. Rear cover
9. Water pump assembly
10. Oil pump assembly
1A—44

DISASSEMBLY (CYLINDER BLOCK) 1 A
76G01A-125
Disassembly Note
Clutch cover, flywheel (MTX) or drive plate (ATX)
Remove the clutch cover and flywheel (MTX), or drive
plate (ATX) with the SST.
Oil pan
1. Remove the oil pan mounting bolts.
2. Insert a scraper or a suitable tool between the oil
pan and the stiffener or the cylinder block to sep-
arate them.
3. Remove the oil pan.
Caution
Do not bend the oil pan when prying loose.
76G01A-052
1A—45

DISASSEMBLY
(CYLINDER BLOCK) 1 A
86U01X-137
76G01A-138
86U01X-139
Oil Pan
1. Apply a continuous bead of silicon sealant to the
oil pan along the inside of the bolt holes, and over-
lap the ends.
2. Install the oil pan.
Tightening torque:
7—12 Nm (70—120 cm-kg, 61—104 in-lb)
Flywheel (MTX), Drive Plate (ATX)
1. Remove any old sealant from the bolts and bolt
holes. If old sealant can not be removed from the
bolt,-replace it.
2. Apply sealant to the bolt threads.
(MTX)
3. Install, and tighten the flywheel with the SST.
Tightening torque:
96—103 Nm (9.8—10.5 m-kg, 71—76 ft-lb)
(ATX)
3. Install, and tighten the drive plate adaptor, drive
plate, and backing plate with the SST.
Tightening torque:
96—103 Nm (9.8—10.5 m-kg, 71—76 ft-lb)
76G01A-139
1A—71

1A INSTALLATION
Driveshaft
1. Apply grease to the end of the driveshaft.
2. Install the driveshaft and a new clip.
Caution
a) When installing the driveshaft, be careful
not to damage the oil seal.
b) After installation, pull the front hub outward
to confirm that the driveshaft is securely
held by the clip.
86U01X-184
Lower Arm
Install the lower arm ball-joint to the knuckle; then tight-
en the lock nut.
Tightening torque:
43—54 N-m (4.4—5.5 m-kg, 32—40 ft-lb)
86U01X-185
Tie-Rod End
1. Install the tie-rod end to the knuckle.
Tightening torque:
29—44 N-m (3.0—4.5 m-kg, 22—33 ft-lb)
2. Install the cotter pin.
86U01X-186
Stabilizer Control Rod
Install and adjust the front stabilizer control rods.
Dimension A: 20.1 mm (0.79 in)
Tightening torque: 16—23 N-m (1.6—2.3 m-kg, 12—17 ft-lb)
Install the front wheel.
Tightening torque:
88—118
N
m (9.0—12.0 m-kg, 65—87 ft-lb)
1A—94

REMOVAL 1B
1. Battery and battery carrier
2. Air cleaner assembly
3. High-tension lead
4. Accelerator cable
5. Fuel hose
6. Radiator hose
7. Radiator harness
8. Radiator and electric fan
9. EGI harness
10. Engine harness
11. Brake vacuum hose
12. Canister hose (Unleaded
fuel)
13. Heater hose
14. Transaxle harness
15. Speedometer cable
16. Clutch release cylinder
17. Drive belt
18. A/C compressor and
bracket
19. P/S oil pump
20. Engine side cover
21. Front wheel
22. Tie-rod end
23. Stabilizer control rod
24. Lower arm bushing
25. Driveshaft
26. Change rod
27. Extension bar
28. Exhaust pipe
29. Engine mount
30. Engine and transaxle
31. Transaxle
76G01B-037
Removal Note
Fuel hose
Warning
a) Cover the hose with a rag because fuel will
spray out when disconnecting.
b) Keep sparks and open flame away from the
fuel area.
Plug the disconnected hoses to avoid fuel leakage.
76G01A-11£
P/S pump, A/C compressor
Remove the P/S pump and A/C compressor with the
hoses still connected to them, secure the pump and
compressor as shown in the figure.
67U01X-029
Driveshaft
Remove the driveshafts. (Refer to Section 9.) Slide
the SST into the transaxle.
86U01X-060
1B—23

DISASSEMBLY (TIMING BELT) 1 B
Mark the
direction of
rotation
76G01A-121
76G01B-119
Disassembly Note
Crankshaft pulley
1. Set the SST against the flywheel.
2. Remove the crankshaft pulley.
Timing belt
1. Loosen the tensioner lock bolt, and remove the ten-
sioner spring.
2. Mark the timing belt rotation for proper reinstalla-
tion if it is reused.
3. Remove the timing belt.
Caution
Be careful not to allow oil or grease on the
belt.
Camshaft pulley
Remove the pulley lock bolt using a screw driver to
prevent the camshaft from turning.
76G01A-123
1B—27

1 B DISASSEMBLY (CYLINDER BLOCK)
CYLINDER BLOCK-I
76G01B-043
1. Clutch cover 6. Oil strainer
2. Clutch disc 7. Rear cover
3. Flywheel 8. Water pump assembly
4. End plate 9. Oil pump assembly
5. Oil pan 10. Oil jet
1B—30

DISASSEMBLY (CYLINDER BLOCK) 1 B
76G01B-044
Bolt hole
Oil pan • ,„
Cylinder block
76G01B-045
Disassembly Note
Clutch cover and flywheel
Remove the clutch cover and flywheel with the SST.
Oil pan
1. Remove the oil pan mounting bolts.
2. Install the bolt ©from the mounting bolt or 10 mm
(0.39 in) bolts in the specified bolt holes ©(both
sides).
3. Screw in the bolts gradually and alternately to re-
move the oil pan.
Caution
a) Do not pry the oil pan to prevent damaging
the contact surface.
b) Do not damage or scratch the contact sur-
face when removing the oil sealant.
4. Remove the oil pan.
1B—31

ASSEMBLY (CYLINDER BLOCK) 1 B
Oil Pan
1. Apply a continuous bead of silicon sealant to the
oil pan around inside of the bolt holes and over-
lap the ends.
2. Install the oil pan.
Tightening torque:
7—12 Nm (70—120 cm-kg, 61—104 in-lb)
Caution
Oil pan projection and recession from the end
of the cylinder block must not be more than
1.5 mm (0.06 in).
76G01 B-080
Flywheel
1. Remove any old sealant from the bolts and bolt
holes. If old sealant can not be removed from the
bolt, replace it.
2. Apply sealant to the bolt threads.
76G01B-081
3. Install, and tighten the flywheel with the SST.
Tightening torque:
96—103
N
m (9.8—10.5 m-kg, 71—76 ft-lb)
76G01B-082
Clutch Disc and Clutch Cover
Install the clutch disc and clutch cover using the SST.
(Refer to Section 6.)
Tightening torque:
22—32
N m
(2.2—3.3 m-kg, 16—24 ft-lb)
76G01 B-083
1B—57

1B INSTALLATION
86U01X-184
86U01X-185
86U01X-186
Driveshaft
1. Apply grease to the end of the driveshaft.
2. Install the driveshaft and a new clip.
Caution
a) When installing the driveshaft, be careful
not to damage the oil seal.
b) After installation, pull the front hub outward
to confirm that the driveshaft is securely
held by the clip.
Lower Arm
Install the lower arm ball-joint to the knuckle; then tight-
en the lock nut.
Tightening torque:
43—54 Nm (4.4—5.5 m-kg, 32—40 ft-lb)
Tie-Rod End
1. Install the tie-rod end to the knuckle.
Tightening torque:
29—44 Nm (3.0—4.5 m-kg, 22—33 ft-lb)
2. Install the cotter pin.
Stabilizer Control Rod
Install and adjust the front stabilizer control rods.
Dimension A: 20.1 mm (0.79 in)
Tightening torque: 16—23 Nm (1.6—2.3 m-kg, 12—17 ft-lb)
Install the front wheel.
Tightening torque:
88—118 Nm (9.0—12.0 m-kg, 65—87 ft-lb)

86U01X-180

1B—76