timing belt MAZDA PROTEGE 1992 Repair Manual

I32 ASSEMBLY
Qill’ ’ 23UOB2-050
03UOB2-10
2. Install the timing belt pulley.
3. install the pulley Woodruff key with the tapered side toward
the oil pump body.
4. Install the pulley lock bolt.
5. Tighten the pulley lock bolt.
Tightening torque:
157-167 N#rn (16-17 m-kg, 116-123 ft-lb)
Water Pump
1. Remove all foreign material from the water pump mount-
ing surface.
2. Install the water pump and a new gasket.
Tightening torque:
19-25 N.m (1.9-2.6 m-kg, 14-19 ft-lb)
82-78

B2 ASSEMBLY
TIMING BELT
Torque Specifications
7.6-11 N:m
(60-l 10 cm-kg,
69-95 in-lb) \
-kg, 69-95 in-lb)
37-52
(3.8-5.3, 27-38)
157-167 (16-17, 116-123)
?.a--11 N-m
(60-110 cm-kg, 69-95 in-lb) /
12-17 (1.25-1.76, 9-13)
N-m (m-kg, ft-it
03UOB2.1
Idler
1. Install the idler.
Tightening torque:
37-52 N.m (3.8-5.3 m-kg, 27-38 ft-lb)
Tensioner and Tensioner Spring
1. Install the tensioner and the tensioner spring.
2. Temporarily secure the tensioner with the spring fully ex-
tended.
-’
o5uoBx-229
02-84

ASSEMBLY
13EOB2.03
13EOB2-03.
3 1
03UOB2-111
23UOB2-04: 3
Timing Belt
1. Verify that the timing belt pulley mark is aligned with the tim-
ing mark.
2. Verify that the camshaft pulley marks are aligned with the
seal plate marks.
3. Install the timing belt so that there is no looseness at the
idler side or between the camshaft pulleys.
4. Install the pulley boss and pulley lock bolt.
Caution
l Do not turn the crankshaft counterclockwise.
5. Turn the crankshaft two turns clockwise and face the pin
on the pulley boss upright.
6. Verify that the camshaft pulley marks are aligned with the
seal plate marks.
If not aligned, remove the timing belt and repeat from ten-
sioner installation.
7. Turn the crankshaft 1 and 5/6 turns clockwise, and align
the timing belt pulley mark with the tension set mark for prop-
er timing belt tension adjustment.
8. Loosen the tensioner lock bolt to apply tension to the tim-
ing belt.
9. Tighten the tensioner lock bolt.
Tightening torque:
37-52 N-m (3.8-5.3 m-kg, 27-38 ft-lb)
10. Turn the crankshaft 2 and l/6 turns clockwise and verify
that the timing marks are correctly aligned.
B2-85

I 23UOB2-044
82 ASSEMBLY
DEFLECTION CHECKING POlNT
--; 11. Measure the timing belt deflection by applying moderate
oressure (98 N, 10 kg, 22 lb) midway between the two cam-
shaft pulleys.
If the deflection is not correct, repeat from Step 7 above.
Deflection:
9.0-11.5mm (0.35-0.45 in) at 98 N (10 kg, 22 lb)
Timing Belt Cover
1. Install the lower, middle, and upper covers.
Tightening torque:
7.8-11 N.m (80- ,110 cm-kg, 69-95 in-lb)
I 13EOB2-037
82-86
Pulley lock bolt
1. Hold the flywheel (MIX) or drive plate (ATX) with the SST
and tighten the pulley lock bolt.
Tlghtening torque:
157-167 N.m (16-17 m-kg, 116-123 ft-lb)
Cankshaft pully
1. Install the crankshaft pulley.
2. Install the plate.
3. Tighten the pulley bolts.
Tightening torque:
12-17 N-m (1.25-l -75 m-kg, 9-13 ft-lb)
Water Pump Pulley
1. Install the water pump pulley.
Tightening torque:
7.8-11 N*m (80-110 cm-kg, 69-95 in-lb)

WATER PUMP WATER PUMP
E
REMOVAL / INSTALLATION
Caution
l Do not disassemble the water pump. If a problem is found, replace the pump as a Unit.
1. Disconnect the negative battery cable.
2. Drain the engine coolant.
3. Remove in the order shown in the figure, referring to
Removal Note.
4. Install in the reverse order of removal.
B6 SOHC AND BP SOHC
83, t B6, BP SOHC
I
I
L-----------------_-- ------- -1
/ \/
19-26 (1.9-2.6, 14-19) LVVVLI. YY,
1. Timing belt 4. Water pump assembly
Service ., . . .., ,, ., . . . . . ,. ,.,. ., ,., . . ,,.... . . . . , Section Bl Inspect for cracks, damaged mounting
2. Water inlet pipe
and gasket surface, bearing condition, and leakage
3. Water bypass pipe and O-ring 5. Water pump gasket
E-l 1

BP DOHC
L 7.8-11 N-m (60-110 cm-kg, 69-95 in-lb)
E WATER PUMP
157-167
I
(W-17, 116-123) I
I
/
I
I
I
---N-w------
---------------
----_---_
-I
N.m (m-kg, ft-lb) 1
^^, *--., ^^^
1. Timing belt
Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Section 5. Water pump assembly
B2
2. Water inlet pipe and gasket Inspect for cracks, damaged mounting
3. Water bypass pipe and O-ring surface, bearing condition, and leakage
4. Oil dip stick pipe bracket 6. Water pump gasket
Steps After Installation
1. Fill the radiator with the specified amount and type of engine coolant. (Refer to page E-6.)
2. Connect the negative battery cable,
3. Start the engine and check for leaks.
03UOEX-018
E-12

ENGINE TUNE-UP F
03UOFX.051
03UOFX-051
- w4TEN I
Air Cleaner Element
Inspection
1. Check the air cleaner element for excessive dirt, damage,
or oil.
Caution
l Do not use compression air to clean the element.
2. Replace the element if necessary.
ADJUSTMENT
Preparation
1. Warm up the engine to normal operating temperature.
2. Turn all electric loads OFF.
3. Connect the
SST to the diagnosis connector.
4. Connect a timing light.
5. Connect a tachometer to the diagnosis connector
IG- ter-
minal as shown.
6. Set switch @to position 1.
7. Set TEST SW to SELF-TEST.
Note
l If the SST is not used, jump across the TEN termi-
nal and the GND terminal of the diagnosis con-
nector.
Ignition Timing
1. Perform “Preparation”. (Refer to above.)
2. Check if the timing mark (yellow) on the crankshaft pulley
and the mark on the timing belt cover are aligned.
Specification:
Engine
Ignition Timing BTDC B6 BP SOHC BP DOHC
6O-8* 4O--6O go-110
SOHC DOHC
I 03UOFX-054
3. If the marks are not aligned, loosen the distributor lock bolts,
and turn the distributor to make the adjustment.
4. Tighten the distributor lock bolts to the specified torque.
Tightening torque:
19-25 N#m (1.9-2.6 m-kg, 14-19 ft-lb)
5. Disconnect the SST.
F-79

G
ENGINE ELECTRICAL SYSTEM
INDEX ......................................................
OUTLINE ..................................................
SPECIFICATIONS .................................... G- 3
TROUBLESHOOTING
GUIDE.. .................... G-
4
DIAGNOSTIC INDEX ................................
SYMPTOM TROUBLESHOOTING..
............. :- t
-
CHARGING SYSTEM ................................. G- 6
PREPARATION .......................................
CIRCUIT DIAGRAM ................................. :I ;
TROUBLESHOOTING .............................. G- 7
BATTERY ............................................... G- 6
ALTERNATOR ........................................ G-10
DRIVE BELT ........................................... G-14
IGNITION SYSTEM .................................... G-15
PREPARATION ....................................... G-15
CIRCUIT DIAGRAM ................................. G-15
TROUBLESHOOTING .............................. G-16
IGNITION TIMING ................................... G-17
HIGH-TENSION LEAD .............................. G-17
SPARK PLUGS ....................................... G-16
IGNITION COIL ....................................... G-19
DISTRIBUTOR ........................................ G-20
IGNITER ................................................ G-23
STARTING SYSTEM .................................. G-24
PREPARATION ....................................... G-24
CIRCUIT DIAGRAM ................................. G-24
STARTER ...............................................
G-25
STARTER INTERLOCK SWITCH (MTX)
........ G-31
03UOGX-001

OUTLINE G
OUTLINE
SPECIFICATIONS
Item EnginelTransaxle
‘-2, B6 SOHC BP SOHC BP DOHC
MTX 1 ATX MTX ( ATX
Voltage v 1 12
I
3attery
Dark current*’ Type and capacity
(20-hour rate)
mA 55D23L (60AH) 55D23L (60AH)
Max. 20.0
L\lternator
Starter
Type AC
output V-A 12-65
Regulator type Transistorized (built-in IC regulator)
Regulated voltage V 14.1-14.7
Brush length Standard 21.5 (0.846)
mm (in) Minimum 8.0 (0.315)
Drive belt deflection
New
98 N (10 kg, 22 lb)
mm (in) Used 8-Q (0.31-0.35)
Q-10 (0.35-0.39)
Type
I Direct Direct
I Coaxial
Direct Coaxial
reduction reduction I
output V-kW 12-0.95 12-0.95 12-1.4
12-0.95 12-1.4
Brush length Standard 17 (0.67) 17 (0.67) 17.5 (0.69) 17 (0.67)
17.5 (0.69)
mm (in) Minimum 11.5 (0.453) 11.5 (0.453) 10.0 (0.39) 11.5 (0.453) 10.0 (0.39)
Distributor
Ignition timing BTDC
(TEN terminal of diagnosis connector grounded) Electronic spark advance (photo diode)
6O--8O 4O-6O Q”-1 1 o
Ignition coil
Spark plug Resistance
(at 20% [68OF]) Primary
coil winding 0.81-O.QQg
Secondary
coil winding IO-16 kg
BKR5E-11 BKR5Ell BKR5Ell
NGK
BKR6E-11 BKRGEl 1 BKRGEli
BKR7Ell
Type NIPPON-
DENSON Kl GPR-Ul l
K20PRU 11 KIGPR-Ull
K20PR-Ul l KIGPR-Ull
K20PRUll
K22PR-Ul l
I Plua aao mm (in) I 1.0-l .l (0.039-0.043)
Firing order
’ Dark current is the constant flow of current while the ignition switch is OFF.
(i.e. engine control unit, audio, etc.) l-3-4-2
23lJOGX-00
G-3

TD TECHNICAL DATA
MEASUREMENTS
I ._.____2_ nem
Overall length
Overall width
Overall height
Wheel base
Front tread
Rear tread Body ) mm (in)
mm (in)
mm (in)
mm (in)
mm (in)
mm (in) PRfWFr.f! . . ..s .-VW Hatchback 4,355 (171.5) 4,155 (163.6)
1,675 (65.9) 1,670 (65.7)
1,375 (54.1) 1,380 (54.3)
2,500 (98.4) 2,450 (96.5)
1,430 (56.3)
1,435 (56.5)
Bl. ENGINE (B6 AND BP SOHC)
1 Type
1 Cylinder arrangement and number Engine
86 SOHC BP SOHC
^ . . _
,?
I
uasollne, 4-cyw
. . *. 4
in-line 4-cyrinaer
Pentroof
1
I Combustion chamber I Multispherical
J Valve system OHC, belt-driven OHC, belt-driven 16 valves
. , I (3.07 x 3.29) 83.0 x 85.0 (3.27 x 3.35)
Total piston displacement cc (cu in) 1,597 (97.4) 1,839 (112.2)
Compression ratio 9.3 8.9
) Standard 1,236 (12.6, 179)-300 1,197 (12.2, 173)300
I
863 (8.8, 125)-300 834 (8.5, 121)300 1 Bore x Stroke
mm (in) I 78.0 x 83.6
Compression pressure
kPa (kg/cm’, psi)-rpm
E cvlinders 1 Maximum difference
196 (2.0, 28)
I
, ------- ---- -J - IN Open BTDC 14O 2O
Close ABDC 50°
Valve timing
Open BBDC 52O 55O
EX
Close ATDC 12O 8O
IN 0 Maintenance-free I \/AIo &-in --
Valve clearance EX 0 Maintenance-free
(Warm engine) mm (in) / ,,syi: 1
IN 0 Maintenance-free
I , EX 0 Maintenance-free
I Cylinder head
Height
Distortion
Grinding Valve and T _
Valve head diameter
Valve head margin thickness
Valve face angle IN mm (in) EX
IN
mm b-4 Fx mm (in) 107.4-107.6 (4.228-4.236)
mm (in) 0.15 (0.006) max. 0.10 (0.004) max.
mm (in) 0.20 (0.008) max. 0.10 (0.004) max.
37.9-38.1 (1.492-l ,500) 29.9-30.1 (1.177-1.185)
31 .Q-32.1 (1.256-l ,264) 24.85-25.15 (0.978-0.990)
0.8 (0.031) 0.9 (0.035)
1.1 10.043) 1 .o (0.039)
-, ,
\- I
IN 45O
EX 45O
I I Standard
IN
Minimum
Valve length mm (in)
EX Standard
Minimum I”L. I, \*.“cL
Valve stem diameter IN
mm On) EX 6.970-6.985 (0.2744-
6.965-6.980 (0.2742-
Guide inner diameter
I Valve stem-to-guide clearance mm (in) lTj7---- ,
Maximum 103.77 (4,085) 101.77 (4.007)
103.27 (4.066) 101.27 (3.987)
102.67 (4.042) 102.97 (4.054)
,n+ 47 IA noo
1 102.47 (4.034)
-0.2750) 5.970-5.985 (0.2350-0.2356)
-0.2748) 5.965-5.980 (0.2348-0.2354)
3.2760-0.2768) 6.01-6.03 (0.2366-0.2374)
0.025-0.060 (0.001 O-0.0024)
0.030-0.065 (0.001 l-0.0026)
-.
I
mm (in) 1 7.01-7.03 (r ‘
1 IN
Guide projection (Height “A”) IN
mm (in) Ex 13.2-l 3.8 (0.520-
13.2-13.8 (0.520-
TD-2