power steering fluid MAZDA MX-5 1994 User Guide

N ENGINE SPEED SENSING POWER STEERING Caution Never hold the steering wheel to the extreme left or right for more than five seconds with the engine running. This could damage the power steering d pump- 8. Turn the steering wheel fully to the left and right and measure the fluid pressure generated by the gear hous- ing. If the pressure is not within specification, replace the gear housing assembly. Gear housing fluid pressure: 7,601--8,335 kPa (77.545.0 kgflcm2, 1,103-1,208 psi) 9. Remove the gauge set. Install and tighten the pressure hose to the specified torque. Tightening torque: 3247 N.m (3.24.8 kgf.m, 24--34 ft.lbf} 10. Bleed the air from the system. (Refer to page N-21.) STEERING WHEEL AND COLUMN Obtain the code number and deactivate the audio anti- theft system before disconnecting the battery. (Refer to section T.) On-vehicle Inspection -1 Steering wheel effort 1. With the vehicle on a hard, level surface, put the wheels in the straight-ahead position. 2. Start the engine and warm the power steering fluid to 50--60°C (1 22-1 40°F). 3. With the engine running at idle, attach a pull scale to the outermost point of the steering wheel spoke. Then, starting with the wheels in the straight-ahead posi- tion, measure the effort required to turn the steering wheel to the left and to the right. Steering wheel effort: 2635 N (2.63.6 kgf, 5.3-7.9 Ibf) (during one turn of the steering wheel) 2 4. If not within specification, check the following: fluid level, air in system, fluid leakage at hose or connections, func- tion of oil pump and steering gear, and tire pressure. Gartner Banana

ENGINE SPEED SENSING POWER STEERING N STEERING GEAR AND LINKAGE Removal / Installation 1. Turn the wheels to the straight-ahead position. 2. Loosen the wheel lug nuts. 3. On level ground, jack up the front of the vehicle and support it on safety stands. 4. Remove the wheels. Note Turning the steering wheel while the steering gear is removed will make reinstallation difficult. Do not turn the steering wheel while the steering gear is removed. If the steering wheel is turned in that condi- tion, the clockspring connector may have to be adjusted. (Refer to section T.) 5. Remove in the order shown in the figure, referring to Removal Note. 6. With the wheels in the straight-ahead position, install in the reverse order of removal. 7. Tighten all necessary bolts and nuts to the specified torque. 8. After installation: (1) Check for fluid leakage. (Refer to page N-22.) (2) Bleed air from the system. (Refer to page N-21.) (3) Adjust the front wheel alignment. (Refer to section R.) 1. Cotter pin 5. Pressure pipe 2. Nut ~emovai Note ............... page N-26 3. Tie-rod endlsteering knuckle 6. Return hose Removal Note ............... page N- 7 7. Mounting bracket bolt 4. Bolt 8. Steering gear and linkage Gartner Banana

ENGINE SPEED SENSING POWER STEERING N POWER STEERING OIL PUMP Removal / Installation 1. Remove in the order shown in the figure, referring to Removal Note. u 2. Install in the reverse order of removal. 3. After installation: (1) Check connections for fluid leakage. (Refer to page N-22.) (2) Bleed air from the system. (Refer to page N-21.) 1. Drive belt 3. Press~~re pipe ................... ............... w Inspection page N-37 Removal Note page N-34 Adjustment .................. page N-38 4. Return hose Replacement ................ page N-38 5. Power steering oil pump 2. Power steering pressure switch connector Gartner Banana

FRONT SUSPENSION (DOUBLE-WISHBONE) CROSSMEMBER Removal I Inspection 1 lnstallation Note 4 Use a container or rags to collect the power steering fluid when disconnecting the power steering pipes. 1. Jack up the vehicle. 2. Remove the wheels and the undercover. 3. Support the engine with a hoist. 4. Lower the crossmember and other suspension parts as an assembly, and then separate the parts. 5. Remove in the order shown in the figure. 6. lnspect all parts and repair or replace as necessary. 7. Loosely tighten the stabilizer bracket, upper arm, and lower arm bolts. Tighten all other nuts and bolts to the specified torques. 8. Lower the vehicle. 9. With the vehicle unloaded, tighten the stabilizer bracket, upper arm, and lower arm bolts to the specified torques. 10. Adjust the front wheel alignment. (Refer to page R-6.) 11. Bleed the air from the brake system. (Refer to section P.) 12. Bleed the air from the Power Steering System. (Refer to section N.) Q - re-no ~L1.3--11.W, Okl-m} 94-1;2 (9.Cll.5,69--83) 1 &26 {1.&2.7,14--19) 1 S21 (1 3-- 1. Brake pipe Removal / lnstallation . . . . . . . . . Section P 2. Pinion shaft bolt Removal / lnstallation . . . . . . . . Section N 3. Power steering pipe Removal 1 lnstallation . . . . . . . . Section N 4. Shock absorber bolt 5. Stabilizer bracket bolt 6. Upper arm bolt 7. Performance rod 8. Adjusting cam bolt 9. Steering gear bracket bolt 10. Front crossmember assembly lnspect for damage Gartner Banana

TECHNICAL DATA --- M. FRONT AND REAR AXLES Specifications TY pe Bearing Angular ball bearing 0.05 10.002) Front axle Rear axle - Wheel bearing play mm {in) I Maximum Bearina Anaular ball bearina . .. Wheel bearina plav mm {in) I Maximum " " 0.05 {0.002) 'TORSEN" LSD I Standard TY pe Reduction aear Hvpoid sear Reduction ratio Differential aear 4.100 Worm near ("1ORSEN"LSD) I Straiaht-bevel gear - - Ring gear size mm {in) 1 Grade 182.88 17.201 API service GL-5 Oil 1 Viscosity Above -18°C {O°F): SAE 90 Below -18°C {O°F): SAE 80W Differential Capacity L {US at. Imp at) Locknut tightening torque: 128-284 N.m {I 3-29 kgf.m, 94.1-209.7 ft.lbf) Drive pinion preload (without oil seal) TORSEN" is a Backlash mm {in) . , egistered trademark of ZEXEL-GLEASON US, Side gear and pinion gear Final gear , INC Length (Pilot section to pilot section) mm (in N. STEERING SYSTEM Steering wheel Outer diameter mm {in} 1 370 11 4.6) Type item Free play mm {in) I 630 {O-1.18) Wheel effort N (kaf, Ibfl 14.9--29.4{0.5--3.0, 1.1-4.6) 123.545.3 12.A4.6,5.3--8.0) turns I 3.36 1 2.8 I 1 Manual steering Steering Shaft Shaft type I Collapsible, non-tilt Power steering Joint type I 2-cross joint Power steering system Gear ratio 1 m (infinite) Rack stroke rnm {in) I 121 .O 14.76) Power assist type Engine speed sensing Power steering fluid Fluid capacity L {US qt, Imp qt} Fluid pressure kPa {kgf/cm2, psi) Gear type - - ATF DexrongII oi M-111 0.8 {0.85,0.70) 7,603--8,339 (77.5850, 1 ,I 02-1,209) Rack-and-pinion Gartner Banana