torque MITSUBISHI 3000GT 1991 Manual Online

31-2WHEEL AND TIRE - Specifications
SPECIFICATIONS
GENERAL SPECIFICATIONS
MOICA- -
‘\
Items
Wheel
Tire size
Wheel type
Wheel size
Amount of wheel offsetmm (in.)
Tire inflation pressure
kPa (psi)
Front
Rear
DOHC-N/A
225l55R 16 93U
Aluminum type
16X8J ’
46 (1.8)
220 (32)
200 (29)DOHC-T/C
245145ZR 17
Aluminum type
17 x
8.5J
46 (1.8)
220 (32)
200 (29)
Spare wheel
Tire size
T125190D16T135/90D16
Wheel size
l6x4Tl6x4T
Amount of wheel offsetmm (in.)46 (1.8)46 (1.8)
Tire inflation pressurekPa (psi)
420 (60)420 (60)
SERVICE SPECIFICATIONSM31CB. -
Items
Specifications
Limit
Wheel
runout
Radialmm (in.)2.0 (.08)
Lateralmm (in.)2.0 t.08)
Tread depth of tiremm (in.)1.6 (.06)
TORQUE SPECIFICATIONSMBlCC- -
ItemsNm
Hub nuts120- 140
ft.lbs.
87-iO1TSB Revision

33A-2FRONT SUSPENSION - Specifications
SPECIFICATIONSM33CA-A
GENERAL SPECIFICATIONS
Items
Coil spring identification colorM/T: Orange x 1
ATT: Orange x 2
Shock absorber
Type
Maximum length
Compressed length
Damping force
[at 0.3 m/set. (0.984 ft./set.)]
Hydraulic, cylindricaldouble acting type
485 + 3 (19.09
f .12)335
I 3 (13.19 + .12)Hydraulic, cylindrical double acting type
485
k 3 (19.09 + .12)335 2 3 (13.19 +
.12)
150 (5.91)
NOTE*: OptionHard
: 2,650 + 360 (584 + 79)
Medium : 1,650 t 230 (363 ?I 51)
Soft : 650 f 100 (143 + 22)
Hard
: 1,200 + 170 (265 * 37)
Medium : 1 ,I 50 k 170 (253 +37)Soft :1,000 z!z 150 (220 + 33
SERVICE SPECIFICATIONSM33CB-A
Camber
Caster
Toe-inmm (in.)
Lower arm ball joint starting torque
Nm (in.lbs.)IO-22 (86-191)
Stabilizer link ball joint starting torqueNm (in.lbs.)1.7 - 3.2 (15 - 28)
Steering angle
Inner wheelTSB Revision

33A-4FRONT SUSPENSION - Service Adjustment Procedures
Strut lowermounting bolt(upper)
\/
0 camber@ camber12FOO31
SERVICE ADJUSTMENT PROCEDURES
M33FBAT
FRONT WHEEL ALIGNMENT‘d
TOE-INStandard value: 0 2 3 mm (0 +
.12 in.)
1. Adjust the toe-in by undoing the clips and turning the left
and right tie rod turnbuckles by the same amount (in
opposite directions).
2.After making the adjustments, use a turning radius gauge to
confirm that the steering wheel turning angle is within thestandard value range. (Refer to GROUP 37A
- Service
Adjustment Procedures.)Standard value:
Inner wheel
33”45’Outer wheel
28”21’
CAMBER AND CASTERStandard value:
Camber0” IL 30’
Caster3”55’ IL 30’
Install the special tool by tightening it to the same torque as
that applied to the drive shaft nut.
a
To adjust camber, turn the strut lower mounting bolt (upper).
One graduation is equivalent to about 20’ in camber. Caster hasbeen factory-adjusted to the standard value and requires no
adjustment.
Caution
1.One camber graduation changes toe by about 0.5 mm
(.02 in.). Be sure to adjust toe after camber has been
adjusted.
2.The difference in camber between right and left shouldbe within
O”30’.
WHEEL BEARING ADJUSTMENTM33FCAA
Bearing preload is pre-set to the specified value by design andtherefore can not be adjusted.
TSB Revision
1

FRONT SUSPENSION - Strut Assembly33A-7
INSPECTIONM33LGAFl Check the strut insulator bearing- for wear or rust.
l Check the rubber parts for damage or deterioration.
lCheck the spring for deformation, deterioration or damage.l Check the shock absorber for deformation,
Strutmsulatkx bearing
12FOO80
SERVICE POINTS OF REASSEMBLYM33UlAM
4. INSTALLATION OF SPRING UPPER SEAT ASSEMBLY
(1) Assemble the spring upper seat to the piston rod, fitting
the notch in the rod to the shaped hole in spring seat.(2) Line up the holes in the strut assembly spring lower
seat with the hole in the spring upper seat.
NOTEThe job is easily accomplished with a pipe
[$I 8 mm x
300 mm
(4 .3 in. x 11.8 in.)].
2. INSTALLATION OF SELF-LOCKING NUT
(1) With the coil spring held compressed by the special
tools (MB991 237 and MB991 238). provisionally .tightenthe self-locking nut.
(2) Correctly align both ends of the coil spring with the
grooves in the spring seat, and then loosen the special
tools (MB991 237 and MB991 238).
(3) Using the special tool, tighten the strut insulator at the
specified torque.12FOO20
iTSB Revision

33A-8FRONT SUSPENSION - Lower Arm
LOWER ARMMOJNA- _
REMOVAL AND INSTALLATION
100 Nm-Ts. *....
2’ /40 Nm
29 ft.lbs.Removal steps
1. Stabilizer link mounting nut (stabilizer barside)
l *
2. Stabilizer link mounting nut (lower arm side)
3. Stabilizer link
4.
Self-lockrng nut connecting lower arm ball
joint to knuckle
5. Lower arm mounting nut
6. Lower arm mounting bolt
7. Clamp mounting self-locking nut
8. Clamp mounting bolt (small)
9. Clamp mounting bolt (large)
** 10. Lower arm clamp mounting self-locking nut11. Lower arm mounting clamp
12. Lower arm
.- -NOTE
shteld
1210487
13. Stopper
14. Dust shieldFor tlghtenrng points marked with *, ftrst temporarily trghten
15. Rod bushing
them, then ground the vehicle and torque to specificationwhere the vehrcle is empty.TSR Revision

FRONT SUSPENSION - Lower Arm33A-9
MB991 113-0112R0258
12UOO18
LIPS
Dust
shield
12R0487
MB990799-01
Dust shield
Snap ring12L0295
SERVICE POINT OF REMOVALM33NBAO4. REMOVAL OF LOWER ARM BALL JOINT
Using the special tool, disconnect the knuckle from the
lower arm ball joint.
NOTE
(1) Do not remove the nut from the ball joint, but just
loosen it.
(2) Suspend the special tool with a rope to prevent it from
dropping.
INSPECTIONM33NCAFl Check the bushing for wear and deterioration.
l Check the lower arm for bend
,or breakage.
l Check the clamp for deterioration or damage.
l Check the ball joint dust shield for cracks.
l Check all bolts for condition and straightness.
CHECKING BALL JOINT FOR STARTING TORQUEMount two nuts on the ball joint, and then measure the ball
joint starting torque.
Standard value: 10
- 22 Nm (86 - 191 in.lbs.1
BALL JOINT DUST SHIELD REPLACEMENTMJBNEAH(1) Remove the dust shield.
(2) Apply multipurpose grease to the lip and inside of the dust
shield.(3)
C$Fedn the dust shield with special tool until it is fully
TSB Revision
SERVICE POINT OF INSTALLATIONM33NFAP
10. INSTALLATION OF LOWER ARM CLAMP MOUNTING
SELF-LOCKING NUT
Place the lower arm bushing bracket so that its mountingsurface tilts 6”
? 1” with respect to the bottom surface of
the lower arm; then, mount the self-locking nut.

FRONT SUSPENSION - Stabilizer Bar33A-11CHECKING STABILIZER LINK BALL JOINT STARTING
TORQUE
12LO24412LO217
Tapeeke
12PO156
Clip ring ends
(Could be on 180”
opposite side)1280252
Align end of bushinwith marking outerMount two nuts on the ball joint, and then measure the ball
joint starting torque.
Standard value: 1.7
- 3.2 Nm (15 - 28 in.lbs.)
BALL JOINT DUST SHIELD REPLACEMENTM33TEAF(1) Remove the clip ring and the dust shield.
(2) Apply multipurpose grease to the lip and inside of the dust
shield.
(3) Use vinyl tape to tape the stabilizer link where shown in the
illustration, and then install the dust shield to the stabilizer
link.(4) Secure the dust shield by the clip link.
At this time, make sure that the clip ring ends are located ata point 90”
? 20” with reference to the link axis.
SERVICE POINT OF INSTALLATIONM33TOAO
5. POSITIONING OF STABILIZER BAR BRACKET
(1) Align the bushing (LH) with the stabilizer bar markingend and temporarily tighten the stabilizer bar bracket
U-0.
(2) In this condition, mount the stabilizer bar bracket (RH)and temporarily tighten it.
(3) Temporarily fix the both ends of the stabilizer bar to the
link and tighten the stabilizer bar bracket mounting bolts
to specification:
1 TSB Revision

id
REAR
SUSPE,NSlON
CONTENTSM34AA-.

REAR SUSPENSION ASSEMBLY. . . . . . . . . .._..24
SERVICE ADJUSTMENT PROCEDURES. .
23
Rear Wheel Alignment Inspection. . . . . . . . . .23
SHOCK ABSORBER ASSEMBLY. . . . . . . . . . . . .33
SPECIAL TOOLS .
.._____......_..................._.................20SPECIFICATIONS
.__............................................. 19
General Specifications. . . . . . . . . . . . . . . . . . . .19
/
id
Service Specifications.._............................... 19
STABILIZER BAR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34TRAILING ARM
.._........_._...................................... 30
TROUBLESHOOTING
_....................................... 22
UPPER AND LOWER ARM. . . . . . . . . . . . . . . . . . . ..t..........27
REAR AXLE HUB................................................
17
REAR SUSPENSION ASSEMBLY....................7
SERVICE ADJUSTMENT PROCEDURES........5
Rear Hub Rotary-sliding Resistance
(Torque) Inspection................................................
6
Rear Wheel Alignment Inspection....................
5
Wheel Bearing End Play Inspection....................6
SHOCK ABSORBER ASSEMBLY....................13
SPECIAL TOOLS....................................................
3
SPECIFICATIONS................................................2
,General Specifications....................................2
Service Specifications....................................2
STABILIZER BAR................................................15
TRAILING ARM....................................................11ITROUBLESHOOTING
4........................................UPPER ARM, LOWER ARM AND
ASSIST LINK91........................................................
iI

34-2REAR SUSPENSION - Specifications
SPECIFICATIONS
GENERAL SPECIFICATIONS
Items
Suspension system
Coil spring
Wire dia. x O.D. x free lengthmm (in.)
Coil spring identification color
Spring constantN/mm (Ibs./in.)
Shock absorber
Type
Max. lengthmm (in.)
Min. lengthmm (in.)
Strokemm (in.)
Damping force [at 0.3 m/set. (.9 ftisec.)]
ExpansionN (Ibs.)
ContractionN (Ibs.)aheel
bearing
Type
Vehicles without ECSVehicles with ECS
Multi-link12X95X350
12.2x105x350(47 x 3.74 x 13.78)(.48x4.13x13.78)
Pink x 1
Orange x 1
352 1.8(196? 10.1)35+ 1.8(196+ 10.1)
Hydraulic cylindricaldouble-acting typeHydraulic cylindricaldouble-acting type
515
f 3 (20.2 i .I)515 + 3 (20.2 f .I)
356+3(14.0+.1)356 Ifr 3 (14.0 k .I)
159 (6.3)
159 (6.3)
1,000 + 150 (220 + 33)Hard: 1,800 ? 250 (397 f 55)
Medium: 1,200
rt 170 (265 + 37
Soft: 550
* 90 (121 f 20)
550_+80(121 + 18)Hard: 950 + 140 (209 k 31)
Medium: 850
* 130 (187 f 29)
Soft: 650
t- 100 (143 i 22)
Unit bail bearing
SERVICE SPECIFICATIONSM34CB.A
Items
Specifications
Standard value
Toe-in (Left-right difference)
mm (in.)
Camber
Stabilizer link ball joint starting torque
Nm (in.lbs.)
Ball joint rotation starting torque
Nm (inlbs.)
Stabilizer link protrusion
mm (in.)
Crossmember bushing projection,mm (in.)
I0.5 + 2.5
(.Ol + .09)
0” 2 30’
1.7-3.2(15-28)
2-9(17-78)
5-7(.197-,276)
8.5 - 9.5 (33 - .37)
Limit
Wheel bearing end playmm (in.)
Rear hub rotary-sliding resistance
N (Ibs.)
Rear hub rotary-sliding torqueNm (ftlbs.)0.05
(002) or less
31 (7) or less
1.8 (I .30) or lessTSB Revision

34-6REAR SUSPENSION - Service Adiustment Procedures12NOOOl
WHEEL BEARING END PLAY INSPECTIONM34FBAG
1.Inspect the play of the bearings while the vehicle is jackedup and resting on floor jack.
2. Remove the hub cap and then release the parking brake.
s&i3. Remove the caliper assembly and the brake disc.
4. Check the bearing’s end play.
Place a dial gauge against the hub surface; then move the
hub in the axial direction and check whether or not there is
end play.Limit: 0.05 mm
(.002 in.) or less
NOTEIf the limit value is exceeded, the lock nut should be
tightened to the specified torque and check the end play
again.5. Replace the rear hub bearing unit if an adjustment cannot
be made to within the limit.
REAR HUB ROTARY-SLIDING RESISTANCE (TOR-
QUE) INSPECTION
M34FCAC
1.Inspect the play of the bearings while the vehicle is jackedup and resting on floor jack.
2. Release the parking brake.
3. Remove the caliper assembly and the brake disc.
..J
4.After turning the hub a few times to seat the bearing, attach
a spring balance to the hub bolt, and, pulling at a 90” anglefrom the hub bolt, measure to determine whether or not
the rotary-sliding resistance of the rear hub (the
rotary-sliding torque of the rear hub) is the standard value.
Limit:
Rear hub rotary-sliding resistance
31 N (7 Ibs.) or lessRear hub rotary-sliding torque
1.8 Nm (1.30 ftlbs.) or less
NOTEIf the limit value is exceeded, the lock nut should be
tightened to the specified torque and check the end play
again.5. Replace the rear hub unit bearing if an adjustment cannot
be made to within the limit.
TSB Revision