sensor MAZDA MX-5 1994 Owner's Manual

TROUBLESHOOTING GUIDE RELATIONSHIP CHART Fuel injector TEN Terminal (Data link connector) Ignition Switch (Start Position) Steering Pressure Sensor X X X X X X X X X X X X X X X xoo Blower Switch Headlight Switch Stoplight Switch Neutral and Clutch Switches (MT) Parklneutral switch (AT) Air Conditioning Sensor Idle Switch Throttle I BDL) Position Sensor I Sensor (NO) Barometric Absolute Pres- sure Sensor IGF Signal Heated Oxygen Sensor Engine Coolant Temperature Sensor Sensor Mass Air- flow Sensor Intake Air Temperature Sensor Crankshaft SGTSignal Position Sensor SGC-Signal Gartner Banana

TROUBLESHOOTING GUIDE INSPECTION Check if PCME terminal voltages are OK (IC, 1 R, IT, 2D, 20 and 2Q) page F-146 :heck for air leakage of intake air system malfunction page F-100 :heck for EGR system malfunction page F-124 Check if mass airflow sensor US page F-152 Check for correct engine compression Section B Engine compression: 1,255-883 kPa j12.8-9.0 kgf/cm2, 182-128 psil-300 rpm Check if spark plugs are OK WEAR AND CARB/ON BUILDUP BURNS PLUG GAP 1 .O-1 .l mm (0.040-4.043 in) DAMAGE AND DETERIORATION DAMAGE - Yes Yes - No Yes - No Yes - No Yes No - Yes - No - ACTION Go to next step Check for cause (Refer to "Check Point for Each Terminal") page F-148 Repair or replace Go to next step Repair or replace Go to next step Go to next step Repair or replace page F-99 Go to next step Check engine condition Section B Worn piston, piston rings or cylinder wall Defective cylinder head gasket Distorted cylinder head Improper valve seating a Valve sticking in guide Go to next step Repair, clean, or replace @a Section G Try known good PCME and check if condition im- 3rOVeS page F-144 Gartner Banana

TROUBLESHOOTING GUIDE ESCRIPTION I 0 Engine cranks at normal speed but requires excessive cranking time (more than 5 sec.) before starting Batterv in normal condition 5 I TROUBLESHOOTING HINTS] D Air/Fuel mixture too lean Q Air/Fuel mixture too rich Fuel injection control malfunction Air cleaner element clogged (Correction for coolant temperature) Mass airflow sensor stuck Low fuel line pressure 31 Poor ignition spark CRANKS NORMALLY BUT HARD TO START - ALWAYS Air leakage STEP - 1 INSPECTION Check if "00" is displayed on Self-Diagnosis Checker with ignition switch ON page F-79 Check for correct intake manifold vacuum at idle Vacuum: More than 450 mmHg (17.7 inHg} VA/CUUM GAUGE Check if air cleaner element is clean page F-76 Check for correct fuel line pressure at idle page F-110 Fuel line pressure: 265--314 kPa (2.7-4.2 kgf/cm2, 38--46 psi} (Vacuum hose to pressure regulator discon- nected) INSTALL CLAPS ' - Yes - No - Yes - No - Yes No - Yes - No - ACTION Go to next step Diagnostic Trouble Code No. displayed Check for cause (Refer to specified check sequence) page F-81 "88" flashes Check PCME terminal 1 E voltage page F-145 Specification: Battery positive voltage (Ignition switch ON) Q If OK, replace PCME page F-143 o If not OK, check wiring between PCME and Self-Diagno- sis Checker page F-7 Go to next step Check for air leakage of intake air system components page F-100 Go to next step Replace air cleaner element page F-99 Go to next step Low pressure Check fuel line pressure while pinching fuel return hose Q If fuel line pressure quickly increases, check pressure regulator page F-118 0 If fuel line pressure gradually increases, check for clog- ging between fuel pump and pressure regulator If not clogged, check fuel pump maximum pressure page F-115 Gartner Banana

TROUBLESHOOTING GUIDE 9 LOW IDLE SPEEDIROUGH IDLE - BEFORE WARM-UP IESCRIPTION I Engine speed low or engine vibrates excessively at idle during warm-up TROUBLESHOOTING HINTS] D Low intake air amount Mass airflow sensor stuck Air cleaner element clogged Idle s~eed control Q Low fuel injection amount Fuel injection control malfunction (Correction for coolant temperature) O Poor atomization of fuel Air valve [Correction for coolant temperature ] iTEP I Low RVP (summer) fuel used in cold weather INSPECTION ACTION - Yes Check if "00" is displayed on Self-Diagnosis Check- er with ignition switch ON page F-79 GOG next step Diagnostic Trouble Code No. displayed Check for cause (Refer to specified check sequence) trs page F-81 - - "88"flashes Check PCME terminal 1 E voltage page F-145 Specification: Battery positive voltage (Ignition switch ON) 0 If OK, replace PCME @ page F-143 e If not OK, check wiring between PCME and Self-Diagno- sis Checker page F-7 Check switches for correct operation with Self- Diagnosis Checker Monitor Lamp and ignition switch ON ~8 page F-95 SELECT SW A Yes Go to next step Check if PCME terminal voltaaes are OK No - Yes - No - Yes Lamp not ON/OFF with specified switch Check for cause (Refer to specified check sequence) page F-96 Lamp always ON Check wiring between PCME terminal 1 D and Self-Diag- nosis Checker page F-7 Go to next step " (2D, 20 and 2Q) page F-146 Check for cause (Refer to "Check Point for Each Termi- nal") page F-148 Go to next step Check for correct intake manifold vacuum at idle Vacuum: More than 450 mmHg {I?.? inHg) Check for air leakage of intake air system components @ page F-100 INSTALL CLAPS Gartner Banana

TROUBLESHOOTING GUIDE INSPECTION Check if "00" is displayed on Self-Diagnosis Check- er with ignition switch ON page F-79 14 - -- Check for correct idle speed page F-77 IDLE MOVES UP AND DOWN Idle speed: 850 2 50 rpm (MT) 800 + 50 rpm (AT) GND TEN I DESCRIPTION I Engine speeds up and down periodically at idle [TROUBLESHOOTING HINTS] O Fuel cut occurs at idle O Air leakage of intake air system Air valve not closing after warm-up and idle speed @ Poor ignition spark reaches to fuel cut speed 8 AirIFuel mixture too rich Q Fuel injection amount fluctuating Fuel evaporative system malfunction Bad contact point inside mass airflow sensor 8 Low engine compression 5'=€% CONNECT TERMINAL AIR ADJUSTING SCREW Check for correct ignition timing at idle * page F-76 Ignition timing: 10" 2 lo BTDC - Yes - No - Yes - No Yes ACTION Go to next step Diagnostic Trouble Code No. displayed Check for cause (Refer to specified check sequence) @r page F-81 "88" flashes Check PCME terminal 1 E voltage re page F-145 Specification: Battery positive voltage (Ignition switch ON) 3 If OK, replace PCME page 6143 3 If not OK, check wiring between PCME and Self-Diagno- sis Checker page F-7 So to next step 2heck if idle speed can be adjusted by turning air adjust ;crew 3 If OK, adjust idle speed 3 If not OK, check air valve page F-105 20 to next step idjust I@= page F-76 Gartner Banana

TROUBLESHOOTING GUIDE F 18 ENGINE STALLS DURING START-UP DESCRIPTKlN I Engine unexpectedly stops running while starting VROUBLESHOOTING HINTS] @ Misfire occurs when depressing accelerator Q Lack of engine torque for start-up AirIFuel mixture too rich or too lean AirIFuel mixture too rich or too lean Incorrect ignition timing Weak ignition INSPECTION Check if brakes are dragging Section P Check if "00 is displayed on Self-Diagnosis Check- er with ignition switch ON * page F-79 SELECT SW A Check switches for correct operation with Self- Diagnosis Checker Monitor Lamp and ignition switch ON @ page F-95 Disconnect heated oxygen sensor connector and :heck if condition improves SENSOR CONNECTOR -3 I I - Yes - No Yes Yes No - Yes Low intake air amount Low en~ine com~ression ACTION Repair us Section P Go to next step Go to next step -- Diagnostic Trouble Code No. displayed Check for cause (Refer to specified check sequence) page F-81 "88" flashes Check PCME terminal 1 E voltage us page F-145 Specification : Battery positive voltage (Ignition switch ON) If OK, replace PCME rc+r page F-143 6 If not OK, check wiring between PCME and Self-Diagno- sis Checker e page F-7 Go to next step Lamp not ONIOFF with specified switch Check for cause (Refer to specified check sequence) uw page F-96 Lamp always ON Check wiring between PCME terminal 1 D and Self-Diag- nosis Checker page F-7 Check heated oxygen sensor @s page F-156 Go to next step Gartner Banana

TROUBLESHOOTING GUIDE 3ESCRIPTION ( Engine unexpectedly stops running while decelerating or after deceleration JROUBLESHOOTING HINTS] Ingine speed drops too much when releasing accelerator D Idle speed control malfunction Q Engine feedback control malfunction D Fuel cut control malfunction @ Idle speed misadjustment 19 INSPECTION :heck if "00" is displayed on Self-Diagnosis Check- 3r with ignition switch ON page F-79 ENGINE STALLS ON DECELERATION >heck switches for correct operation with Self- Diagnosis Checker Monitor Lamp and ignition switch ON page F-95 SELECT SW A MONITOR kt \A SYSTEM SELECT 1 Disconnect heated oxygen sensor connector and :heck if condition improves >heck if PCME terminal voltages are OK [2D, 20,2U, 2V 2Q, 2Y and 22) its page F-146 - Yes - No Yes Yes No - Yes ACTION Go to next step Diagnostic Trouble Code No. displayed Check for cause (Refer to specified check sequence) page Fa1 "88" flashes Check PCME terminal 1 E voltage us? page F-145 Specification: Battery positive voltage (Ignition switch ON) 6 If OK, replace PCME page F-143 o If not OK, check wiring between PCME and Self-Diagno. sis Checker page F-7 Go to'next step Lamp not ONJOFF with specified switch Check for cause (Refer to specified check sequence) page F-96 Lamp always ON Check wiring between PCME terminal 1 D and Self-Diag- nosis Checker page F-7 Check heated oxygen sensor @Tage F-156 Go to next step Go to next step Check for cause (Refer to "Check Point for Each Termi- nal") E%= page F-148 Gartner Banana

TROUBLESHOOTING GUIDE DESCRIPTION I Engine intermittently stops running Before stallina, ennine condition OK 21 [TRO~ESHOOTING HINTS] O Intermittently no spark or no fuel injection Poor connection in wiring harness ENGINE STALLS SUDDENLY (INTERMITTENT) INSPECTION Check if "00" is displayed on Self-Diagnosis Check- er with ignition switch ON page F-79 Tap, move, and wiggle harness and connectors to check if PCME terminal voltages are OK (1 B, 2A, 2B and 2C) @ page F-146 ACTION Go to next step Diagnostic Trouble Code No. displayed Check for cause (Refer to specified check sequence) @S page F-81 When checking wiring harness and connectors, tap, move, and wiggle suspect sensor and/or harness to recre- ate problem "88" flashes Check PCME terminal 1 E voltage @S page F-145 Specification: Battery positive voltage (Ignition switch ON) 0 If OK, replace PCME page F-143 0 If not OK, check wiring between PCME and Self-Diagno- sis Checker IS= page F-7 Go to Troubleshooting No.2 "CRANKS NORMALLY BUT WILL NOT START (NO COM- BUSTION)" page F-17 Check for cause (Refer to "Check Point for Each Termi- nal") page F-148 Gartner Banana

TROUBLESHOOTING GUIDE F b AirIFuel mixture leaning when depressing accelerator Fuel injection control malfunction (Correction for accelerating condition) Air leakage of intake air system Fuel line Pressure low 22 park adbance control malfunction HESITATESISTUMBLES ON ACCELERATION 0 - STEF DESCRIPTION] Flat spot occurs just after accelerator depressed or mild jerking occurs during acceleration rrROUBLESHOOTlNG HINTS] ACTION INSPECTION Check if "00" is displayed on Self-Diagnosis Check- er with ignition switch ON page F-79 SELECT SWA SYSTEM SELECT 1 - Yes Go to next step No - Yes - No Diagnostic Trouble Code No. displayed Check for cause (Refer to specified check sequence) uz page F-81 "88'1 flashes Check PCME terminal 1 E voltage page F-145 Specification: Battery positive voltage (Ignition switch ON) 6 If OK, replace PCME page F-143 Q If not OK, check wiring between PCME and Self-Diagno- sis Checker US page F-7 Check switches for correct operation with Self- Diagnosis Checker Monitor Lamp and ignition switch ON Go to next step page F-95 SELECT SW A Lamp not ON/OFF with specified switch Check for cause (Refer to specified check sequence) page F-96 Lamp always ON Check wiring between PCME terminal 1 D and Self-Diag- nosis Checker page F-7 Disconnect heated oxygen sensor connector and :heck if condition improves Yes - No - Yes -- -- Check heated oxygen sensor @s page F-156 Go to next step - :heck if PCME terminal voltages are OK :2M, 20, and 2Q) page F-146 Go to next step Check for cause (Refer to "Check Point for Each Termi- nal") page F-148 Gartner Banana

TROUBLESHOOTING GUIDE PROUBLESHOOTING HINTS] 3 Air/Fuel mixture too lean or too rich Fuel injection control malfunction Air leakage of intake air system 23 Fuel line pressure low Fuel evaporative malfunction 0 Spark advance control malfunction -- SURGES WHILE CRUISING - STEP DESCRIPTION ( Unexpected change in engine speed which is usually repetitive INSPECTION ACTION - Yes - No - Yes - No Check if "00" is displayed on Self-Diagnosis check- er with ignition switch ON page F-79 Go to next step SELECTSW A SYSTEM SELECT 1 Diagnostic Trouble Code No. displayed Check for cause (Refer to specified check sequence) page ~-81 -- - "88" flashes Check PCME terminal 1 E voltage @i= page F-145 Specification: Battery positive voltage (Ignition switch ON) 0 If OK, replace PCME @ page F-143 o If not OK, check wiring between PCME and Self-Diagno- sis Checker US page F-7 Check switches for correct operation with Self- Diagnosis Checker Monitor Lamp and ignition Go to next step switch ON w page F-95 SELECT SW A Lamp not ONIOFF with specified switch Check for cause (Refer to specified check sequence) page F-96 Lamp always ON Check wiring between PCME terminal 1 D and Self-Diag- nosis Checker @ page F-7 Disconnect heated oxygen sensor connector and check if condition improves Yes No - Yes Check heated oxygen sensor page F-156 Go to next step :heck if PCME terminal voltages are OK (1 R, 1 T, 2M, 20, and 2Q) as page F-146 Go to next step Check for cause (Refer to "Check Point for Each Termi- nal") * page F-148 Gartner Banana